Summary of the content on the page No. 1
Baby Monitor
Secure 200
User Guide
Summary of the content on the page No. 2
TABLE OF CONTENTS WARNINGS AND SAFETY INFORMATION 1 GETTING STARTED 3 YOUR BABY MONITOR 5 LCD DISPLAY OF BABY MONITOR 8 BASIC OPERATION 9 MENU SETTINGS 14 TROUBLESHOOTING 19 PRODUCT SPECIFICATIONS 20 GUARANTEE 21
Summary of the content on the page No. 3
WARNINGS AND SAFETY INFORMATION 1 Do not place the cord in a high "wear and tear" location. IMPORTANT Never use a frayed or compromised cord. Please read this user guide thoroughly before use. Never use or place your Parent or Baby units in or near Your ORICOM Baby Monitor is designed to be an aid and moisture or water (e.g. near bath or pool). Immersing in should not be used as a substitute for responsible and water can cause electric shock and even death. proper adult supervision of a chi
Summary of the content on the page No. 4
2 WARNINGS AND SAFETY INFORMATION • The Ni-MH batteries supplied with this product may be Battery requirements able to be recycled once they are unable to recharge during normal operation. Always observe your local Each parent unit requires two rechargeable Ni-MH Council /State regulations regarding the disposal of batteries, size AAA 1.2V 800mAh (HR10/44). your packaging materials, exhausted batteries, and old • Do not dispose of the batteries in a fi re, as they can equipment. explode.
Summary of the content on the page No. 5
GETTING STARTED 3 Thank you for choosing this monitor from Oricom. Installation Your Secure 200 Baby Monitor offers the best Digital Technology. For the Parent Unit clip 1. Remove the Belt Clip by lifting the clip at the top and INTERFERENCE sliding it downwards. FREE FREQUENCY 2. Then remove the battery DECT (Digital Enhanced Cordless Telecommunications) is the cover on the back of the most widely used worldwide digital cordless technology, offering Parent Unit by pressing amazingly cle
Summary of the content on the page No. 6
4 GETTING STARTED 5. Press [ ] to turn the Parent Unit on. 4. Press and hold [ ] key to turn on the baby unit. • Before fi rst use, or if it has been out of use for a long • The Baby Unit should be placed about 1 metre time, the Parent Unit will need to be charged for 15-16 to 1.5 metres away from the baby's cot on a flat hours. During this time, the Parent Unit will operate surface. Never place the Baby Unit inside the cot, from the Charger pod when switched on. Note that the bed or plaype
Summary of the content on the page No. 7
YOUR BABY MONITOR 5 Baby unit (Sender) 1 Temperature Sensor 9 Microphone Picks up the temperature in your baby's room. Picks up the sounds from your baby's room. 10 Volume Up/Down Keys 2 Battery Cover Volume −: Reduces the lullaby volume. For non rechargeable batteries (not supplied). 3 Night light key Volume +: Increases the lullaby volume. Press to turn On the night light. Press again to turn Off the light. 1 2 4 Power On/Off Key Press to turn ON the Baby unit. Press and hold to turn O
Summary of the content on the page No. 8
6 YOUR BABY MONITOR Left view of baby unit Parent unit (Receiver) 11 DC 6V input 12 Battery Cover Connecting to Power Adaptor. Rechargeable batteries. 13 Belt Clip 14 Volume Up/Down Keys Adjust the volume at which you hear the sounds in your Baby's room, and scroll through the menu during setting. 15 Power On/Off Key Press to turn the parent unit ON. Press and hold to turn OFF. 11 13 14 15 12
Summary of the content on the page No. 9
YOUR BABY MONITOR 7 16 Menu key, [OK] key 19 Noise level indicators Press to adjust the features of your Baby Monitor. 20 Torch key Press [ ] key to enter the menu options, use [ / ] Press and hold to emit a soft beam of light from the top keys to scroll through the menu choices and [OK] key to of the Parent Unit. select. Press [ ] key to exit. 21 Talk key 17 Link Light Press and hold to talk to your baby or partner in the Green light ON indicates "Linked" to Baby Unit. Flashing baby's ro
Summary of the content on the page No. 10
8 LCD DISPLAY OF BABY MONITOR Baby Unit Parent Unit 1. Battery level indicator 1. Sensitivity indicator 2. Numbers/Characters indicator 2. Night light indicator 3. Temperature indicator 3. Battery level indicator 4. Lullaby on/off indicator 4. Numbers/Characters indicator 5. Temperature indicator 6. Feed time Alarm indicator 7. Lullaby on/off indicator 5 1 1 3 4 2 2 6 3 7 4
Summary of the content on the page No. 11
BASIC OPERATION 9 Once you have set up your Baby Monitor, you will be able and 3 red). The more audio is picked up, the more to hear the sounds in your baby's room through the Parent lights will be lit. When no audio is picked up, all 8 Unit. And also see the green and red sensor lights around lights will be off. the top of the Parent Unit rise and fall with the sound levels. • If the volume of the Parent Unit is turned off, an alert Note: will sound when the audio reaches the second red If
