Summary of the content on the page No. 1
Dell Latitude 10 – ST2e
Owner's Manual
Regulatory Model: T05G
Regulatory Type: T05G001
Summary of the content on the page No. 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2013 Dell Inc. ™ ™ ™ ™ ™ ™ Trademarks used in this text: Dell , the DELL logo, Dell Precision , Precision ON ,ExpressCharge , Latitude , Latitude ON , ™ ™ ™ ® ® ®
Summary of the content on the page No. 3
Contents Notes, Cautions, and Warnings...................................................................................................2 1 Working on Your Computer.......................................................................................................5 Before Working Inside Your Computer.....................................................................................................................5 Turning Off Your Computer...................................................
Summary of the content on the page No. 4
Running the ePSA Diagnostic Utility.......................................................................................................................27 Beep Codes.............................................................................................................................................................29 LED Error Codes......................................................................................................................................................30 5 Spe
Summary of the content on the page No. 5
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have performed the steps in Working on Your Computer. • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--in
Summary of the content on the page No. 6
NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9. Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display. CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of t
Summary of the content on the page No. 7
NOTE: It is recommended that you immediately backup the operating system image using the USB device through Dell Backup and Recovery (DBAR) application. 7
Summary of the content on the page No. 8
8
Summary of the content on the page No. 9
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • #0 Phillips screwdriver • #1 Phillips screwdriver • Small plastic scribe Internal View Figure 1. Internal View 1. system board 3. rear camera 2. front camera 4. battery 9
Summary of the content on the page No. 10
5. volume button 9. coin-cell battery 6. speaker 10. speaker 7. battery 8. docking board Removing the Base Cover 1. Follow the procedures in Before Working Inside Your Computer. 2. Pry and lift the base cover from the computer by following the arrow sequence in the diagram. Installing the Base Cover 1. Attach the base cover to the computer. 2. Follow the procedures in After Working Inside Your Computer. Removing the Battery 1. Follow the procedures in Before Working Inside Your Computer. 2. Remo
Summary of the content on the page No. 11
Installing the Battery 1. Tighten the screws to secure the battery to the computer. 2. Install the base cover. 3. Follow the procedures in After Working Inside Your Computer. Removing the Front Camera 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) base cover b) battery 3. Lift up the connector latch and disconnect the camera cable. Remove the screw that secures the camera module to the computer. Remove the camera module from the computer. 11
Summary of the content on the page No. 12
Installing the Front Camera 1. Place the camera module in its slot on the computer. 2. Tighten the screw to secure the camera module to the computer. 3. Connect the camera cable to the connector. 4. Install the: a) battery b) base cover 5. Follow the procedures in After Working Inside Your Computer. Removing the Speakers 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the : a) base cover b) battery 3. Lift up the coin-cell battery from its slot and un-route it's cablin
Summary of the content on the page No. 13
5. Un-route the speaker cable on the side of the computer and lift it up to release the speaker from the computer. 6. Un-route the speaker cable on the side of the computer and lift it up to release the speaker from the computer. 13
Summary of the content on the page No. 14
Installing the Speakers 1. Place the right and the left speakers in their slot. 2. Route the speaker cables on the chassis. 3. Tighten the screws to secure the speakers to the chassis. 4. Place the coin-cell battery in its slot and route the cables. 5. Connect the speaker connector cable to its port on the system board. 6. Install the : a) battery b) base cover 7. Follow the procedures in After Working Inside Your Computer. Removing the Docking Board 1. Follow the procedures in Before Working In
Summary of the content on the page No. 15
4. Remove the screws that secure the docking board to the computer. 5. Remove the docking board from the computer and disconnect the home-button board cable. Installing the Docking Board 1. Connect the home-button board cable to the docking board and place the docking board in its slot in the computer. 2. Tighten the screws to secure the docking board to the computer. 3. Connect the docking-board power cable to the connector. 4. Install the: a) front camera b) speaker c) battery d) base cover 5.
Summary of the content on the page No. 16
Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) base cover b) battery c) speaker d) front camera e) docking board 3. Disconnect the LVDS and docking board cables. 4. Remove the screws that secure the system board to the computer. 5. Lift up the system board at a 45° angle and pull it away from the computer. Installing the System Board 1. Place the system board in its compartment on the computer. 2. Tighten the screws to secure the syst
Summary of the content on the page No. 17
4. Install the: a) docking board b) front camera c) speaker d) battery e) base cover 5. Follow the procedures in After Working Inside Your Computer. Removing the Rear Camera 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) base cover b) battery c) speaker d) front camera e) system board 3. Remove the camera module from the system board. Installing the Rear Camera 1. Place the camera module in its slot on the system board. 2. Install the: a) system board b) front
Summary of the content on the page No. 18
Removing the Coin-Cell Battery 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) base cover b) battery c) speaker d) front camera e) system board 3. Disconnect the coin-cell battery cable and remove it from the computer. Installing the Coin-Cell Battery 1. Connect the coin-cell battery cable to the system board. 2. Install the: a) system board b) front camera c) speaker 3. Replace the coin-cell battery in its slot on the computer. 4. Install the: a) battery b) ba
Summary of the content on the page No. 19
b) battery 3. Disconnect the volume-board cable from the connector. Lift up and remove the volume-board cable from the system board. 4. Pry the sides of the volume-button board with a flat-head screw driver to loosen it from it's slot on the computer. Remove the volume-button board from the computer Installing the Volume-Button Board 1. Place the volume-button board in it's slot on the computer. 2. Route and connect the volume-board cable to the connector. 3. Install the: a) battery b) base co
Summary of the content on the page No. 20
20
