Summary of the content on the page No. 1
®
A Division of Cisco Systems, Inc.
Wireless-G
IP Phone
User Guide
Voice
Model No.
WIP330
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Wireless-G IP Phone Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. WARNING: This product contains chemicals, including lead, known to the State of California to cause cancer,
Summary of the content on the page No. 4
Wireless-G IP Phone Table of Contents Chapter 1: Introduction 1 Welcome 1 What’s in This User Guide? 1 Chapter 2: Getting to Know the Wireless-G IP Phone 3 The Bottom Panel 3 The Front and Side Panels 4 The Back Panel 6 Chapter 3: Installing and Using the Wireless-G IP Phone 7 Overview 7 Inserting the Battery into the Wireless-G IP Phone 7 Powering on the Wireless-G IP Phone 8 Setting up the Wireless-G IP Phone 10 Using the Wireless-G IP Phone 19 Chapter 4: Configuring the Wireless-G IP Phone 21
Summary of the content on the page No. 5
Wireless-G IP Phone List of Figures Figure 2-1: Bottom Panel 3 Figure 3-21: Save Password 17 Figure 2-2: Front Panel 4 Figure 3-22: Save SIP Settings 17 Figure 2-3: Side Panel 5 Figure 3-23: Return to Standby Screen 18 Figure 2-4: Back Panel 6 Figure 3-24: Standby Screen 18 Figure 3-1: Press the Button 7 Figure 3-25: Call Connected 19 Figure 3-2: Insert the Battery 7 Figure 3-26: Line Options 19 Figure 3-3: Connect the Power 8 Figure 3-27: Second Call 20 Figure 3-4: Front Panel 9 Figure 4-1: Fro
Summary of the content on the page No. 6
Wireless-G IP Phone Figure 4-18: Network Settings - Fixed IP 29 Figure 4-44: Wi-Fi Profiles 37 Figure 4-19: Enter IP Address 29 Figure 4-45: Select SSID 38 Figure 4-20: Select Subnet Mask 29 Figure 4-46: Enter SSID 38 Figure 4-21: Enter Subnet Mask 29 Figure 4-47: Change Wireless Mode 38 Figure 4-22: Select Phone Settings 30 Figure 4-48: Change Authentication Mode 38 Figure 4-23: Phone Settings 30 Figure 4-49: Change Transmit Key 39 Figure 4-24: Ring Options 30 Figure 4-50: Edit WEP Key 39 Figur
Summary of the content on the page No. 7
Wireless-G IP Phone Chapter 1: Introduction Welcome Thank you for choosing the Linksys Wireless-G IP Phone. It will allow you to make phone calls using your ip (internet protocol): a protocol used to broadband connection, whether you are at home, in your office, or at a public hotspot. send data over a network. How does the IP Phone do this? It connects to your wireless router or gateway, so telephone service is delivered through your cable or DSL Internet connection. You can also surf the Int
Summary of the content on the page No. 8
Wireless-G IP Phone Chapter 2: Getting to Know the Wireless-G IP Phone This chapter describes the physical features of the IP Phone. Chapter 3: Installing and Using the Wireless-G IP Phone This chapter explains how to install the IP Phone and use it. Chapter 4: Configuring the Wireless-G IP Phone This chapter discusses how to configure the IP Phone’s settings. Appendix A: Troubleshooting This appendix describes some potential problems and solutions, as well as frequently asked questions,
Summary of the content on the page No. 9
Wireless-G IP Phone Chapter 2: Getting to Know the Wireless-G IP Phone The Bottom Panel The IP Phone’s headset jack and USB port are located on the bottom panel. Headset USB Port Jack Figure 2-1: Bottom Panel Headset Jack This jack allows you to connect a headset. USB Port The USB port allows you to attach the included power adapter. Chapter 2: Getting to Know the Wireless-G IP Phone 3 The Bottom Panel
Summary of the content on the page No. 10
Wireless-G IP Phone Power LED The Front and Side Panels The power LED is located at the top of the IP Phone, while its buttons are located on the front and side panels. Power LED Blue/Purple. The LED lights up blue when the IP Phone is powered on and ready. It flashes, alternating between blue and purple, when the IP Phone is re-charging. When the IP Phone is fully charged and still connected to its power adapter, the LED will be a solid purple. When the IP Phone is charged and not connected
Summary of the content on the page No. 11
Wireless-G IP Phone Icon Button Name Function Power On/Off or Press and hold this button for End Call two seconds to power the IP Phone on or off. Speakerphone Ends the call or exits the current menu Speakerphone Switches to speakerphone Volume (The speaker is located on the back of the IP Phone) Volume Raises or lowers the volume Figure 2-3: Side Panel Chapter 2: Getting to Know the Wireless-G IP Phone 5 The Front and Side Panels
Summary of the content on the page No. 12
