Summary of the content on the page No. 1
TM
CONCERTO
ALL-CHINA GRAVITY DISCHARGE TOILET
INSTALLATION AND OPERATION
INSTRUCTIONS
Model 3210 Toilet
for Recreation Vehicles
! WARNING
This manual must be read and under-
stood before installation, adjustment,
service, or maintenance is performed.
Modification of this product can
result in property damage.
Dometic Corporation
13128 State Rt. 226, P.O. Box 38
Big Prairie, OH 44611-0038 USA
330-496-3211
1-800-321-9886 • Fax: 330-496-3097
® Registered; ™ Trademark of Dometic Corporation
© Dome
Summary of the content on the page No. 2
TABLE OF CONTENTS Toilet Model Identification ...................................... 2 Flush Mechanism Components ............................. 9 Toilet Dimensions .................................................. 3 Troubleshooting ................................................... 10 Installation Instructions.....................................3 - 6 Parts List ............................................................ 11 Toilet Operation ....................................................
Summary of the content on the page No. 3
TM CONCERTO TOILET DIMENSIONS MODEL 3210 Dimensions may vary ±3/8-inch (13mm). INSTALLATION INSTRUCTIONS System Requirements: • 2 GPM (10.6 lpm) or larger water pump. • 1/2-inch (12.7 mm) water line terminating in 1/2-inch MPT fitting (to connect to toilet water supply hose). • 4-bolt floor (closet) flange. SeaLand flanges available include 3-inch spigot, socket, MPT, or 45-degree swivel socket. • 12 VDC through 2-amp fuse or circuit breaker. Use 14-gauge stranded copper wire. STEP 1: Carefully
Summary of the content on the page No. 4
STEP 5a: For through-the-floor water line and electrical wires, mark another centerline 6 inches (152 mm) from the Below-Floor Installation back wall (fig. 4). Fig. 4 STEP 5b: For through-the-wall water line and electrical Above-Floor Installation wires, mark a centerline 8 inches (203 mm) up from the floor centerline (fig. 5). Fig. 5 STEP 7: Insert floor flange into larger hole and secure to the floor with #12x3/4-inch long flat head wood or sheet STEP 6: Make a 4-3/4 inch (121 mm) diameter hol
Summary of the content on the page No. 5
STEP 9: WITH THE ELECTRICAL POWER OFF, route STEP 13: Temporarily set the toilet in place on the floor #14 gauge stranded copper wire from 12 VDC ground and flange (fig. 14). positive 12 VDC from the fuse panel through a 2-amp fuse or circuit breaker. Leave at least 12 inches (305 mm) of wire for connecting to toilet (fig. 9). Fig. 9 Fig. 14 STEP 14: Mark the holes for the two toilet mounting bolts STEP 10: Connect the holding tank to the bottom of the (fig. 15). discharge flange. STEP 11: Slid
Summary of the content on the page No. 6
STEP 17: Connect the positive (+) 12 VDC lead to the red wire and the negative (-) lead to the black wire (fig. 18). Fig. 18 Fig. 19 Fig. 20 STEP 18: REMOVE RED CAP FROM MIDDLE OF FLANGE ADAPTER BEFORE FINAL TOILET INSTALLATION. IMPORTANT – DO NOT ATTEMPT TO SLIDE THE TOILET OVER THE FLANGE ADAPTER. THE TOILET MUST BE SET DOWN OVER THE ADAPTER TO PREVENT POSSIBLE DAMAGE. Fig. 21 STEP 19: Set the toilet in place (fig. 19) and secure to floor STEP 21: Turn on electrical power and water to toilet
Summary of the content on the page No. 7
PROPER CLEANING AND MAINTENANCE The Concerto toilet should be cleaned regularly for maximum sanitation and operational efficiency. You can clean it just as you would a household toilet. Do not use caustic chemicals, such as drain-opening types, as they will damage the seals. BOWL CLEANING: For stubborn stains, use SeaLand Bowl and Seal Cleaner (fig. A). It’s manufactured especially for use with SeaLand ceramic toilets. In certain locations where water is hard, a build-up of lime may dull the toi
Summary of the content on the page No. 8
DEODORANTS AND SPECIAL TISSUE Your Concerto toilet requires the regular addition of a deodorant product to reduce malodors and to help break down holding tank contents. Several factors should be considered in selecting a deodorant product. Liquid or Dry: Liquid products obviously work more quickly by readily going into solution. Granulated powder formu- lations, on the other hand, have the advantage of requiring less storage space and are less likely to leak if the package is inadvertently da
Summary of the content on the page No. 9
FLUSH MECHANISM COMPONENTS 3. Lift china toilet 1. To access base assembly components, straight up from base remove decorative screw and set it down just in caps and unscrew two front of floor flange. Turn off water to toilet bolts that hold china and disconnect toilet to floor. flexible water line. Disconnect power 2. Remove access wires if necessary. cover from top of china and set it aside. BASE ASSEMBLY COMPONENTS Water Valve (under ceramic toilet) Vacuum Switch Breaker Flush Handle Bracket
Summary of the content on the page No. 10
TROUBLESHOOTING Important: Always turn off electrical power and water to the toilet for disassembly. Problem Possible Cause Service Instructions 1. Toilet emits odor (flush ball a. Odor emitting from base of toilet. a. Use SeaLand brand deodorants. open). b. Plugged holding tank vent line. b. Clear obstructions from vent line. 2. Water will not stay in bowl. a. Improper seal between flush ball a. Clean underside of flush ball seal and seal due to dirt or debris on (see cleaning method on page 7
Summary of the content on the page No. 11
PARTS LIST Description Item Part No. 1 385311001 Access Cover, White 385311002 Access Cover, Bone 2 385311003 Flush Switch Assembly 3 385311004 Flush Handle Shaft Kit 4 385311005 Seat and Lid, White 385311006 Seat and Lid, Bone 5 385311007 China Bowl, White (incl. item 1 and locking material) 385311008 China Bowl, Bone (incl. item 2 and locking material) 6 385311009 Bowl Seal Kit 7 600343534 Ring, Base Insert 8 385311010 Shaft, Flush Ball Kit 9 385311011 J-Bolts (incl. nuts and washers) 10 38531
Summary of the content on the page No. 12
ORDERING PARTS Dometic is ready to assist you in the event service is required. Before calling, please have the following information available. Your cooperation in having this information ready is appreciated and allows us to better meet your needs. 1. Toilet Model Number 2. Serial Number 3. Part Number, Description and Quantity (see Parts List) CUSTOMER SERVICE There is a strong, worldwide network to assist in servicing and maintaining your sanitation system. For the Autho- rized Service Cen
