Summary of the content on the page No. 1
PURIST/PURIST with Mood Lighting
INSTALLATION INSTRUCTIONS
IMPORTANT
ALL INSTALLATIONS MUST COMPLY WITH COUNCIL AND LOCAL
AUTHORITYBYLAWS. IT IS THE RESPONSIBILITY OF THE PLUMBER TO
ENSURE THAT THE WASTE IS MADE WATERTIGHT BY MEANS OF SILICONE
SEALANT OR CAULKINGCOMPOUND. PLEASE PROVIDE MOTOR ACCESS
FOR SERVICING.
Instructions, drawings, and diagrams contained in this manual
present information available at the time of printing. Although
every attempt has been made to keep them up-to-da
Summary of the content on the page No. 2
TABLE OF CONTENTS Page 1.0 INTRODUCTION. 3 1.1 PRODUCT INFORMATION 3 1.2 WHIRLPOOL IDENTIFICATION 3 1.3 SPECIFICATIONS 3 2.0 INSTALLATION 4 2.1 PRODUCT INSPECTION 4 2.2 ACCESS PANEL 4 2.3 WHIRLPOOL INSTALLATION 5 2.4 TAPWARE AND DRAIN INSTALLATION 5 2.5 ELECTRICAL CONNECTIONS 6 2.6 TESTING 6 3.0 OPERATION 7 3.1 EFFERVESCENCE MODE 7 3.2 CHROMATHERAPY OPTION 7 3.3 KEYPAD ICONS 8 3.4 OPERATING THE DIAL CONTROL 9 3.5 OPERATING THE REMOTE CONTROL 10 3.5.1 FUNCTIONS 10 3.5.2 PROGRAMMING 10 3.5 A
Summary of the content on the page No. 3
1.0 INTRODUCTION. RECOMMENDED WATER TEMPERATURE MAXIMUM 40 °C. 1.1 PRODUCT INFORMATION Water capacity Water depth Capacity Working (min.) 250 mm 180 litres Overflow depth 545 mm 420 litres (at waste) Pump Volts Hz Amps 240 50 7.2 1.2 WHIRLPOOL IDENTIFICTION At the time of publication, the Kohler Purist Whirlpool models are: SHAPE SYSTEM SPECIFICATION LEVEL OVAL PURIST 1110-0 OVAL PURIST RELAX 1110-CT-0 1.3 SPECIFICATIONS Access Panel Part No V089160-Issue B Apr 05 Page 3 Kohler Co.
Summary of the content on the page No. 4
2.0 INSTALLATION. 2.1 PRODUCT INSPECTION Your whirlpool has been manufactured to the highest possible standards and has been factory tested. Carefully unpack the product and inspect for any transit damage. NOTE: Warranty does not cover damage caused in transit or by mishandling. When removing the whirlpool from protective packaging, DO NOT LIFT BY THE PIPE WORK. Carefully protect the acrylic surface of the whirlpool during installation using a soft drop cloth. 2.2 ACCESS PANEL Plan fo
Summary of the content on the page No. 5
2.0 INSTALLATION. Cond... 2.3 Spa box ledge Silicone sealant WHIRLPOOL INSTALLATION upstand Finished deck (eg. tiles) IMPORTANT: Whirlpool height may vary, do not build support Waterproof membrane box until product height can be measured Water resistant wall The Purist whirlpool has been designed for material drop-in installation. Timber framing or brick Floor should be flat, level and free of any wall bumps and protrusions. Build stud framing as shown in diagrams, Min 80 mm ensuring tha
Summary of the content on the page No. 6
2.0 INSTALLATION. Cond... 2.5 PDL 596/56RCD-30 ELECTRICAL CONNECTIONS PDL 651 VWP or PDL 691/15 The Purist whirlpool, as a class 1 appliance, may be permanently connected to fixed wiring or connected using the 10A supply plug provided. This should be a separate line, direct from the switch board and should be protected by a residual current device (RCD) with a rated trip current not exceeding 30 mA/30 millisecond and a minimum current rating of 10 Amps. If the supply cord is damaged, it
Summary of the content on the page No. 7
3.0 OPERATION. 3.1 Colour Mood White Pure, clarifying EFFERVESCENCE MODE Violet Inspiring, Creative As water flows through the pump, air is in- Indigo Blue Serene, peaceful troduced into the pump and produces small Aqua Blue Calming champagne like bubbles at the jets. This ef- Green Harmonious, Balancing fervescence is intended to be a relaxing and Yellow Hopeful, illuminating soothing experience. Orange Joyful, spontaneous Red Courageous, energising 3.2 CHROMATHERAPY OPTION (IF FITTED) NOTE
