Summary of the content on the page No. 1
Summary of the content on the page No. 2
READ CAREFULLY IMPORTANT The Dixon ZTR mower is both easy and fun to You have purchased a top quality lawn mower that has been carefully inspected and adjusted at the operate. However, any power mower must be factory. This lawn mower is warranted for 1 year from operated properly to be safe. It is not a toy or a date of delivery against all defects in materials and recreational vehicle. Before you start to use the workmanship. Lawn mowers used for commercial mower, read the operator's
Summary of the content on the page No. 3
SERIAL NUMBERS The lawn mower has three serial numbers: Mower Number — Located on frame at right rear transaxle mount. Transaxle Number — Located on transaxle. Engine Number — Located on engine. When referring to serial number on Warranty Registration, etc., use Mower Serial Number located on frame. deflector which directs downwards all blade - SAFETY INSTRUCTIONS propelled objects, keep persons clear of the BEFORE MOWING discharge chute. Do not operate mower unless 1. Read these safety
Summary of the content on the page No. 4
TO GO BACKWARD IMPORTANT OPERATING From neutral position gently pull both drive INSTRUCTIONS levers rearward. Dixon ZTR mowers offer a new concept in mowing, TURNING providing unique maneuverability and ease. The Turning is controlled by moving one drive lever following procedures will allow one to become slightly forward or rearward of the other. To turn familiar with the unique method of control very left, move left lever rearward of right lever. To easily. turn "square corners"
Summary of the content on the page No. 5
ALWAYS DISENGAGE BLADE OPERATION terminal. (See also wiring diagram shown on BEFORE DISMOUNTING. Body Assembly illustration.) 3. Clean top of battery and terminals. 9. Parking Brake: 4. Do not remove battery from mower. Parking brake is on right hand side of floor area and is 5. To reactivate, reconnect cables to correct engaged by pushing full forward with foot. To terminals and charge battery if needed. disengage, pull lever back toward operator by hand. In emergency situations, brak
Summary of the content on the page No. 6
BODY REMOVAL CHAIN DRIVES ADJUSTMENT A. ZTR-424 Body Removal To adjust the drive chains, the body must be 1. Disconnect throttle cable from engine. removed and shims added behind the transaxle. 2. Disconnect key switch wire loom from frame Loosen 4 bolts which hold the transaxle to the wire loom at front of body. frame. Insert shims as needed for adjustment 3. Disconnect seat switch wire loom from frame between transaxle and mount plates. When properly wire loom. This connection is
Summary of the content on the page No. 7
ELECTRICAL SYSTEMS TRANSAXLE Keep all connections clean and tight. Maintain the fluid For adjustment or repair confer with authorized Dixon dealer service department. Adjustment or in the battery at correct level. repair by other than authorized dealer voids BODY warranty. The body may be washed with a mild detergent and waxed with any automotive type wax. SPARE PARTS See your dealer for ordering spare parts or warranty service. INSTALLING AND REMOVING MOWER DECK FROM FRAME 1. Attac
Summary of the content on the page No. 8
Summary of the content on the page No. 9
Summary of the content on the page No. 10
TRANSAXLE ASSEMBLY 5000-102
Summary of the content on the page No. 11
TRANSAXLE ASSEMBLY 5000
Summary of the content on the page No. 12
Summary of the content on the page No. 13
PARTS LIST FOR 42" Part No. Name Part No. Name 1 1 MODELS 1629 Bumper Weldment 3105 HD / ' x 1 / " Spirol Pin (not shown) 4 4 1 Part No. Name 1635 Double Engine Pulley 3106 HD / 'x 1" Spirol Pin (not shown) 4 1 1 1000C Frame Weldment 1636 Bellcrank Kit 3107 HD / " x 1 / " Spirol Pin (not shown) 4 2 1015 Caster Weldment 1638 Lower Control Lever Assembly 3118 Disc Spring 1020 Caster Axle 1640 Tension Plate 11 h.p. 3502 Hand Grip 1022 Caster Wheel & T
Summary of the content on the page No. 14
Part No. Name Part No. Name 4051 Body, ZTR-422 Part No. Name 5014 Torque Rod 6058 V-Pulley 4054 Seat Switch Assembly, ZTR-422 5015 24 T Sprocket 4058 Arm Rest Bracket R, ZTR-424 6059 Flat Idler Pulley 5016 Moulded Cone (each) 4059 Arm Rest Bracket L, ZTR-424 6060 Serpentine Idler Weldment 5018 9 T Sprocket - Narrow 5 3 4060 Arm Rest 6063 / " OD x / " ID Bronze Bushing 8 8 5019 Transaxle Chain 4061 Pan Swi
Summary of the content on the page No. 15
OWNER INFORMATION Date Mower Purchased___________________Mower Model Number ___________________ Mower Purchased from ________________________________________________________ dealer name & address Mower Serial Number_____________________Transaxle Serial Number _________________ Oil changed this date: 1. ____________________________ 4. ____________________________ 2. ______________________________ 5. ______________________________ 3. ______________________________ 6. _________________
Summary of the content on the page No. 16
Form No. 4089-1279 Litho in U.S.A. ® DIXON and ZTR are registered trademarks of Dixon Industries, Inc.
