Summary of the content on the page No. 1
ESPAÑOL: PÁGINA 9
Instruction manual
FRANÇAIS: PAGE 17
Manual de
Instrucciones
1/2” Impact Wrench
Manuel d'instructions
Herramienta
neumática de impacto,
de 1/2"
Clé à chocs de 1/2 po
MODEL PT501
MODELO PT501
MODÈLE PT501
To learn more about Porter-Cable visit
our website at:
http://www.porter-cable.com
IMPORTANT
Para obtener más información sobre
Please make certain that the person who is
Porter-Cable, visite nuestro sitio web en:
to use this equipment carefully reads and
http://www.porter-c
Summary of the content on the page No. 2
SAFETY GUIDELINES - DEFINITIONS This manual contains indicates an imminently hazardous situation which, if not information that is avoided, will result in death or serious injury. important for you to know and indicates a potentially hazardous situation which, if not understand. This information re- avoided, could result in death or serious injury. lates to protecting YOUR SAFE- TY and PREVENTING indicates a potentially hazardous situation which, if not EQUIPMENT PROBLEMS. To avoided,may result
Summary of the content on the page No. 3
HAZARD RISK OF LOSS OF HEARING WHAT COULD HAPPEN HOW TO PREVENT IT Long term exposure to noise produced from the opera- Always wear ANSI S3.19 hearing protection. tion of air tools can lead to permanent hearing loss. HAZARD RISK TO BREATHING INHALATION HAZARD WHAT COULD HAPPEN HOW TO PREVENT IT Abrasive tools, such as grinders, sanders, and cut-off Always wear MSHA/NIOSH approved, properly fitting tools generate dust and abrasive materials which can face mask or respirator when using suc
Summary of the content on the page No. 4
HAZARD RISK OF INJURY (continued) WHAT COULD HAPPEN HOW TO PREVENT IT Improperly maintained tools and accessories can cause Maintain the tool with care. serious injury. Keep a cutting tool sharp and clean. A properly maintained tool, with sharp cutting edges reduces the risk of binding and is easier to control. There is a risk of bursting if the tool is damaged. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operati
Summary of the content on the page No. 5
SPECIFICATIONS Maximum Torque 400 ft./lbs. Blows Per Minute 1000 Free Speed RPM @ 90 PSI 7000 Maximum Working Pressure 90 PSI Air Inlet 1/4” NPT Recommended Hose Size 3/8” I.D. Air Consumption @ 90 PSI 4.2 SCFM ASSEMBLY Accessories Required IMPORTANT: Line pressure or hose inside diameter should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D. and fittings should have 1/4” NPT thread. OPERATION Operation Before each use: Drain
Summary of the content on the page No. 6
Place tool in forward or reverse position. Push button in on “F” side for forward or “R” side for reverse. Push button all the way in on Push button all the way in on the “R” side for Reverse the “F” side for Forward position. position. Depress the trigger to operate tool. Release trigger to stop tool. Always disconnect air supply when changing sockets. When job is complete, turn the air compressor off and store as described in the air compressor operator manual. MAINTENANCE Lubricatio
Summary of the content on the page No. 7
REPAIR PARTS 16 8 9 34 7 30 (2) 26 42 (6) 29 27 48 (2) 22 3 45 17 25 28 21 24 18 47 4 39 Ref No. Part No. Description Qty 3 u O-Ring 1 4 u O-Ring 1 7 s Anvil Collar 1 8 u Anvil 1 9 u Spring 1 16 s O-Ring 1 17 + Trigger 1 18 s Rubber Grip 1 21 + O-Ring 1 22 + Spring Pin 1 24 + O-Ring 1 25 + Valve Body 1 26 + O-Ring 1 27 + Valve Stem 1 28 + Regulator Bushing 1 29 + E-Ring 1 30 + Spring Pin 1 34 u O-Ring 1 39 u Gasket 1 42 u Rotor Blade 6 45 u Spring 1 47 u O-Ring 1 48 + Spring 1 + Only available
Summary of the content on the page No. 8
LIMITED WARRANTY PORTER-CABLE CORPORATION warrants to the original purchaser that all products covered under this warranty are free from defects in material and workmanship. Products covered under this warranty include air compressors, air tools, service parts, pressure washers, and generators, which have the following warranty periods: 3 YEARS - Limited warranty on 2-stage oil-free air compressor pumps that operate at 1725 RPM. 2 YEARS - Limited warranty on oil-lubricated air compressor pumps.