Summary of the content on the page No. 12
10 BASIC OPERATION Baby alert! Night light You can set your Parent Unit to give an extra warning The Baby Unit has a night light which emits a soft starry "beep" when the noise levels in your baby's room is glow, providing comfort and reassurance for your baby and high and the red lights on the sound sensor are lit. This allowing you to see them in a darkened room. is particularly useful if the volume of your Parent Unit is turned down and you are just using the sensor lights to On the baby
Summary of the content on the page No. 13
BASIC OPERATION 11 2. Press [ ] key to scroll to the different lullabies, or to Temperature select [Play all?]. It is very important for your baby's health to ensure that 3. Press [ ] key again to start or stop the lullaby. they are kept at a safe temperature. This includes the On the Parent Unit room temperature, baby's temperature, baby clothing and bedding (contact your local health authority to ensure you 1. Press [ ] key, then use [ / ] keys to scroll to are aware of the current re
Summary of the content on the page No. 14
12 BASIC OPERATION will be shown on both units LCD display. When the units are Talk to your Baby linked, the green Link light will be steadily lit. You can speak to your baby from the Parent Unit, perhaps to reassure them that you are on your way. Torch Press and hold [ ] key and speak into the front of the The Parent Unit has a useful Torch feature. Press and hold Parent Unit. the button on the parent unit, a soft beam of light is emitted • Please note that you will not be able to hear y
Summary of the content on the page No. 15
BASIC OPERATION 13 Rechargeable batteries in the Parent unit give up to 10 Charging the Battery hours continuous usage. Please note however, that new batteries do not reach full capacity until they have been in The Parent Unit will work for up to 10 hours with fully normal use for several days. charged batteries. If a battery low alert tone is heard and the battery icon on the Parent Unit's display is fl ashing, you Running rechargeable batteries right down at least once a should put the
Summary of the content on the page No. 16
14 MENU SETTINGS Note: All Menu settings operations are only available on the Parent unit. During setting, press [ ] key to exit. Night light Setting Start playing You can turn on or off the night light on the baby unit via Press [ OK ] key, "Play?" is shown, press [ OK ] key to play the parent unit. the lullaby and "Saved" is shown on the display. 1. Press [ ] key on the parent unit and use [ / ] keys To stop lullaby, press [OK] again, "Stop?" is shown and to select "Night Light". The d
Summary of the content on the page No. 17
MENU SETTINGS 15 1. Press [ ] key on the parent unit and use [ / ] keys Set On or Off to select "Sensitivity". The display is shown below: 1. Press [ OK ] key, "On?" or "Off?" is shown on the display, press [ OK ] key to select Sound Alert on or off and "Saved" will be displayed on the parent unit. Adjust Volume 2. In the Sound Alert setting menu, use [ / ] keys to select "Volume" and press [ OK ] key. 2. Press [ OK ] key and then use [ / ] keys to select the 3. Use [ / ] keys to select th
Summary of the content on the page No. 18
16 MENU SETTINGS Press [ ] key on the parent unit and use [ / ] keys to Set degree Centigrade or Fahrenheit select "Temperature". The display is shown below: You can choose whether to view the temperature of your baby's room in degrees Centigrade or degrees Fahrenheit. Your monitor is pre-set to Centigrade, but if you wish to change it, follow the steps below: 1. In the Temperature setting menu, use [ / ] keys to select "Degree F" or "Degree C". 2. Press [ OK ] key to confi rm and "Saved" w
Summary of the content on the page No. 19
MENU SETTINGS 17 baby's feeds are due. You have the choice to either set an Set the time alert just for your baby's next feed time, or for your baby's 2. Press [ OK ] key and "Set time" is shown on the display. next feed time plus subsequent feeds based on the interval Press [ OK ] key. time between them. 3. "Year" is shown on the display. Use [ / ] keys to Firstly you will need to ensure that you have set the date select the correct year. Press [ OK ] key. and time on your Parent Unit's in
Summary of the content on the page No. 20
18 MENU SETTINGS Set the fi rst or next feed time Language Setting 1. Press [OK] key, "Set Time" is shown on the display. The displayed information can be set in different 2. Press [ OK ] key, then follow the procedures in the Set languages. the time of Clock Setting to set the hour and minute. 1. Press [ ] key and use [ / ] keys to scroll to Set the interval for following feeds "Language". The display is shown below: 1. Press [ OK ] key and use [ / ] keys to select "Set Interval". 2. Press
