American Standard Hampton 7881.712 user manual

Summary of the content on the page No. 1

Installation
Instructions
7871.702
7871.712
Spread Lavatory Faucet with the
7871.722
Speed Connect™ Drain
7871.732
7881.702
Congratulations on purchasing your American Standard
7881.712
faucet with Speed Connect drain, a feature found only on
7881.722
American Standard faucets.
7881.732
Certified to comply with ANSI A112.18.1

Speed Connect Drain*
US60404 Rev.1.2
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*You

Summary of the content on the page No. 2

POP-UP DRAIN 2 Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN DRAIN POP-UP (3). 3 BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 4 REMOVE FLANGE Fig. A. Fig. B. 3 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. 4 2 3 INSTALL DRAIN FROM TIGHTEN LOCKNUT REAR

Summary of the content on the page No. 3

ATTACH CABLE CONNECTOR 7 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. CHECK OPERATION OF POP-UP 8 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and 1 closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 2 MAKE WATER SUP

Summary of the content on the page No. 4

INSTALL HANDLES (Lever) INSTALL HANDLES (Cross) 4 10 4 4 Turn VALVE into OFF position. 3 Turn VALVE into OFF position. 6 3 Push ADAPTER (1) into HANDLE Push ADAPTER (1) into HANDLE BASE (2) in a way that the male 7 BASE (2) in a way that the male square on the ADAPTER (1) fits 6 square on the ADAPTER (1) fits in the female square of the 3 in the female square of the HANDLE BASE (2). HANDLE BASE (2). 2 Push HANDLE BASE (2) and WASHER 2 (PORCELIAN Push HANDLE BASE (2) and ADAPTER (1) onto VALVE STEM

Summary of the content on the page No. 5

Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. C

Summary of the content on the page No. 6

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice Fig. G. that the Loop is on one side of the Stopper. Fig. G. LOGO To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper s