Fisher-Price 79652 user manual

Summary of the content on the page No. 1

Bounce ‘n Play
Activity Dome
Model Number: 79652
Please keep this instruction sheet for future reference,
as it contains important information.
Tool needed for assembly: Phillips Screwdriver (not included).
Use only for a child who is unable to push up on hands and knees,
pull up or sit unassisted.
Product features may vary from picture above.
w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m

Summary of the content on the page No. 2

Warnings Consumer Information Occasionally a consumer may experience WARNING a problem with one of our products. If this should happen, please call us toll-free, rather than return this product to the store. Failure to follow these warnings Usually, we can solve the problem over the telephone and instructions could result in or send you replacement parts. serious injury or death. Please call Fisher-Price® Consumer Relations, toll-free at 1-800-432-KIDS, To reduce the risk of Sudden Infant 8 AM

Summary of the content on the page No. 3

® ® Parts Metal Canopy Stay Pad 2 Covers 1 1 3 Toys (Toys may be different than shown.) 2 Base Wires Base Spring - 4 Plastic Mesh Cover Stay 13 16 M5 x 1 / " Screw - 2 CAUTION 5 M6 x 1 /8" Screw - 8 This product contains small parts in its unassembled state. Adult assembly is required. M5 Lock Nut - 2 M6 Lock Nut - 8 ALL SHOWN ACTUAL SIZE 3

Summary of the content on the page No. 4

Assembly IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Frame Button Hole Middle Hole Middle Hole Plastic Mesh Cover Stay Mesh Cover 3 Frame Tubes • Position the ends of the frame tubes against the middle 1 holes in a frame. Base Rounded Side • Open the base and position it up

Summary of the content on the page No. 5

Assembly Frame 5 • Tighten the screws with a Phillips screwdriver. Do not over-tighten. • Repeat assembly steps 3 - 5 to attach the other ends of the frame tubes to the frame on the other side of the base. 7 Rounded Side • Fit an M6 lock nut (with the M6 Lock Nut - 4 rounded side toward the 5 M6 x 1 /8" Screw - 4 Spring - 4 fabric) into each lower,hexag- onal opening on the back of the frame. • Tighten the screws with a Phillips screwdriver. Do not over-tighten. • Repeat this procedure to at

Summary of the content on the page No. 6

® Assembly Toys Canopy Rounded Fasteners Side 13 M5 x 1 /16" Screw -2 M5 Lock Nut -2 Pad Fastener Metal Canopy Stay Cover Upper 9 Hole • Fasten the pad fasteners to the base fasteners. 8 • Lift the canopy. Slot Tab • Attach the toys to the canopy fasteners. IMPORTANT! Assembly is now complete, but Bounce ‘n Play Activity Dome is not ready for use. Please refer to the Use instructions, on this page, beginning with step 2. • Position one end of the metal canopy stay against the upper hole in a fra

Summary of the content on the page No. 7

® Use To Unfold PUSH PUSH Frame Groove 1 Base Wire 3 Sides of Base Wire • Position the product upright on a flat surface. • Push down on the product to be • Grasp both sides of a base wire. sure each side of the base wire is • Pull both sides of the base wire outward and then let the in the correct position. The base base wire rotate down. wire should rest in the groove in Note: If the base wire does not freely rotate down, pull the each frame. CORRECT sides of the base wire further outward. • R

Summary of the content on the page No. 8

® Use Use Using the Mesh Cover Base Wire Zipper Mesh Cover Up Canopy Up 7 5 • Rotate the base wire up. • Repeat this procedure to fold the other base wire. • Adjust the canopy and mesh cover up. • While holding the mesh cover up, fasten the zipper closed. Care To Fold for Portability The pad and toys are machine washable. Wash the pad and toys separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The fabric and frame may be wiped