Summary of the content on the page No. 1
®
PowerScan 7000
Linear Imager
Product Reference Guide
Summary of the content on the page No. 2
PSC Inc 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documenta- tion or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of PSC Inc. or its wholly owned subsidiaries ("PSC"). Owners of PSC products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the
Summary of the content on the page No. 3
Table of Contents About This Manual ............................................................................ 1-1 Manual Conventions .................................................................... 1-2 Connecting the Scanner ..................................................................... 1-2 Programming .............................................................................1-4 Resetting the Standard Product Defaults .............................................. 1-4 Double Rea
Summary of the content on the page No. 4
Wand Idle State ..................................................................3-34 Signal Speed.......................................................................3-36 Transmit Leading Noise ........................................................3-37 Symbology Conversion .........................................................3-38 Keyboard Wedge/USB Keyboard ..................................................3-40 Data Editing Overview .....................................................
Summary of the content on the page No. 5
Code 39 ........................................................................................ 5-30 Disable/Enable Code 39 ............................................................. 5-30 Check Character Calculation ....................................................... 5-30 Check Character Transmit .......................................................... 5-30 Start/Stop Characters ............................................................... 5-30 Code 39 Full ASCII ....................
Summary of the content on the page No. 6
Code 93 Length 1, Length 2 Programming Instructions ..................5-69 Code 93 Stitching ......................................................................5-70 Minimum Reads ........................................................................5-71 MSI/Plessey ...................................................................................5-72 Disable/Enable MSI/Plessey ........................................................5-72 Check Digit Verification ............................
Summary of the content on the page No. 7
Chapter 1 Getting Started ® The PowerScan 7000 Linear Imager marks a new performance level for handheld scanners. It delivers aggressive read rates and depths of field on 1D and stacked codes. This aggressiveness applies even in challenging reading environments where low lighting conditions and poor quality might make it difficult to read bar codes. You can rest assured your investment will continue to supply years of use by reading any bar codes you require, now or in the future. Desi
Summary of the content on the page No. 8
Getting Started Manual Conventions The symbols listed below are used in this manual to notify the reader of key issues or procedures that must be observed when using the scanner: Notes contain information necessary for prop- erly diagnosing, repairing and operating the scanner. NOTE The CAUTION symbol advises you of actions that could damage equipment or property. CAUTION Connecting the Scanner Use the appropriate instructions below to connect the scanner to the ter- minal, PC or other host de
Summary of the content on the page No. 9
K e W y e b d o a g r d e Connecting the Scanner Figure 1. RS-232 Serial Connection Cable Connector Retainer Boss Captive Screws USB Connection — Connect the scanner to a USB port on the termi- nal/PC using the correct USB cable for the interface type you ordered. Reference Figure 2. Figure 2. USB Connection or... or... or... Product Reference Guide 1-3 I U W B a S n M B d
Summary of the content on the page No. 10
Getting Started Wand Emulation Connection — Connect the scanner to the appro- priated port on the terminal/PC using the correct cable for the interface type you ordered. Reference Figure 2. IBM Connection — Connect the scanner to the IBM port on the ter- minal/PC using the correct IBM cable. Reference Figure 2. Keyboard Wedge Connection — The Keyboard Wedge cable has a ‘Y’ connection from the scanner. Connect the female to the male end from the keyboard and the remaining end at the keyboard p
Summary of the content on the page No. 11
Chapter 2 General Features Double Read Timeout The Double Read Timeout feature sets a time limit that determines how much time must pass before reading the same label again (e.g. two identical items in succes- sion). START DURATION BARCODE 0.1 Second 0.2 Second 0.3 Second 0.4 Second Product Reference Guide 2-1
Summary of the content on the page No. 12
General Features Double Read Timeout — continued START DURATION BARCODE 0.5 Second 0.6 Second 0.7 Second ³0 0 4 D 4 6 0.8 Second 0.9 Second 1 Second END ® 2-2 PowerScan 7000 Linear Imager
Summary of the content on the page No. 13
Powerdown Timeout Powerdown Timeout The Powerdown Timeout feature sets the time for automatically switching the unit off when the scanner is not in use. START DURATION BARCODE Disable 5 Seconds 15 Seconds 30 Seconds 1 Minute 2 Minutes Product Reference Guide 2-3
Summary of the content on the page No. 14
General Features Powerdown Timeout — continued START DURATION BARCODE 3 Minutes 4 Minutes END ® 2-4 PowerScan 7000 Linear Imager
Summary of the content on the page No. 15
LED and Beeper Indicators LED and Beeper Indicators Power On Alert Disables or enables the indication (from the Beeper) that the scanner is receiving power. START STATE BARCODE Disable Enable END Product Reference Guide 2-5
Summary of the content on the page No. 16
General Features Good Read: When to Indicate This feature specifies when the scanner will provide indication (beep and/or flash its green LED) upon successfully reading a bar code. Choices are: � Good Read = Indicate after decode � Good Read = Indicate after transmit � Good Read = Indicate after CTS goes inactive, then active This option, which uses CTS, is only valid for RS-232 interfaces. NOTE START INDICATE BARCODE After decode After transmit After CTS goes inactive, then active END ® 2-6
Summary of the content on the page No. 17
LED and Beeper Indicators Good Read Beep Control This feature enables/disables the scanner’s ability to beep upon a success- ful decode of a bar code. START STATE BARCODE Disable Enable END Product Reference Guide 2-7
Summary of the content on the page No. 18
General Features Good Read Beep Frequency Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/ tone.) START FREQUENCY BARCODE Low Medium High END ® 2-8 PowerScan 7000 Linear Imager
Summary of the content on the page No. 19
LED and Beeper Indicators Good Read Beep Length Specifies the duration of a good read beep. START LENGTH BARCODE 60msec 80msec 100msec 120msec 140msec 160msec Product Reference Guide 2-9
Summary of the content on the page No. 20
General Features Good Read Beep Length — continued START LENGTH BARCODE 180msec 200msec END ® 2-10 PowerScan 7000 Linear Imager
