Summary of the content on the page No. 1
VENTURER 32 (VTR32)
®
VISIMO (VM032)
ROLLERMO (RM032)
EASIMO (EM032)
Original Instructions
ROLLERMO
VENTURER 32
EASIMO
VISIMO
IMPORTANT INFORMATION
Read before use
& retain for future reference
Summary of the content on the page No. 2
Carton Contents switchbox start/stop lever lock off cable clip x 2 button grassbox washer x 4 handle upper handle bolt x 2 wingknob x 4 grassbox upper grassbox lower Easimo only grassbox tongue electric cable with moulded safety flap on plug lower handle x 2 motor cover instruction deck manual IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. The Loose Parts Pack is packaged underneath the deck of the product. IF ANY PARTS ARE MISSING CON
Summary of the content on the page No. 3
2. Never allow children or people unfamiliar with the instruc- signs of wear or damage and repair as necessary. tions to use the machine. 4. Replace worn or damaged blades together with their 3. Stop using the machine while people, especially children, fixings in sets to preserve balance. Use or pets are nearby. 4. Only use the product in the manner and for the func- 1. Use the product only in daylight or good artificial light. tions described in these instructions. 2. Avoid operating your produ
Summary of the content on the page No. 4
Assembly Instructions The Loose Parts Pack is packaged underneath the deck. A Assembly of Lower Handles to Deck 2 3 1. Place the bolt (A2) through the hole in the lower handle (A1) until the lower handle fits into the recess (A3) 2. Place the washer (B1) and the wing knob (B2) on to 1 the bolt and tighten the wing knob. 3. Repeat on the other side. Assembly of Upper Handles to Lower Handles. 1. Ensure the upper handle is located correctly with the B lock-off button on the switchbox uppermost
Summary of the content on the page No. 5
Grassbox G 1 Fitting Fully Assembled Grassbox to Lawnmower. 1. Lift safety flap (G1) 3 2. Make sure the discharge chute is clean and free from debris (G2) 3. Locate fully assembled grassbox onto 2 location points (G3) at the rear of the deck as illustrated in pic. H 2 4. Locate safety flap onto the top of the grassbox. En- sure the grassbox is securely located. H IMPORTANT ! AFTER FITTING ENSURE NO GAP REMAINS BE- TWEEN THE SAFETY FLAP AND THE GRASS- BOX. • Removal is the reverse procedure.
Summary of the content on the page No. 6
Starting and Stopping To Start your Lawnmower M N 1. Form loop in mains cable and push the loop through the slot. (M) 2. To secure, position loop over the hook and pull the cable back through the slot (N). 3. Connect plug to mains and switch on. 4. Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn damage whilst starting. P Q The switchbox is provided with a lock-off button (P1) to prevent accidental starting. 5. Press and hold the lock-off butt
Summary of the content on the page No. 7
Removing and Fitting the Blade Switch off, wait until the blade has stopped rotating S and disconnect from the mains electricity supply BE- blade bolt FORE attempting to remove or refit the blade. Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Removing the Blade washer 1. To remove the blade bolt, hold the blade firmly with a gloved hand and with a spanner, loosen the blade bolt by turning it anti-clockwise (S). blade 2. Remove the blade bolt, washer and blade.(
Summary of the content on the page No. 8
Caring for your Lawnmower Cleaning V1 V2 USE GLOVES IMPORTANT:- It is very important that you keep your lawn- mower clean. Grass clippings left in any of the air intakes or under the deck could become a potential fire hazard. 1. Remove grass from under the deck with brush. (V1) 2. Using a soft brush - remove grass clippings from all air intakes (V2), the discharge chute (V3) and the grass box (V4). 3. Visimo Only - Using a soft brush, remove grass clip- pings from the vision window (V5). V3
Summary of the content on the page No. 9
Service Recommendations 1. We strongly recommend that your product is serviced at 6. Should it be necessary for work to be carried out by your Service Centre, it is important to take your complete ma- least every twelve months, more often in a professional application. chine including cable and any extension cables used. 2. Always use genuine Spare Parts. A network of specialist dealers can be found in your local 3. Prepacked spares are available from most Husqvarna UK Yellow Pages. Ltd. stockis
Summary of the content on the page No. 10
EC Declaration of Conformity Husqvarna UK Ltd., Aycliffe Industrial Park Newton Aycliffe, Co. Durham, DL5 6UP, England Declare under our sole responsibility that the product(s); Category........................................ Electric Rotary Lawnmower Model(s)......................................... VTR32, VM032, RM032, EM032 Identification of Series................... See Product Rating Label Year of Construction...................... See Product Rating Label Complies with the essential requ
