Summary of the content on the page No. 1
CP180 / CP180i
GPS Chart Plotters
Owner's Manual
CP180
CP180i
Summary of the content on the page No. 2
WARNING!!! Electronic charts displayed by the GPS chart plotter are believed to be accurate and reliable, but are not intended to be a substitute for the official charts, which should remain your main reference for all matters related to the execution of safe navigation. For this reason we would like to remind you that you should carry on board and use the official published and approved nautical charts. FCC Compliance Statement This device complies with Part 15 of the FCC limits for Class
Summary of the content on the page No. 3
CAUTION - The GPS chart plotter is designed for maritime use. Please give attention to avoid + water intrusion into the C-MAP NT /MAX C-CARD cartridge holder. - Extensive exposure to heat may result in damage to the GPS chart plotter. - The GPS chart plotter contains dangerous high voltage circuits which only experienced technicians can handle. - STANDARD HORIZON will not be liable for errors contained herein, or for incidental or consequential damages in connection with the performance or use o
Summary of the content on the page No. 4
Page 6 CP180 / CP180i
Summary of the content on the page No. 5
TABLE OF CONTENTS 1. INTRODUCTION ...................................................................................................... 11 1.0 GENERAL INFORMATION .................................................................................... 11 1.1 PACKING LIST ...................................................................................................... 11 1.1.0 CP180C/180i Packing List ......................................................................... 11 2. GETTING STARTE
Summary of the content on the page No. 6
6. MAP FUNCTIONS ...................................................................................................... 37 6.0 MAX FUNCTIONS MENU ...................................................................................... 37 6.0.0 Zoom Type ................................................................................................. 37 6.0.1 Perspective View ....................................................................................... 37 6.0.2 Dynamic Nav-Aids ..........
Summary of the content on the page No. 7
12.0.3 Display Mode ............................................................................................. 63 12.0.4 Marine Settings .......................................................................................... 64 12.0.5 Depth Settings ........................................................................................... 64 12.0.6 Land Settings ............................................................................................. 64 12.0.7 Chart Settings .........
Summary of the content on the page No. 8
19. APPENDIX: TERMS ...................................................................................................... 89 INDEX ...................................................................................................... 91 Page 10 CP180 / CP180i
Summary of the content on the page No. 9
1. INTRODUCTION Congratulations on your purchase of the Standard Horizon GPS chart plotter. Whether this is your first GPS chart plotter, or if you have other STANDARD HORIZON equipment, the STANDARD HORIZON organization is committed to ensuring your enjoyment of this GPS chart plotter. STANDARD HORIZON technical support personnel stand behind every product we sell, and our Product Support team invites you to contact us should you require technical advice or assistance, at 800/767-2450, or marin
Summary of the content on the page No. 10
S8101690 Power data cable S8002223 Flush mounting screws (CP180 ONLY) EMO16N550 Flush mount template (CP180 ONLY) Q7000559 GPS WAAS Smart antenna EM023U100 Owner’s Manual EM023U500 Quick Reference Guide Page 12 CP180 / CP180i
Summary of the content on the page No. 11
2. GETTING STARTED 2.0 MOUNTING THE GPS CHART PLOTTER The CP180 is supplied with hardware for bracket or flush mounting, the CP180i is supplied with only with hardware for bracket mounting due to the internal design of the GPS antenna. Below are pictures showing actual examples of the two types of installation. NOTE The CP180i with internal GPS antenna is designed to be bracket mounted only. Do not flush mount or GPS performance possibly will not operate. 2.1 BRACKET MOUNTING The CP180 and CP180
Summary of the content on the page No. 12
2. Drill a hole in one area of the cutout area that will allow the blade of a jig saw to be inserted. Insert and cut out the area on the panel using the jig saw. 3. Next drill the four holes required to insert the GPS chart plotter with the mounting studs. 4. Install the mounting studs on the GPS chart plotter and insert into the mounting hole. 5. Attach the GPS chart plotter to the mounting location by attaching the supplied hardware to the mounting studs. Figure 2.2 - Example of GPS chart p
Summary of the content on the page No. 13
1. Remove the threaded base from the antenna dome. 2. To ease installation a flush mounting template for the antenna has been included. 3. Apply the mounting template sticker to the area that was verified for GPS reception. 4. Then, drill out the 0.63” (16mm) and 0.16” (4mm) holes, and remove the template. 5. Insert the cable into the 0.63” (16mm) hole and route to the GPS chart plotter. 6. Apply a small amount or RTV to the under side of the antenna. 7. Place the antenna and then screw it into
Summary of the content on the page No. 14
6 Gray Port2 Input Connect to Output of NMEA device Default is NMEA0183* 7 White Port2 Output Connect to Input of NMEA device Default is NMEA0183 with GLL, RMB, RMC and XTE sentences 8 Yellow Port3 Output Connect to Output of NMEA device Default is NMEA0183 with APA, APB, XTE, COG and BOD sentences** *NOTE: FF520 FISH FINDER OPTION When a FF520 is connected to the CP180 or CP180i, Port 2 of the NMEA in/out Communi- cation setup menu must be changed to FF520 as shown below for communications. 1.
