Summary of the content on the page No. 1
Dell ™ Vostro ™ V130 Service Manual
Regulatory Model: Regulatory Model: P16S
Summary of the content on the page No. 2
2
Summary of the content on the page No. 3
Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have performed the steps in Working on Your Computer. • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--inst
Summary of the content on the page No. 4
8. Turn the computer top-side up. 9. Open the display. 10. Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display. CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which
Summary of the content on the page No. 5
1. Connect any external devices, such as a port replicator, battery slice, or media base, and replace any cards, such as an ExpressCard. 2. Connect any telephone or network cables to your computer. CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 3. Replace the battery. 4. Connect your computer and all attached devices to their electrical outlets. 5. Turn on your computer. 5
Summary of the content on the page No. 6
6
Summary of the content on the page No. 7
Battery Removing The Battery 1. Follow the procedures in Before Working On Your Computer. 2. Remove the Secure Digital (SD) card. 3. Remove the base cover. 4. Lift the black cable-release clip to release the battery cable from the connector on the system board and disconnect the battery cable. 5. Remove the screws that secure the battery to the computer. 6. Lift the battery up and away from the computer. NOTE: To replace the battery, see Installing The Battery. 7
Summary of the content on the page No. 8
Installing The Battery NOTE: To remove or locate the battery, see Removing The Battery. 1. Place the battery into the battery bay. 2. Replace and tighten the screws that secure the battery to the computer. 3. Connect the battery cable to the system board and press down the cable-release clip to lock the battery cable. 4. Install the base cover. 5. Install the Secure Digital (SD) Card. 6. Follow the procedures in After working inside your computer. 8
Summary of the content on the page No. 9
Secure Digital (SD) Card Removing The Secure Digital (SD) Card 1. Follow the procedures in Before Working On Your Computer. 2. Press in on the SD card to release the SD card from the computer. 3. Slide the SD card out of the computer. 9
Summary of the content on the page No. 10
NOTE: To install the SD card, see Installing The Secure Digital (SD) card. Installing the Secure Digital (SD) Card NOTE: To remove or locate the Secure Digital card, see Removing the Secure Digital (SD) card. 1. Slide the SD card into its slot until it clicks into place. 2. Follow the procedures in After working inside your computer. 10
Summary of the content on the page No. 11
Base Cover Removing The Base Cover 1. Follow the procedures in Before Working On Your Computer. 2. Remove the Secure Digital (SD) Card. 3. Remove the screws that secure the base cover to the computer. 4. Slide the base cover towards the front of the computer. Lift it up and away from the computer. NOTE: To replace the base cover see, Installing The Base Cover. Installing The Base Cover NOTE: To remove or locate the base cover, see Removing The Base Cover . 1. Slide the base cover to align the sc
Summary of the content on the page No. 12
12
Summary of the content on the page No. 13
Hard Drive and Audio Board Removing The Hard Drive And Audio Board Assembly 1. Follow the procedures in Before Working On Your Computer. 2. Remove the Secure Digital (SD) card. 3. Remove the base cover. 4. Remove the battery. 5. Disconnect the speaker and system board cables from the audio board. 6. Remove the screws that secure the audio board and the hard drive to the computer. 7. Lift and remove the hard drive and audio board assembly from the computer. 13
Summary of the content on the page No. 14
8. Slide the audio board from the hard drive. 9. Remove the screws that secure the hard-drive bracket to the hard drive. 14
Summary of the content on the page No. 15
10. Remove the hard drive from the hard-drive bracket. NOTE: To install the audio board and the hard drive, see Installing The Hard Drive And Audio Board Assembly. Installing The Hard Drive And Audio Board Assembly To remove or locate the hard drive and audio board, see Removing The Hard Drive And Audio Board Assembly. 1. Attach the hard-drive bracket to the hard drive. 2. Tighten the screws to secure the hard-drive bracket to the hard drive. 3. Connect the audio board to the hard drive. 4. Tigh
Summary of the content on the page No. 16
16
Summary of the content on the page No. 17
Coin-Cell Battery Removing The Coin-Cell Battery 1. Follow the procedures in Before Working on Your Computer. 2. Remove the Secure Digital (SD) card. 3. Remove the base cover. 4. Remove the battery. 5. Remove the card-reader board. 6. Disconnect the coin-cell battery cable from the system board. 7. Release and remove the coin-cell battery from the computer. NOTE: To replace the coin-cell battery, see Installing The Coin-Cell Battery. Installing The Coin-Cell Battery NOTE: To remove or locate the
Summary of the content on the page No. 18
2. Connect the coin-cell battery cable to the system board. 3. Install the card-reader board. 4. Install the battery. 5. Install the base cover. 6. Install the secure digital (SD) card. 7. Follow the procedures in After working inside your computer. 18
Summary of the content on the page No. 19
Wireless Local Area Network (WLAN) Card Removing The Wireless Local Area Network (WLAN) Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the Secure Digital (SD) card. 3. Remove the base cover. 4. Remove the battery. 5. Disconnect the antenna cables from the WLAN card. 6. Remove the screw that secures the WLAN card to the computer. 7. Slide and remove the WLAN card out from its slot on the system board. NOTE: To install the WLAN card, see Installing The Wireless Local A
Summary of the content on the page No. 20
Installing The Wireless Local Area Network (WLAN) Card NOTE: To remove or locate the WLAN card, see Removing The Wireless Local Area Network (WLAN) Card. 1. Insert the WLAN card into its connector at a 45–degree angle. 2. Replace and tighten the screw that secures the WLAN card to the computer. 3. Connect the black and white antenna cables to their respective connectors marked on the WLAN card. 4. Install the battery. 5. Install the base cover. 6. Install the Secure Digital (SD) card. 7. Follow
