Summary of the content on the page No. 1
Installation Instructions / Warranty
Axor Citterio M
34010XX1
34016XX1
Axor Citterio M
34017XX1
34210XX1
Axor Citterio M
34120XX1
34127XX1
Summary of the content on the page No. 2
Axor Citterio M Lav Mixer 34010XX1 Small Lav Mixer 34016XX1 Lav Mixer less Drain 34017XX1 Tall Lav Mixer 34120XX1 Tall Lav Mixer less Drain 34127XX1 Bidet Mixer 34210XX1 34010XX1 34017XX1 34016XX1 34210XX1 2
Summary of the content on the page No. 3
34120XX1 34127XX1 Technical Information Installation Considerations Recommended water pressure 14.7 - 72.5 psi • For best results, Hansgrohe recom- Max. water pressure 145 psi mends that this unit be installed by Recommended hot water temp. 120� - 140� F* a licensed, professional plumber. Max. hot water temp 165�F* • Please read over these instructions Hole size in mounting surface 1 3/8" thoroughly before beginning instal- Max. mounting surface depth 1 5/8" lation. Make sure that you have
Summary of the content on the page No. 4
Installation Install the drain pull rod*. *Drain and pull rod not included with models 34017XX1 or 34027XX1. Position the faucet and sealing gasket on the mounting surface. Install the fiber washer, friction washer, and mounting nut. Tighten the mounting nut by hand. Tighten the tensioning screws. 4
Summary of the content on the page No. 5
Connect the hot and cold supply hoses to the stops with 3/8" compression fittings (not included). Use two wrenches, as shown, to prevent the hoses from twisting. Set the high temperature limit stop, if desired. Install the pop-up drain. Set the High Temperature Limit Stop (optional) Use a 3 mm Allen wrench to push the screw cover 3 mm through the handle. 2 x Use the Allen wrench to loosen the handle screw 2 complete revolutions. Remove the handle. Retrieve the screw cover. Remove the fl
Summary of the content on the page No. 6
Note: the temperatures given in the diagram assume ° a water heater temperature of 140 F, a cold water ° temperature of 50 F and a water pressure of 45 PSI. Replace the flange. Replace the handle. Tighten the handle screw. Replace the screw cover. 6
Summary of the content on the page No. 7
Install the pop-up drain* Remove the plunger assembly. Unscrew the drain outlet flange from the tee. plunger Unscrew the tailpiece from the tee. Wrap the threads with two layers of Teflon tape and height adjuster replace. Install the white, flexible sealing gasket to the flange. Place it in the sink outlet. flange From under the sink, install the black mack gas- ket, white friction ring and retainer nut to the flange. Do not tighten the nut against the bottom of the sink at this time.
Summary of the content on the page No. 8
User Instructions Turn the water on by pushing the handle up. Turn it off by pushing the handle down. Pivot the handle to the left to make the water warmer, to the right to make it cooler. If the flow of water diminishes, use the service key (included) to remove the aerator. 8
Summary of the content on the page No. 9
Flush the aerator with clear water, then replace it on the faucet. Troubleshooting Problem Possible Cause Solution Insufficient water - Aerator clogged - Clean aerator, replace if neces- sary Mixer stiff - Cartridge defective - Replace cartridge Mixer dripping - Cartridge defective - Replace cartridge Water leaks below handle - Cartridge defective - Replace cartridge - O-ring/rings defective - Replace O-ring/rings Water leaks at the connection - Connection hose defective - Replace connection h
Summary of the content on the page No. 10
Replacement Parts 1.1 1 handle 3403XX0 1.1 screw cover 6762000 1 2 flange 8863XX0 3 nut 8864000 2 4 cartridge 7685000 5 seal 8865000 6 adapter for cartridge 8866000 3 7 aerator 8 26000 8 pull rod 6657XX0 supply hose 470mm 6321001 supply hose 00mm 6316001 10 aerator service key 887000 4 11 fixing set 1361000 12 ball joint 2036XX0 13 spray former 4005XX0 5 XX = colors 23x2 6 00 = chrome 82 = brushed nickel 10 8 7 11 13 12 10
Summary of the content on the page No. 11
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning. Cleaning Materials for Faucets and Showers Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points when cleaning faucet
Summary of the content on the page No. 12
the product for use primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper i