Summary of the content on the page No. 8
3.0 OPERATION. Cond... 3.3 KEYPAD ICONS ICON FUNCTION ACTION STATUS Turn the power on at the The central bargraph will start flashing green wall after 10 seconds. Power Press button All icons on the User Inter face will light up ON/OFF blue ready for use. Effervescence Select icon with the dial Icon flashing blue. ring. Mode Press OK button. Pump running. Pump icon flashing green. Heater on. Heater Icon green. Heater Select icon with the dial Pump on. Pump icon green. ring. Heater icon flashing
Summary of the content on the page No. 9
3.0 OPERATION. Cond... 3.4 OPERATING THE DIAL CONTROL DIAL CONTROL OPERATION. IMPORTANT: Pump will not run if water is not present. Do not operate the whirlpool without water. The Purist whirlpool features a state of the art electronic controller. The system is controlled by a dial control that allows you to select many different functions. The illustration to the below shows the dial control found on the Purist Relax controller. NOTE: Function availability will vary depending on model.
Summary of the content on the page No. 10
3.0 OPERATION. Cond... Power 3.5 OPERATING THE REMOTE CONTROL (OPTIONAL). OK 3.5.1. FUNCTIONS UP Button The remote control can be used to control all Mode the whirlpool functions. DOWN Button The whirlpool can be turned on and off using the power button on the remote control. The M (mode) key is used to scroll through the available functions. Remote The icons on the dial control indicate the functions as detailed on previous page. Pressing O.K. or arrow up key on the remote contro
Summary of the content on the page No. 11
3.0 OPERATION. Cond... bottom LED, on Dial Control central indicator bar, will begin flashing. 4. While the LED is flashing, press the OK button on the Dial Control. A light sequence will illuminate up and down the indicator bar. 5. While the indicator bar light sequence is active, press any button on the remote control. The program will download and the Dial Control will darken. The Dial Control will now respond only to this remote control. 3.6 AUTOMATED FUNCTIONS AUTO TIMER The auto safe
Summary of the content on the page No. 12
3.0 OPERATION. Cond... 3.8 OPERATING THE WHIRLPOOL Power ON / OFF Fill the whirlpool to the recommended level. Turn the power on at the wall. The Dial Control will come to life after 10 seconds displaying a flashing central bargraph. When the flashing central bargraph has finished cycling, press the Power button on the User interface. The icons will all light blue ready for use. A blue icon indicates the function ready for use. A green icon indicates the function is OK Button operating. (act
Summary of the content on the page No. 13
Part No V089160-Issue B Apr 05 Page 13 Kohler Co.
Summary of the content on the page No. 14
Kohler Co. Page 14 Part No V089160-Issue B Apr 05
Summary of the content on the page No. 15
Part No V089160-Issue B Apr 05 Page 15 Kohler Co.
Summary of the content on the page No. 16
CONTACT AND WARRANTY INFORMATION For warranty information, please visit our website Australia www.au.kohler.com New Zealand www.kohler.co.nz CALL US FOR HELP NEW ZEALAND AUSTRALIA KOHLER NZ LTD KOHLER CO. Free Ph: 1 300 362 284 Free Ph: 0800 564 537 (0800 KOHLER) Free Fax: 1 300 652 284 Free Fax: 0800 664 488 www.au.kohler.com www.kohler.co.nz Kohler Co. Page 16 Part No V089160-Issue B Apr 05
