Summary of the content on the page No. 1
TS2000
Installation & User Guide
Compatible Equipment
CPA6 OM - Output Module
9040 - Loudspeaker
DC54/58 - Digital Communicators
496529 Issue A 1 of 20 TS2000
Summary of the content on the page No. 2
TS2000 OVERVIEW Introduction and a 40 character display to allow operators to control the system. The system will consist of a CP connected, via the The Intruder Alarm Control System TS2000 is provided for Control Network, to up to 32 NU’s and or REM’s so large domestic and general commercial intruder providing up to 128 circuits and programmable outputs systems conforming to BS 4737 part 1 1986. It is an each of whose functioning and use are extremely versatile system with the following facilit
Summary of the content on the page No. 3
TS2000 Additional Equipments Remote Data Transfer Ward Control Unit (WCU): When fitted the WCU will allow When fitted with a Digimodem type DC3M the system a group of circuits, which are designated a Ward, to be may be programmed from a remote location, and log Set and Unset using Exit and Entry routes separate from data transferred to it, using a dedicated program the system. The WCU is connected to the outputs and installed in a Personal Computer at that location. The circuits of a REM or a NU
Summary of the content on the page No. 4
TS2000 Schematic Block Diagram PSTN Lines* Mains input CONTROL Other Option Outputs 240V 50Hz PANEL Programmable Option Outputs Control Network Cable Detection Programmable NODE OR Circuits Outputs REMOTE KEYPAD C001 - C004 S001 - S004 No 1 Control Network cable 2 Cable: 6 or 8 core 7/0.2mm min. Max length 100m between units NODE OR Programmable Detection Circuits REMOTE KEYPAD Outputs C005 - C008 S005 -S008 No 2 Control Network Cable 4 Output Circuits for WCU Exit/Entry WARD NODE OR Circuits CO
Summary of the content on the page No. 5
TS2000 TS2000 System Options - Schematic P.C. Approved To PSTN DC3(M)* Modem TS2000 CPMAINBOARD OR DC3* CONTROL To PSTN PANEL PSU PIB* SIB* Central Mains Input Station To Epson* Printer 8 Programmable DC 28 PSTN Line outputs Digicom To Serial Printer* Network CPA6.OM Unit* 8Outputs* Cable 8Outputs* CPA6.OM Unit* Other outputs: Wlk Test, Tamp, Aux, Relay, Sw12, Strobe Bell (SAB1) Sounder (ES1) 12V supply Loudspeaker Loudspeaker* Four Circuits Drive LSD1* (Min impedance 8R) NODE UNIT Three Outputs
Summary of the content on the page No. 6
TS2000 Equipment Power Supply The CP is fitted with the system combined Power Supply System Specification and Battery Charger Unit and a battery which will provide Supply Voltage: 240V + or - 10% 30W 50 Hz power during a mains failure. Power arrangements are Battery: 12V 6Ah as follows: Zones: 128 maximum Outputs: 128 remote 8 local maximum 1 Mains input 240V +/- 10% Unit Dimensions: CP L 395 x W 280 x D 100mm 2 Battery 12V 6Ah Sealed Lead Acid rechargeable (boxed) NU/WCU L 145 x W 85 x D
Summary of the content on the page No. 7
TS2000 The REM’s are used to control and programme the Node Unit (NU) system hence they must be positioned at suitable control positions with easy access. The NU comprises a small two part polycarbonate case containing a single pcb on which are terminal blocks. Ward Control Unit (WCU) The unit is connected to the control network and is a control and connecting device for four circuits and four programmable outputs. It also contains a sounder The WCU comprises the same case as the NU and output a
