Summary of the content on the page No. 1
For all customer enquiries or for replacement parts, contact:-
☎ ☎ 01325 300303
www.flymo.com
eop.customer.services@electrolux.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
Summary of the content on the page No. 2
Safety Please Note:- This manual covers various products. Please read the user instructions care- fully to fully identify, assemble and use the features that apply to your product. If not used properly this lawnmower can be dangerous! This lawnmower can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure rea- sonable safety and efficiency in using this lawnmower. The operator is responsible for following the warning and safety instr
Summary of the content on the page No. 3
16. Remove the plug from the mains : Maintenance and storage - before leaving the mower unattended for any period; 1. Keep all nuts, bolts and screws tight to be sure the - before clearing a blockage; lawnmower is in safe working condition. - before checking, cleaning or working on the appli- 2. Check the grassbox frequently for wear or deterioration. ance; 3. Replace worn or damaged parts for safety. - if you hit an object. Do not use your lawnmower 4. Only use the replacement blade, blade bo
Summary of the content on the page No. 4
Upper Handle Assembly Fitting Upper Handles to Lower Handles (D & E) D E 1. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost 2. Ensure the upper handle and the lower handle are aligned correctly. 1 3. Insert the nut into the handle knob. (if applicable) (D1) 4. Fit the bolts, washers and handle knobs. 5. Fit the cable to the handles with the clips provided. Make sure the cable is not trapped between the han- dles. Venturer 370 RE420/420c Grassbox A
Summary of the content on the page No. 5
Cutting Height Adjustment Wheel removal Wheel removal L1 L2 Cutting Height with removal of wheels (L1, L2, L3) If your lawnmower has wheel hubs as illustrated in Fig L1, the height of cut is adjusted by following steps L1 - L3. Wheel removal Levers fitted L3 M1 1. Remove the wheel by turning the wheel hub in an 3 anticlockwise direction (L1) and relocate in new hole (L2) turning the wheel hub in a clockwise direction to tighten (L3). Repeat for other wheels adjusting to 2 the same position. 1
Summary of the content on the page No. 6
How to Mow 1. Start mowing the edge of the lawn nearest to the T power point so that the cable is laid out on the lawn you have already cut (T). 2. Mow twice a week in the growing season, your lawn will suffer if more that one third of its length is cut at one time and this may also result in poor collection. • Please Note Do not overload your Lawnmower When mowing in long thick grass a first cut with the cutting height adjusted to its highest setting, (see Cutting Height Adjustment), will help
Summary of the content on the page No. 7
Fault Finding Hints Fails to Operate 5. If poor collection persists. Immediately disconnect from the mains electric- 1. Is the correct Starting procedure being followed? See ‘To Start your Lawnmower’. ity supply and consult your local approved 2. Is the Power Turned On? Electrolux Outdoor Products Service Centre. 3. Check the fuse in the plug, if blown replace. Excessive Vibration 4. Fuse continues to blow? 1. Disconnect from the mains electricity supply. Immediately disconnect from the mains el
Summary of the content on the page No. 8
Service Recommendations 1. We strongly recommend that your product is serv- 6. Should it be necessary for work to be carried iced at least every twelve months, more often in a out by your Service Centre, it is important to professional application. take your complete machine including cable and 2. Always use genuine Flymo Spare Parts. any extension cables used. 3. Prepacked spares are available from most A network of specialist dealers can be found in your local Electrolux Outdoor Products stock
