Summary of the content on the page No. 1
OWNER'S MANUAL
Read Rules for
Safe Operation
MODEL
and Instructions
Carefully
SE 3612
WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES
GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS
REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR
CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
A GENERAL BATTERY SAFETY
10. Do not use an extension cord unless absolutely necessary.
1. Before you use your battery charger, be sure to read al
Summary of the content on the page No. 2
B. PERSONAL PRECAUTIONS AND SAFETY 1. WARNING: Wear complete eye protection and clothing necklaces, and watches when working with a lead-acid protection, when working with lead-acid batteries. battery. A lead-acid battery can produce a short-circuit 2. Make sure someone is within range of your voice or close current high enough to weld a ring (or the like) to metal, enough to come to your aid when you work with or near a causing a severe burn. 6. Take care not to drop a metal tool or other metal
Summary of the content on the page No. 3
F. OPERATING INSTRUCTIONS: CHARGING BATTERY IN VEHICLE When charging battery in the vehicle, take care to determine the battery type and which post is grounded. To reduce risk of a spark near battery, follow these steps when battery is installed in vehicle. WARNING: A spark near battery may cause battery explosion. WARNING: Do not connect clip to carburetor, fuel lines, or sheet- 1. Position AC power cord and DC charging cords to reduce metal body parts. NOTE: Attach clips to battery post and tw
Summary of the content on the page No. 4
H. OUTPUT SELECTOR CONTROLS Switches Select Switch #1 Furthest left, Use this switch to select the 12volt 200 amp engine start (down) or the 12 volt 40 amp charge (up) 12v 40A 12v 2A up position. The center switch (#2) must be in the (up) position when switch #1 is used. # # # Switch #2 (Center) Use this switch to select use of either switch 1 2 3 #1 or switch #3. Down for switch #3 and up for switch #1. Switch #3 Use this switch to select the 12 volt 2 amp charge (up) or the 6 volt 100 amp engi
Summary of the content on the page No. 5
I. ENGINE START 1. Set timer knob to the OFF position. Do not try to engine start a vehicle without a battery in it. You 2. With the charger unplugged from the AC outlet, connect the may damage the vehicle’s system. If the engine spins, but doesn’t charger to the battery following instructions given in section start after several starting attempts, there is a problem with the F. engine of the vehicle other than its starting system. STOP crank- 3. Plug the charger AC power cord into the AC outlet
Summary of the content on the page No. 6
L. ASSEMBLY INSTRUCTIONS First place the charger topside down on a flat surface. Wheel Charger assembly instructions: Next mount the mounting foot FIG. A with (2) 1/4-20 screws. NOTE: Unit must be fully assembled before operating Next pound the axle firmly into an axle cap using a hammer FIG B. PARTS: TOOLS NECESSARY: Next slide the wheels onto the axle, hubs must face in, FIG C. 2 10-32 thread cutting screws 3/8" wrench Next pound the other axle cap onto the other end of the axle. 2 1/4-20 thre
Summary of the content on the page No. 7
A. SEGURIDAD GENERAL DE ACUMULADORES 5. Quítese todos los artículos metálicos, tales como anillos, brazaletes, collares y relojes, al trabajar con un acumulador de ácido de plomo. 1. Antes de usar su cargador de acumuladores, lea todas las instrucciones Un acumulador de ácido de plomo puede producir un cortocircuito y precauciones impresas en: suficientemente fuerte para soldar un anillo (u otro objeto) a otro metal, el cargador de acumuladores causando así una quemada severa. el acumulador
Summary of the content on the page No. 8
E. INSTRUCCIONES DE FUNCIONAMIENTO: CARGA DE UN 3. Conecte la pinza POSITIVA (ROJA) del cargador al terminal POSITIVO ACUMULADOR EN UN VEHICULO (POS, P, +) del acumulador. Gire la pinza de ida y vuelta para hacer un buen contacto. Al cargar un acumulador en un vehículo, determine cuidadosamente 4. Colóquese a sí mismo y al extremo del cable aislado de 61cm tan lejos el tipo del acumulador y cuál es el terminal de tierra. Para reducir el como pueda del acumulador. Luego, conecte la pinza NEGATIVA
