American Standard Reliant 3 7385.00X user manual

Summary of the content on the page No. 1

0



1



2


3


4



5



6


7





Installation
Instructions
7385.00X
Reliant 3
Single Control Centerset Lavatory Faucet with
SpeedConnect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Certified to comply with ANSI A112.18.1
Speed Connect Drain*
M968889 Rev. 1.2
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first ti

Summary of the content on the page No. 2

0 1 2 3 4 5 6 7 POP-UP DRAIN 2 Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN DRAIN POP-UP (3). 3 BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 4 REMOVE FLANGE 3 Fig. A. Fig. B. 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down agains

Summary of the content on the page No. 3

0 1 2 3 4 5 6 7 ATTACH CABLE CONNECTOR 7 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. CHECK OPERATION OF POP-UP 8 1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to t

Summary of the content on the page No. 4

0 1 2 3 4 5 6 7 TEST INSTALLED FITTING 10 ON 1 OFF With HANDLE (1) in OFF position, turn on WATER COLD SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). HOT Operate HANDLE (1) to flush water lines thoroughly. 4 Replace AERATOR (3). 3 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in Sink. If DRAIN STOPPER (5) does not seal properly,

Summary of the content on the page No. 5

0 1 2 3 4 5 6 7 SpeedConnect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain:

Summary of the content on the page No. 6

0 1 2 3 4 5 6 7 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into LOGO the Drain so that the Plastic Loop is facing toward the rear of the S