Summary of the content on the page No. 1
OPERATOR’S MANUAL
18 VOLT 1/4 in. IMPACT DRIVER
R84230
Your impact driver has been engineered and manufactured to our high standards for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
Summary of the content on the page No. 2
TABLE OF CONTENTS n Introduction .....................................................................................................................................................................2 n General Safety Rules ................................................................................................................................................... 3-4 n Specific Safety Rules......................................................................................................
Summary of the content on the page No. 3
GENERAL SAFETY RULES n Do not overreach. Keep proper footing and balance WARNING! at all times. Proper footing and balance enable better control of the tool in unexpected situations. READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may n Use safety equipment. Always wear eye protection. result in electric shock, fire and/or serious personal Dust mask, non-skid safety shoes, hard hat, or hearing injury. protection must be used for appropriate condition
Summary of the content on the page No. 4
GENERAL SAFETY RULES n When servicing a tool, use only identical replacement SERVICE parts. Follow instructions in the Maintenance section n Tool service must be performed only by qualified of this manual. Use of unauthorized parts or failure to repair personnel. Service or maintenance performed by follow Maintenance Instructions may create a risk of unqualified personnel may result in a risk of injury. shock or injury. SPECIFIC SAFETY RULES n Batteries vent hydrogen gas and can explode in t
Summary of the content on the page No. 5
SAFETY RULES FOR CHARGER tain chemicals that can damage, weaken, or destroy WARNING! plastic. READ AND UNDERSTAND ALL INSTRUCTIONS. n An extension cord should not be used unless Failure to follow all instructions listed below, may absolutely necessary. Use of improper extension result in electric shock, fire and/or serious personal cord could result in a risk of fire and electric shock. If injury. extension cord must be used, make sure: a. That pins on plug of extension cord are the
Summary of the content on the page No. 6
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current n Rotational speed, at no load No Load Speed o Class II Construction Doub
Summary of the content on the page No. 7
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation, which, if not avoided, will DANGER: result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could WARNING: result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, may CAUTION: result in minor or moderate in
Summary of the content on the page No. 8
FEATURES PRODUCT SPECIFICATIONS Blows Per Minute ...........................................0-3,050 BPM Coupler.........................................................1/4 in. Keyless Torque............................................... Maximum 1,450 in.lb. Motor..................................................................18 Volt DC Charger Input ................................... 120 V, 60 Hz, AC only Switch..........................................................Variable Speed Charge R
Summary of the content on the page No. 9
FEATURES KNOW YOUR IMPACT DRIVER DIRECTION OF ROTATION SELECTOR See Figure 1. (FORWARD/REVERSE/CENTER LOCK) Before attempting to use this product, familiarize yourself Your impact driver has a direction of rotation (forward/ with all operating features and safety rules. reverse/center lock) selector located above the switch trigger for changing the direction of bit rotation. Setting the switch BIT STORAGE trigger in the OFF (center lock) position helps reduce the Bits provided with the impac
Summary of the content on the page No. 10
OPERATION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or access
Summary of the content on the page No. 11
OPERATION LED FUNCTION OF CHARGER See Figure 3. LED BATTERY RED GREEN ACTION INDICATOR PACK LED LED Power Without battery pack ON OFF Ready to charge battery pack Evaluate Hot battery pack Flashing OFF When battery pack reaches cooled temperature, charger begins fast charge mode Evaluate Cold battery pack Flashing OFF When battery pack reaches warmed temperature, charger begins fast charge mode Evaluate Deeply discharged Flashing OFF Charger pre-charges battery until normal voltage is reach
Summary of the content on the page No. 12
OPERATION TO INSTALL BATTERY PACK See Figure 4. n Place the battery pack in the impact driver, aligning raised rib on battery pack with groove in the driver’s battery port. n Make sure the latches on each side of the battery pack snap into place and the battery pack is secured to the impact driver before beginning operation. RAISED RIBS CAUTION: When placing battery pack in the tool, be sure LATCHES raised rib on battery pack aligns with the bottom of the impact driver and latches into pla
Summary of the content on the page No. 13
OPERATION DIRECTION OF ROTATION SELECTOR DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE/CENTER LOCK) See Figure 6. The direction of bit rotation is reversible and is controlled by REVERSE a selector located above the switch trigger. With the impact driver held in normal operating position, the direction of rota- tion selector should be positioned to the left of the switch trigger for driving. The driving direction is reversed when the selector is to the right of the switch trigger. Settin
Summary of the content on the page No. 14
OPERATION WARNING: Do not drive a screw where there is likely to be hidden wiring behind the surface. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. If you must drive a screw where hidden wire may be present, always hold tool by insulated gripping surfaces (handle) when performing the operation to prevent a shock to the operator, as seen in figure 8. CAUTION: The impact driver is not designed to be used as a drill. DRIVING OR REMOVING
Summary of the content on the page No. 15
MAINTENANCE GENERAL MAINTENANCE WARNING: Avoid using solvents when cleaning plastic parts. Most When servicing use only identical RIDGID plastics are susceptible to damage from various types of replacement parts. Use of any other parts may commercial solvents and may be damaged by their use. Use create a hazard or cause product damage. clean cloths to remove dirt, dust, oil, grease, etc. WARNING: WARNING: Do not at any time let brake fluids, gasoline, Always wear safety goggles or safet
Summary of the content on the page No. 16
NOTES 16
Summary of the content on the page No. 17
WARRANTY ® RIDGID HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY Proof of purchase must be presented when requesting war- WHAT IS NOT COVERED ranty service. This warranty applies only to the original purchaser at retail ® and may not be transferred. This warranty only covers de- Limited to RIDGID hand held and stationary power tools fects arising under normal usage and does not cover any purchased 2/1/04 and after. This product is manufactured malfunction, failure or d
Summary of the content on the page No. 18
OPERATOR’S MANUAL 18 VOLT 1/4 in. IMPACT DRIVER R84230 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com. The model number of this tool is found on a plate attached to the motor housing. Please record the serial number in the space provided bel
