Summary of the content on the page No. 1
®
Planet Light
PL04
®
Energy Saving Natural Spectrum
Floor Lamp
Summary of the content on the page No. 2
Dear Customer, ® Thank you for purchasing the Planet Light Energy ® Saving Natural Spectrum Floor Lamp. You have received a quality product, backed by a one-year limited warranty. As a Verilux customer, your satisfaction means everything to us. We look forward to serving you now and in the future. Many other healthy lighting products are available through our catalog and online. Visit us on the web at www.verilux.com to request a free catalog and learn more about all our quality Verilux
Summary of the content on the page No. 3
Important Safety Instructions SAVE THESE INSTRUCTIONS ® Thank you for purchasing the Planet Light Energy Saving Natural ® Spectrum Floor Lamp. Please read the following safety information before using. To reduce the risk of fire, electrical shock or injury to persons: • Do NOT dismantle. • Do NOT alter power cord. • Turn off/unplug and allow to cool before replacing bulb or cleaning. Warnings and Precautions • For indoor use only. • The lamp is an electrical device. DO NOT USE NEAR WATER. •
Summary of the content on the page No. 4
Avertissements et Précautions • Pour usage intérieur seulement. • La lampe est un dispositif électrique. NE PAS UTILISER PRÈS DE L’EAU. • Avant de brancher la lampe, vérifier que la tension de la prise murale ne dépasse pas 120 volts. • Ne pas utiliser avec des gradateurs de lumière, des minuteries, des détecteurs de mouvement ou des rallonges. • Ce produit peut causer des interférences avec des radios, des téléphones sans fil ou des appareils utilisant une télécommande sans fil, telle qu’u
Summary of the content on the page No. 5
Getting Star HEADER ted Main Parts & Controls F. Polarized Plug A. Lamp Head G. Bulb B. Gooseneck H. High/Off/Low Switch C. Shaft D. Lamp Base E. Power Cord Close-up of Lamp Head A B G H C E D F CAUTION: DO NOT LIFT THE LAMP BY THE GOOSENECK. THE LAMP SHOULD BE LIFTED BY THE SHAFT. MISE EN GARDE : NE PAS SOULEVER LA LAMPE PAR SON COL-DE-CYGNE. LA LAMPE DOIT ÊTRE SOULEVÉE PAR LA TIGE. 5
Summary of the content on the page No. 6
Unpacking Y HEADER our Lamp 1. Remove all pieces from box. Locate the two Phillips head screws. 2. Detach the red plastic protective pieces and store them in the event you need to return the lamp. 3. Important: To avoid scratching the metal shaft, do not use a sharp object to cut the plastic covering. The clear plastic covering on the shaft is specially designed to tear away easily. IMPORTANT NOTE: Remove red plastic protective pieces prior to assembly. 6
Summary of the content on the page No. 7
Assembly Instructions HEADER Read Instructions Carefully Before Assembly: 1. Connect the two ends of the Power Cord (between the Base and the Shaft) using the lock connectors. 2. Carefully tuck excess Power Cord into the Shaft. DO NOT CUT OR SHORTEN THE POWER CORD. 3. Insert the Gooseneck and the Shaft into the Base. 4. Check direction of the lamp and the hole on the Base, then use a Phillips Head Screwdriver (not included) to tighten the screw into the hole. CAUTION: BE VERY CAREFU
Summary of the content on the page No. 8
Assembly Instructions cont. HEADER 5. To prevent damage during shipping, the Verilux bulb is surrounded by protective padding. Carefully remove and dispose of the protective padding. Check to ensure that the bulb is fully seated and has not come loose from the socket during shipping. There should be no gap between the bulb and socket. 6. Plug lamp into outlet and turn on. If bulb does not illuminate instantly, please refer to the troubleshooting section of this manual. 8
Summary of the content on the page No. 9
Bulb Replacement Instructions HEADER Installation 1. Unplug lamp from power source. C 2. Firmly hold the base (B) and push bulb (C) into the socket (A). 3. Be sure the bulb is firmly seated in the socket (see below) and snapped into the metal bulb clip (D). B A Removal C 1. Unplug the lamp from the power source. 2. Firmly hold the bulb base (B) and pull the bulb (C) from the socket (A) in an outward motion. B A YES NO D Notice No large gap gap Correctly seated bulb Incorrectly seated bu
Summary of the content on the page No. 10
Troubleshooting HEADER ® Before requesting service on your Verilux lamp, please read the following: • Make sure all power connectors, cords and plugs are inserted fully and securely. • Be sure the bulb is securely seated into the socket (see page 9). • Make sure there is power to the wall outlet or try another outlet. • CAUTION: DISCONNECT LAMP BEFORE PERFORMING ALIGNMENT ACTIVITY. MISE EN GARDE : DÉBRANCHER LA LAMPE AVANT D’EFFECTUER SON ALIGNEMENT. Correct alignment with screw holes can
Summary of the content on the page No. 11
Care & Cleaning HEADER Your lamp is made from high quality materials that will last for many years with minimum care. You may want to periodically clean the lamp using a mild non-abrasive cleaner and soft cloth. When cleaning, make sure you have turned off and unplugged the unit, allowing sufficient time for the unit to cool. All liquid should be properly wiped away and dried prior to restoring power. CAUTION: DO NOT USE SOLVENTS OR CLEANERS CONTAINING ABRASIVES, OR AMMONIA BASED CLEANERS.
Summary of the content on the page No. 12
One Year Limited Warranty ATTENTION! ONCE OPENED, PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED FOR REPAIR OR REPLACEMENT! Many questions may be answered by visiting www.verilux.com, or you may call our Customer Service Department at 800-786-6850 during normal business hours. This limited warranty is provided by: Verilux, Inc., 340 Mad River Park, Waitsfield, VT 05673 Verilux warrants this product to be free from defects in material and workmanship for a period of one