Summary of the content on the page No. 15
2.5 BATTERY CONNECTIONS 1. The CP180 and CP180i are supplied with a fuse and holder. This fuse should be installed into the Black wire to protect the NMEA Output/Input circuits from becoming damaged. 2. Connect the Red and Black wires from the CP180 or CP180i to a 12VDC source directly as possible. 2.6 NMEA CONNECTIONS The GPS chart plotter can be connected to external devices with NMEA and display information, examples: - DSC VHF Radio - Optional FF520 50/200kHz BLACK BOX FISH FINDER - Depth So
Summary of the content on the page No. 16
Figure 2.8 - FF520 50/200kHz BLACK BOX FISH FINDER 2.9 OUTPUTTING NMEA TO A PERSONAL COMPUTER The GPS chart plotter can be connected to output Marks, Routes and tracks to many PC programs available in the aftermarket. To send or receive User Points the PC Program must be able to receive NMEA WPL and RTE sentences. Pin PC DB9 connection NMEA connection 2 Receive Brown 3 Transmit Blue 5 Signal ground Green 2.10 NMEA DATA PAGE The NMEA Data Page is very useful to see if a External device (example:
Summary of the content on the page No. 17
the following order: Start-up screen, DSC Polling page, GPS Status, Chart/General window, Chart/Compass tape, Chart/Fish, Full page Fish, Navigation page, Highway Page, Celestial page, NMEA Page. NOTE This mode is use by selling dealers to promote the features of the CP180 and CP180i when on a retail shelf. The Demo mode can be selected from the Simulation Menu following the procedure: 1. Press [MENU]. Move the ShuttlePoint knob to highlight SETUP MENU and press [ENT]. 2. Move the ShuttlePoint k
Summary of the content on the page No. 18
Page 20 CP180 / CP180i
Summary of the content on the page No. 19
3. CONTROLS AND INDICATORS NOTE This section defines each control of the GPS chart plotter. For instructions, refer to Getting Started and Advanced Settings sections of this Owner's Manual. 3.0 CONTROLS AND CONNECTIONS The GPS chart plotter is controlled by using the keys located on the front panel. These labeled keys are dedicated to specific functions. As you press a key, a single audio beep confirms the key action; every time a key press is not valid, three rapid beeps sound to indicate that
Summary of the content on the page No. 20
The MARK key Places a Mark under the ships position when in Home Mode (in Cursor Mode under the cursor). The ROUTE key When pressed places a Waypoint. Succeeding presses place more Waypoints to form a Route. The PWR key and Lamp/Contrast Press and hold [PWR] to turn the GPS chart plotter on or off. Once on, press [PWR] to show the Contrast and Lamp popup window. The MOB key When pressed the GPS chart plotter automatically places a Mark on the Chart page and all navigation is towards the position
