Summary of the content on the page No. 1
Owner’s Manual
™
SmartRack Accessories
Model: SRCABLELADDER
1 – Introduction 2
1-1 Parts List
2
1-2 Tools Required
2
2 – Important Safety Instructions 2
3 – Installation
3
3-1 Planning 3
3-2 Ladder Modification (Optional)
4
3-3 Ladder Assembly 4
3-4 Installation Across Aisle
5
3-5 Installation Within Row 6
3-6 Ground Connection
7
4 – Storage and Service
8
5 – Warranty and Warranty Registration
8
1111 W. 35th Street, Chicago, IL 60609 USA
+1.773.869.1234 • www.tripplite.com
Copyright © 2008 Tripp
Summary of the content on the page No. 2
1 – Introduction SRCABLELADDER provides roof-mounted cable routing for Tripp Lite’s SmartRack Enclosures, allowing cable bundles to span aisles and/or spaces between enclosures in the same row. Note: Standard installation of SRCABLELADDER requires Tripp Lite’s SRCABLETRAY accessory, sold separately. 1-1 Parts List A Ladder Sections (2) A D G B Assembly Brackets (6) C Clevis Pins (12) D Cotter Pins (12) B E H E Ground Brackets (2) F M6 Hex-Head Bolts (2) C F I G 24-inch Ground Cables (3) H M6
Summary of the content on the page No. 3
3 – Installation Note: Prior to installation, you must install the SRCABLETRAY accessory (sold separately) on each enclosure that will be linked by the SRCABLELADDER accessory. For ordering information, call Tripp Lite Customer Service at +1.773.869.1234. 3-1 Planning SRCABLELADDER can provide enclosure-to-enclosure cable routing across an aisle or within a single row. You can combine multiple SRCABLELADDER and SRCABLETRA Y accessories to meet the cable routing needs of almost any configura
Summary of the content on the page No. 4
3 – Installation (continued) 3-2 Ladder Modification (Optional) Warning: When using tools to cut or drill metal, use eye protection and follow all other safety precautions recommended by the tool manufacturer and required by applicable safety regulations. Use caution and wear safety gloves when handling metal parts that have been cut to length. Sharp edges can cause personal injury and property damage. Note: Do not modify the SRCABLELADDER accessory unless you have followed the instructions in
Summary of the content on the page No. 5
3 – Installation (continued) 3-4 Installation Across Aisle Note: Follow the instructions in this section only if the SRCABLELADDER accessory will be installed across an aisle. If the SRCABLELADDER accessory will be installed within a row of enclosures, follow the instructions in Section 3-5 Installation Within Row instead. A 1 Insert four assembly brackets into the ends of the ladder. The hooked ends of the brackets should be exposed. When the ladder is oriented so that the ladder’s rungs
Summary of the content on the page No. 6
3 – Installation (continued) 3-5 Installation Within Row Note: Follow the instructions in this section only if the SRCABLELADDER accessory will be installed within a row of enclosures. If the SRCABLELADDER accessory will be installed across an aisle, follow the instructions in Section 3-4 Installation Across Aisle instead. 1 A Insert four assembly brackets in the open ends of the ladder, hooked end first. When the ladder is oriented so that the ladder ’ s rungs are above the ladder’s side
Summary of the content on the page No. 7
3 – Installation (continued) 3-5 Installation Within Row (continued) G 6 After inserting the clevis pins, insert a cotter pin through the hole at the end of each clevis pin. (The straight section of the G cotter pin goes through the hole.) 6 3-6 Ground Connection After installing the SRCABLELADDER accessory, determine 1 where to place ground brackets by noting the distance between A one end of the ladder and the grounding post at the corner of the nearest SRCABLETRAY accessory. A 1 B 2 P
Summary of the content on the page No. 8
4 – Storage and Service Storage The unit must be stored in a clean, secure environment with a temperature less than 40° C (104° F) and a relative humidity less than 90% (non-condensing). Store the unit in its original shipping container if possible. Service The unit is covered by the limited warranty described in this manual. For more information, call Tripp Lite Customer Service at +1.773.869.1234. 5 – Warranty and Warranty Registration Limited Warranty Seller warrants this product, if use
