Summary of the content on the page No. 1
User’s Manual
BCD-1100 Series
Customer Display
Rev. 1.00
http://www.bixolon.com
Summary of the content on the page No. 2
BCD-1100 ■ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING & CAUTION Violating following instructions can cause serious injury or death. Violating following instructions can cause slight wound or damage the appliance. If you observe a strange smoke, odor or noise from Keep the desiccant out of children’s reach. the Display, unplug it before taking following • If not,
Summary of the content on the page No. 3
BCD-1100 ■ Table of Contents 1. Complete Product Configuration................................................................................. 4 2. Unpacking ..................................................................................................................... 5 2-1 BCD-1100DN Type.................................................................................................... 5 2-2 BCD-1100D Type .....................................................................
Summary of the content on the page No. 4
BCD-1100 1. Complete Product Configuration The display types offered include the following : - Desk-Top Type (BCD-1100D) - Desk-Top Fix Type (BCD-1100DN) - Wall Mount Types (BCD-1100W/WN) BCD-1100DN BCD-1100D BCD-1100WN BCD-1100W ※ NOTES ※ NOTES For the table installation, please fix a For the wall-mounting installation, please fix product tightly using screw. a product tightly using screw. - 4 - Rev. 1.00
Summary of the content on the page No. 5
BCD-1100 2. Unpacking 2-1 BCD-1100DN Type Display Set Manual Install CD Screw (M3*10) Tapping 2-2 BCD-1100D Type Display Set Manual Install CD - 5 - Rev. 1.00
Summary of the content on the page No. 6
BCD-1100 2-3 BCD-1100W Type Display Set Manual Install CD Screw (M3*10) Tapping 2-4 BCD-1100WN Type Display Set Manual Install CD Screw (M3*10) Tapping - 6 - Rev. 1.00
Summary of the content on the page No. 7
BCD-1100 3. Connection Type STEP1. Connect the display cable to a computer via a USB port. STEP2. Turning on the computer and the power supply unit leads to the automatic detection of the new hardware connected to the PC via the USB port. STEP3. Install the USB Virtual COM driver. (Refer to 7. USB Virtual COM Driver Installation) STEP4. After driver installation is complete, data can be received. - 7 - Rev. 1.00
Summary of the content on the page No. 8
BCD-1100 4. Size 4-1 Desk Top Type 4-2 Wall Mount Type 4-3 Etc. - 8 - Rev. 1.00
Summary of the content on the page No. 9
BCD-1100 5. Function 5-1 Rotation This product allows display rotation to any position or angle desired by the user. Please adhere to the following instructions during installation to prevent possible product damage and/or malfunction. Following assembly, follow the sequence below to fix the DISPLAY in the desired position. POLE-ADJUST NUT-FIX POLE-MAIN (a) (b) (c) (a) Lower the DISPLAY UNIT in the direction of the arrow. Rotate the NUT-FIX to allow for lowering.
Summary of the content on the page No. 10
BCD-1100 5-2 Angling This product allows display tilting to any angle desired by the user. Please adhere to the following instructions during installation to prevent possible product damage and/or malfunction. TILT ANGLE : The display can be angled left and right from the Center Line in 13° angle intervals for a total of 4 steps, 5 positions. (Angling: 52°max.) Center Line Center Line - 10 - Rev. 1.00
Summary of the content on the page No. 11
BCD-1100 6. Switches 6-1 Display Switch 6-1-1 Feature : A Display Switch is located on the bottom of the display panel. 6-1-2 Function : Turns the power supply on/off. 6-2 DIP switches 6-2-1 Feature : Two DIP switches are located on the back of the display panel. You can remove the DIP switch cover by pushing the hook. 6-2-2 Function: DIP switch settings can be read only when the power is on. Therefore, any changes to the settings when the power is on do not take effect.
Summary of the content on the page No. 12
BCD-1100 6-3 Memory Switches The following settings other than the DIP switch can be changed by software. These settings become effective after the power is turned on or initialization is executed by a command. No. Function Default Content to be set Range to be set Character code table 0-5, 16-19, Msw 10 n=0 Page 0 is selected section 254, 255 International character set Msw 11 n=0 U.S.A is selected 0-13 selection Msw 12 Brightness adjustment n=4 100% 1-4 Selection of the Msw 1
Summary of the content on the page No. 13
BCD-1100 7. USB Virtual COM Installation PC requires software installation when it detects new hardware connected to USB Port. First, connect BDC-1100DU/WU (USB) to PC USB Port and install software and set the conditions as below. 1) Connect BDC-1100DU/WU (USB) to PC USB Port. Message will pop up Found New Hardware. 2) Select Install from a list or specific location (Advanced). 3) Select the location VirtualCOM￦2K&XP by Browse and select Next. - 13 - Rev. 1.00
Summary of the content on the page No. 14
BCD-1100 4) Message pops up again at right bottom of PC Found New Hardware (USB Serial Port) when it completes. 5) Repeat step 1) thru 3) again at Found New Hardware Wizard. It installs twice. 6) Open Device Manager (Start > Control Panel > System > Hardware > Device Manager) - 14 - Rev. 1.00
Summary of the content on the page No. 15
BCD-1100 7) Select USB Serial Port(COM x) and click on the right button of mouse. Then select Properties. COM port is automatically numbered and it varies from PC port occupation conditions. 8) Set Serial communication conditions and select Advanced. Preset Serial conditions are 9600 bps, 8 data bit, none parity, hardware flow control. They must be the same with Master setting and application program Serial setting. - 15 - Rev. 1.00
Summary of the content on the page No. 16
BCD-1100 9) Check in the boxes of Serial Enumerator and Serial printer. Then select OK. Now Virtual COM driver has been installed Successfully. (Windows 98 does not have the boxes of Serial enumerator and Serial printer) - 16 - Rev. 1.00
Summary of the content on the page No. 17
BCD-1100 8. Appendix 8-1 Specifications Item Description Display Method VFD Brightness 800~1000 [cd/㎡] Character Size 5 x 7 [dot] Display Number of Columns 20 character, 2 line Operating Temperature 0~70 ℃ Operating Humidity 20~85 % Reliability VFD 20,000 [hour] 8-2 Certification 1) EMC & Safety Standards • Europe: CE EMC, TUV GS: EN60950-1: 2001 • North America: FCC Part 15 Subpart B • Safety Standards: CB-scheme: IEC60950-1: 2001 WARNING Use of an unprotect
Summary of the content on the page No. 18
BCD-1100 3) WEEE (Waste Electrical and Electric Equipment) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retaile
