Summary of the content on the page No. 1
INSTALLATION INSTRUCTIONS
AM3/AM3-B
Universal Swingout Arm
AUSTRALIA, NEW ZEALAND, OCEANIA
EUROPE
NORTH AMERICA (DISTRIBUTOR)
3130 East Miraloma Avenue
Swallow House,
P.O. Box 295
Anaheim, CA 92806 USA
Shilton Industrial Estate,
Mordialloc Victoria 3195
USA and Canada –
Shilton, Coventry, England CV79JY
Australia
Phone: 800-368-9700
Phone: +44 (0) 2476 614700
Phone: 039586 6330
Fax: 800-832-4888
Fax: +44 (0) 2476 614710
www.premiermounts.com.au
Other Locations – Phone: (001)-714-632-7100; Fax:
Summary of the content on the page No. 2
AM3/AM3-B Table of Contents Warning Statements 2 Parts List 3 Installation Tools 3 Thread Depth Indicator 6 Mount Orientation 7 Mount Installation 8 Concrete Installation 8 Nose Piece Orientation 9 Universal Mounting Bracket Assembly 10 Attaching the Display 11 Securing the Display 12 Tilt Positioning 13 Cable Access Holes 13 Technical Specifications 14 Warranty 15 W
Summary of the content on the page No. 3
AM3/AM3-B Parts List This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700). AM3 Swingout Arm (Qty 1) AM3 Universal Barcket Arms (Qty 2) Griplate™ (Qty 8) 5/16” Flat Washers (Qty 6) 5/16” x 3” Lag Bolts - wooden studs only (Qty 6) Installation Tools Pencil 1/
Summary of the content on the page No. 4
AM3/AM3-B (Qty 8) M4 x 16 (Qty 8) M6 x 30 (Qty 8) M4 x 25 (Qty 8) M6 x 45 (Qty 8) M5 x 12 M8 x 20 (Qty 8) (Qty 8) M5 x 16 (Qty 8) M5 x 20 (Qty 8) M8 x 25 (Qty 8) M5 x 25 M8 x 30 (Qty 8) M5 x 50 (Qty 8) M8 x 35 (Qty 8) (Qty 8) M6 x 16 (Qty 8) M6 x 20 (Qty 8) M8 x 45 M8 x 70 (Qty 4) Page 4 Installation Instructions
Summary of the content on the page No. 5
AM3/AM3-B The nylon spacers may be stacked to achieve proper spacing. 9/16" Nylon spacers 1/4" Nylon spacers (large) (Qty 8) (Qty 8) 1/2" Nylon spacers Nylon sleeves (large) (Qty 8) (Qty 12) 5/16" Flat washers (metal) (Qty 8) 1" Nylon Spacers (Qty 8) 1/4" Nylon spacers (small) (Qty 8) Installation Instructions Page 5
Summary of the content on the page No. 6
AM3/AM3-B Thread Depth Indicator 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the fl at panel to make sure the inserts measure the same full depth and mark it (Figure 1). 2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied). 3. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw. 4. The screw length must not bypass the marking. S
Summary of the content on the page No. 7
AM3/AM3-B Mount Orientation The AM3/AM3-B Plasma Mount has the built-in capability of mounting with the swingout arm on either the left or right-hand side. WHEN MOUNTING THE AM3, THE SIDE THAT THE SWINGOUT ARM IS LOCATED ON MUST HAVE A LAG BOLT MOUNTED ON AT LEAST ONE SIDE (SEE FIGURE 1), TOP AND BOTTOM. Step 1. To change the mount orientation, choose the desired side that the mount will open to, left or right. Step 2. Once the side has been determined, attach the mount to the wall. Wood Studs
Summary of the content on the page No. 8
AM3/AM3-B Mount Installation Before proceeding with the mount installation, you should already have the mounting holes pre-drilled. Please use the template (supplied) and follow the instructions. For ease of installation, it is recommended that two people perform the installation. WHEN MOUNTING THE AM3, THE SIDE THAT THE SWINGOUT ARM IS LOCATED ON MUST HAVE A LAG BOLT MOUNTED ON AT LEAST ONE SIDE ( FIGURE 4, PAGE 8), TOP AND BOTTOM. DO NOT OVERTIGNTEN THE LAG BOLTS WHEN ATTACHING THE MOUNT
Summary of the content on the page No. 9
AM3/AM3-B Nose Piece Orientation Rotate Nose 180° Right Side Orientation Left Side Orientation Figure 7 Tension Bolts Tension Bolts Back Side of Nose Piece Front Side of Nose Piece Figure 8 Step 1. Once the mount has been oriented and mounted to the wall, remove the nose piece by removing the tensions bolts. After loosening the tension bolts, be sure that the nose piece is held together tightly before rotating. Step 2. Detach the nose piece assembly, rotate 180°, and place back onto the mou
Summary of the content on the page No. 10
AM3/AM3-B Universal Mounting Bracket Assembly Step 1. Place the universal bracket bar and the universal brackets on a flat surface. Step 2. Slide the universal brackets onto the universal bracket bar (as shown in Figure 9) with the set screws facing up. At this time, do not tighten the set screws that are located on the universal bracket. Step 3. Place the display on a soft, flat surface, face-down. Next, place the universal bracket assembly on the back of the display, with the universal brack
Summary of the content on the page No. 11
AM3/AM3-B Attaching the Display ONCE THE UNIVERSAL BRACKET BAR ASSEMBLY HAS BEEN ATTACHED TO THE DISPLAY, IT IS RECOMMENDED THAT TWO PEOPLE MOUNT THE DISPLAY, AS THE UNIT IS HEAVY AND, IF DROPPED, WILL DAMAGE THE MOUNT, THE DISPLAY, AND/OR PERSONNEL. Universal Bracket Swingout Arm Nose Piece Universal Bracket Bar Display Figure 10 Figure 11 Step 1. Slide the display assembly onto the nose piece of the swingout arm. Figure 13 Figure 12 Step 3. Use the M6 x 12mm Phillips Head screw to Step 2
Summary of the content on the page No. 12
AM3/AM3-B Securing the Display Once the two units have been secured together, the two (2) M6 x 30mm Phillips Head locking screws must be installed in the noted location (Figure 14) to prevent any movement. Universal Bracker Bar M6 x 30mm Phillips Head Screw (Attached) M6 x 30mm Phillips Head AM3/AM3-B Screw Nose Piece Swingout Arm Figure 14 Page 12 Installation Instructions
Summary of the content on the page No. 13
AM3/AM3-B Tilt Positioning To adjust the display, loosen the tension bolts no more than ½ turn, make the adjustments and then tighten the tension bolts. When tilt positioning is needed to adjust the display, place a hand at the top corner of the display and the other hand at the bottom of the display (Figure 15). To Tilt the Display Gently push both hands inward. This motion will cause the display to tilt forward. To Tilt the Display Back Gently push both hands outward. This motion will ca
Summary of the content on the page No. 14
AM3/AM3-B Technical Specification All measurements are in inches(mm). Page 14 Installation Instructions
Summary of the content on the page No. 15
AM3/AM3-B Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defectiv