Summary of the content on the page No. 8
TS2000 TS2000 8 of 20 496529 Issue A DOWN DIR +12V OV TAMP C NC STRB DOWN DIR LAT CLK DAT NO WLK TST SW 12 0V +12V + - RELAY - + POWER INPUT Relay contacts are Connect to Control Network For Mimic. Connect to shown in the See Fig 6 CPA6.OM module. de-energised state. . Connect Alarm relay is normally to PIR if energised and is required. For SAB Tamper. de-energised at alarm. Link to 0V if not used 12V supply present when Figure 4. Control Panel Main Board - Connections system is set Fuse F1 on t
Summary of the content on the page No. 9
TS2000 Figure 6. TS2000 Network Connections 496529 Issue A 9 of 20 TS2000 Continue to next unit Connect PSU where When using 8 core cable use required the two spare cores for non MAINS network power supplies Control Node or REM Node or REM Node or REM Panel +12V +12V 0V 0V Up+ Dn + Dn + Up+ Dn + Down + Up+ Dn - Dn - Dn - UP - UP - Down - UP - Dir + Dir + Dir + Dir + Dir- Dir- Dir - Dir- +12V +12V +12V +12V 0V 0V 0V 0v Use for Network Cable 6 or 8 core 7/0.2mm power to NU and Maximum length 100m
Summary of the content on the page No. 10
TS2000 B+ MUTE NOT USED CIRCUIT B I/P B SOUND TO LSD1 FOR SPEAKER DEVICE A+ C+ CIRCUIT A CIRCUIT C I/P A I/P C O/P D D+ OUTPUT D SINK 100mA CIRCUIT D O/P C OUTPUT C SINK 100mA I/P D +DIR OUTPUT A SOURCE O/P A -DIR O/P B OUTPUT B 12V 100mA 0v UP - +12V UP + SPARE 1 DOWN - SPARE 2 DOWN + CONNECTTOCP(FIG4) OR TO PREVIOUS UNIT (DOWN) CONNECT TO CP (FIG 4) CONNECT TO OR PREVIOUS UNIT AND TO NEXT UNIT NEXT UNIT (Up) SPARES ARE NOT CONNECTED INTERNALLY Figure 7 TS2000 Node Unit - Connections OUT D Outp
Summary of the content on the page No. 11
TS2000 W.C.U To nc contacts of ACCESS Access device* To Loudspeaker SPKR Connect other side to 0V ACCESS To nc contacts of To NU/REM Cct C. LAST Last Exit device C+ and I/P C EXIT OUT LX To nc contacts of To NU/REM Cct B. EXIT Exit Terminator* B+ and I/P B OUT TERMINATE To NU/REM o/p C WARD WARD SET To NU/REM Cct A. To NU/REM o/p B CONTROL A+ and I/P A WARD EXIT 0V To NU/REM o/p A SET FAIL 12V power supply input +12V To NU/REM o/p D WARD ALARM * = options Power supply must be sufficient topowert
Summary of the content on the page No. 12
TS2000 Figure 11. TS2000 Circuit and Output Connections TS2000 12 of 20 496529 Issue A Detector No 1 Detector No n (<11) Detector No2 Detector Sw Detector Sw Detector Sw + 4k7 4k7 To Node/REM 4k7 EOL Res I/P 2k2 Tamper Sw Tamper Sw Tamper Sw Detection Circuit Connections For PSU monitor circuits connect monitor lines directly to I/P A or B or C or D and leave the relevant +ve connection open Detector Sw Exit Terminator n.c. (Or n.o.) Contacts E.O.L. Res X+ X+ 2k2 EOL Res To Node/REM 4k7 To Node/
Summary of the content on the page No. 13
TS2000 Key Functions Engineer Reset Control Panel Links 1. Enter your engineer’s code default 1234, you are Link Functions now in Engineer’s Mode LK1 Open: Printer to monitor Network 2. Press0 in quit to unset. activity Closed: Normal; Printer normal and responds to keypad Loading Defaults commands 1. Power down panel battery and mains, close LK2 LK2 Open: Normal; On-site restart at power up 2. Power up panel battery and mains Closed:Factory restart at power 3. Enter 1234 and open LK2 up 4. The