Wireless-G IP Phone The Back Panel The IP Phone’s speaker (for the speakerphone feature) and battery compartment are located on the back panel of the IP Phone. (The speaker is controlled by the speakerphone button on the side panel. For directions on how to insert the battery, refer to “Chapter 3: Installing and Using the Wireless-G IP Phone.” Speaker Battery Compartment Figure 2-4: Back Panel 6 Chapter 2: Getting to Know the Wireless-G IP Phone The Back Panel
Summary of the content on the page No. 13
Wireless-G IP Phone Chapter 3: Installing and Using the Wireless-G IP Phone Overview This chapter provides instructions for first-time installation and use of the IP Phone. You will insert the battery Metal Contacts into the IP Phone and then set it up for your wireless network and Internet phone service. Then you will be able to make and receive Internet phone calls. Inserting the Battery into the Wireless-G IP Phone To insert the battery, follow these instructions: 1. Remove the cover of the
Summary of the content on the page No. 14
Wireless-G IP Phone Powering on the Wireless-G IP Phone Make sure you have the account information, including necessary IP Phone settings, supplied by your Internet phone service provider. If you already have an account set up with your Internet phone service provider, then proceed to step 1. If you do not have an account, then go to the website of your Internet phone service provider and sign up for service. After you have set up an account, proceed to step 1. 1. Make sure you have the accou
Summary of the content on the page No. 15
Wireless-G IP Phone Power LED 3. The power LED will flash, alternating between blue and purple. For the initial charge, allow the battery to charge for at least 10 hours, so the battery will have a full charge, which is indicated by a solidly lit Power LED. This maximizes battery performance and life. When the battery is fully charged, proceed to “Setting up the Wireless-G IP Phone.” Navigation Pad Softkey Softkey and Center Power On/Off Selection Key Call or End Call Figure 3-4: Front Panel
Summary of the content on the page No. 16
Wireless-G IP Phone Setting up the Wireless-G IP Phone Before you begin, make sure your network has an active Internet connection. 1. Press and hold the Power On/Off button for two seconds. 2. The IP Phone will boot up and automatically scan for wireless networks. Figure 3-5: Scan for Wireless Networks 3. A list of wireless networks will be displayed and show their wireless network names (also known as Service Set Identifier or SSID), security status (a lock indicates wireless security), and s
Summary of the content on the page No. 17
Wireless-G IP Phone 4. The IP Phone will automatically connect to the network you have selected. If security is enabled on the selected network, a new screen will appear. Using the navigation pad, select the appropriate transmit key number and then move to the WEP Key field. Enter the network’s WEP key. Select Exit to save your changes, or select Clear to delete a character or number. Figure 3-7: Connect to Figure 3-8: Enter WEP Wireless Network Key (for Secured Networks) 5. You will be not
Summary of the content on the page No. 18
Wireless-G IP Phone 6. The standby screen will appear. Select Menu. Figure 3-10: Select Menu 7. Phone Settings will be highlighted. Navigate the menu choices, and then select SIP Settings. (SIP stands for Session Initiation Protocol.) Figure 3-11: Select SIP Settings 12 Chapter 3: Installing and Using the Wireless-G IP Phone Setting up the Wireless-G IP Phone
Summary of the content on the page No. 19
Wireless-G IP Phone 8. A list of SIP settings will be displayed. For the Proxy IP setting, select Edit. NOTE: The Proxy IP address and other information should have been supplied by your Internet phone service provider. If you do not have this information, contact your Internet phone service provider. Figure 3-12: Edit Proxy IP 9. Enter the Proxy IP address in the new window, and then select Save. Figure 3-13: Save Proxy IP Chapter 3: Installing and Using the Wireless-G IP Phone 13 Setting u
Summary of the content on the page No. 20
Wireless-G IP Phone 10. Scroll down to Proxy Port, and select Edit. 11. Enter the Proxy Port number address in the new window, and then select Save. Figure 3-14: Save Proxy Port 12. Scroll down to Register Proxy IP, and select Edit. 13. Enter the Register Proxy IP address in the new window, and then select Save. Figure 3-15: Save Register Proxy IP 14 Chapter 3: Installing and Using the Wireless-G IP Phone Setting up the Wireless-G IP Phone
