Summary of the content on the page No. 1
Dell Vostro 3560
Owner's Manual
Regulatory Model: P24F
Regulatory Type: P24F001
Summary of the content on the page No. 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2012 Dell Inc. ™ ™ ™ ™ ™ ™ Trademarks used in this text: Dell , the Dell logo, Dell Precision , OptiPlex , Latitude , PowerEdge , PowerVault , ™ ™ ™ ™ ™ ™ ™ ™ Pow
Summary of the content on the page No. 3
Contents Notes, Cautions, and Warnings...................................................................................................2 1 Working on Your Computer.......................................................................................................5 Before Working Inside Your Computer.....................................................................................................................5 Recommended Tools...........................................................
Summary of the content on the page No. 4
Removing the Processor.........................................................................................................................................34 Installing the Processor..........................................................................................................................................35 Removing the Coin-Cell Battery..............................................................................................................................35 Installing the
Summary of the content on the page No. 5
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have performed the steps in Working on Your Computer. • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--in
Summary of the content on the page No. 6
6. Close the display and turn the computer upside-down on a flat work surface. NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9. Open the display. 10. Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display. CAUTION: Before touching anything inside your c
Summary of the content on the page No. 7
After Working Inside Your Computer After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers. 1. Connect any external devices, such as a port replicator, battery slice, or media base, and replace any cards, such as an ExpressCard. 2. Connect any telephone
Summary of the content on the page No. 8
8
Summary of the content on the page No. 9
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Removing the Security Digital (SD) Card 1. Follow the procedures in Before Working Inside Your Computer. 2. Press in on the SD card to release it from the computer. Slide the SD card out of the computer. Installing the Secure Digital Card 1. Push the SD card into the slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Co
Summary of the content on the page No. 10
Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer. Removing the ExpressCard 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery. 3. Press in on the ExpressCard and release. Pull the ExpressCard and remove out of the computer. Installing the ExpressCard 1. Push in the ExpressCard into the slot until it clicks into place. 2. Install the battery. 3. Follow the proced
Summary of the content on the page No. 11
4. Slide the cover outwards to release it from the notches on the computer. 5. Lift the cover upwards and away from the computer. 11
Summary of the content on the page No. 12
Installing the Base Cover 1. Align the edge of the base cover on the computer and slide it on the computer. 2. Tighten the screw(s) to secure the base cover to the computer. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer. Removing the Memory 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) battery b) base cover 3. Pry the retention clips away from the memory module until it pops-up. Lift and remove the memory module from i
Summary of the content on the page No. 13
4. Use a flat-headed screw driver to pry the optical drive out of the computer. 5. Slide the optical drive outwards and remove it from the computer. 6. Remove the screws that secure the optical-drive bracket. Remove the optical-drive bracket from the optical drive. 13
Summary of the content on the page No. 14
Installing the Optical Drive 1. Replace the optical-drive bracket and tighten the screws that secure the optical drive to the optical-drive bracket. 2. Slide the optical drive into the compartment on the chassis. 3. Tighten the screw to secure the optical drive to the computer. 4. Install the: a) base cover b) battery 5. Follow the procedures in After Working Inside Your Computer. Removing the Hard Drive 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) battery b
Summary of the content on the page No. 15
5. Lift up the hard drive and remove from the computer. 6. Remove the screws that secure the hard-drive bracket to the hard drive. 7. Lift up and remove the hard drive from the hard drive bracket. 15
Summary of the content on the page No. 16
Installing the Hard Drive 1. Place the hard drive module into the hard drive bracket. 2. Tighten the screws that secures the hard drive bracket to the hard drive. 3. Pull the tab and place the hard drive on the chassis. 4. Tighten the screws that secure hard drive to the computer. 5. Install the: a) battery b) base cover 6. Follow the procedures in After Working Inside Your Computer. Removing the Keyboard 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery. 3.
Summary of the content on the page No. 17
5. Lift the clip to release the keyboard cable and disconnect it from the system board. 6. Lift the clip to release the backlit cable and disconnect it from the system board. 17
Summary of the content on the page No. 18
Installing the Keyboard 1. Connect the keyboard data cable to the back of the keyboard. 2. Connect the backlit cable to the system board. 3. Insert the keyboard in its compartment. 4. Press down until the keyboard clicks into place. 5. Install the battery. 6. Follow the procedures in After Working Inside Your Computer. Removing the Display Hinge Cover 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the screws that secure the display-hinge cover to th
Summary of the content on the page No. 19
4. Push to release the hinge cover from the computer. 5. Flip the computer and carefully remove the display hinge cover from the computer. Installing the Display Hinge Cover 1. Replace the display hinge cover back to the computer till the latches are fixed into place. 2. Tighten the screws that secure the display hinge cover to the computer. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer. Removing the Palmrest 1. Follow the procedures in Before Working Ins
Summary of the content on the page No. 20
f) keyboard g) display hinge cover 3. Remove the rubber pads from the bottom of the computer. 4. Remove the screws from the bottom of the computer. 5. Disconnect the LEDs fingerprint cable. 20