Summary of the content on the page No. 14
TS2000 Define Circuit Text STEP ACTION DISPLAY REMARKS 1 NO* Press < YES > to Press YES to Define Circuit Text from the dictionary. Press DEFINE CIRCUIT TEXT NO to go to to Install DC3 menu. Press 0 to quit 2 YES CCT > 001 000 000 000 Press YES to accept displayed data. Press NO to change it. Enter figures or use arrow keys to enter a new circuit 3 NO CCT 001 > 000 000 000 Text is to be changed. Enter number of the first word of text (see dictionary) then press YES to accept it 4 123 CCT 001>1
Summary of the content on the page No. 15
TS2000 TS2000 Dictionary 001 A 056 CEILING 111 ENTRANCE 002 ABOVE 057 CELL 112 ENTRY 003 ACCESS 058 CELLAR 113 EQUIPMENT 004 ACCOUNTS 059 CENTRAL 114 ESCAPE 005 ADMIN 060 CENTRE 115 EXIT 006 ALARM 061 CHAIR 116 EXPORT 007 ALERT 062 CHANGING 117 EXTERNAL 008 ANNEXE 063 CLASSROOM 009 AREA 064 CLEANERS 118 F 010 ART 065 CLERK 119 FACTORY 011 ASSEMBLY 066 CLERKS 120 FAILURE 012 ASSISTANT 067 COIN 121 FAR 013 AT 068 COLD 122 FEMALE 014 ATTACK 069 COLLECTION 123 FENCE 015 ATTIC 070 COMMUNICATOR 124 FI
Summary of the content on the page No. 16
TS2000 TS2000 Dictionary Cont’d 164 INFRA-RED 217 METER 271 PORCH 165 INSIDE 218 MEZZANINE 272 POST 166 INSTRUCTORS 219 MICROWAVE 273 POWER 167 INTERIOR 220 MIDDLE 274 PRESSURE 168 INTO 221 MILK 275 PRIMARY 169 IRON 222 MINOR 276 PRIME 170 IT 223 MOBILE 277 PRINT 224 MODEL 278 PROCESSING 171 J 225 MONITOR 279 PRODUCTION 172 JANITOR 226 MOULDING 280 PUBLIC 173 JUNIOR 227 MOVEMENT 281 PURCHASING 282 PURPLE 174 K 228 N 175 KEEP 229 NEAR 283 Q 176 KEYPAD 230 NEW 284 QUALITY 177 KITCHEN 231 NEXT 285
Summary of the content on the page No. 17
TS2000 TS2000 Dictionary Cont’d 325 SITE 381 TRAP 431 11 326 SITTING 382 T.V. 432 12 327 SLIDING 383 TWIN 433 13 328 SMOKE 384 TYPE 434 14 329 SOFTWARE 385 TYPING 435 15 330 SOUND 386 TYRE 436 16 331 SOUTH 437 17 332 SPRAY 387 U 438 18 333 SPRING 388 ULTRA-SONIC 439 19 334 SQUARE 389 UNDER 440 2 335 SQUASH 390 UNIT 441 2ND 336 STABLE 391 UP 442 20 337 STAFF 392 UPPER 443 3 338 STAIRS 393 UPSTAIRS 444 3RD 339 STAIRWELL 394 USER 445 4 340 STALLS 395 UTILITY 446 4TH 341 STAND 447 5 342 START 396 V
Summary of the content on the page No. 18
TS2000 (26) Exit Setting: Final Exit setting is in progress Programmable Ouputs (27) Exit Error: An error occurred during the exit procedure and the system cannot set The programmable outputs from the NU and the REM, (28) Lock Alert: The programmed Time Lock period is are referred to as the Node Outputs and are activated in about to start; response to various conditions or events. They are (29) Fire/Viper: Will provide 12V (100mA source) to devices which latch when activated and which programmed
Summary of the content on the page No. 19
TS2000 Menus Listing in Sequence Menu No Menu Passcode Level 1 Start Set Sequence 1, 2, 3, 4, 5, 6 2 Unset Wards 1, 2, 3, 4, 5, 6 User 3 View Circuits 1, 2, 3, 4, 5, 6 4 View Event Log 1, 2, 3 5 Select Walk Test 1, 2, 3, 4, 5 6 Select Bell Test 1, 2, 3, 4, 5 7 Omit/Enable Circuit 1, 2, 3 8 Use Chime Facility 1, 2, 3 9 Use the Printer 1, 2, 3, 10 Alter Clock 1, 2 11 Alter Passcode 1, 3, 4, 5, 6 12 Define Users 2 13 Alter Time Switch 1, 2 14 Alter Time Lock 1, 2 15 Define Circuits 1 Eng’r 16 Defin
Summary of the content on the page No. 20
TS2000 This page intentionally left blank TS2000 20 of 20 496529 Issue A
