Summary of the content on the page No. 1
INSTALLATION/OPERATION
®
ES30PC/ES31PC Esprit
with Pressurized IOC
U.S. Patent D-472.260
C311M-N (6/06)
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Description . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
Turning Limit Stops On Or Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Programming Limit Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Line Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 5
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8. Use only with the cart, stand, tripod, br
Summary of the content on the page No. 6
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are desi
Summary of the content on the page No. 7
Description The ES30PC/ES31PC Esprit Series is designed to protect camera optics and electronics from moisture and airborne contaminants. The system features a receiver, pan and tilt, enclosure, and a pressurized integrated optics cartridge (IOC). The integrated optics cartridge packages an auto focus camera, lens, heater, and sensors in a small, self-contained unit pressurized to 10 psig with dry nitrogen. MODELS ES30PC16 Standard resolution, color camera with 160X zoom (16X optica
Summary of the content on the page No. 8
Installation ® 1. When installing the ES30PC/ES31PC Esprit system, allow for sufficient clearance between the top of the unit and overhead obstructions. This will prevent interference when the enclosure is driven to its maximum elevation of 33 degrees. MODEL ES30 ES31 16.6 16.9 A (42.5) (42.9) A 33.0° 9.4 9.7 B (23.9) (24.6) 7.1 7.6 B C (18.1) (19.2) 4.2 4.6 D (10.7) (11.7) D C NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. LOOSEN PHILLIPS 2. Re
Summary of the content on the page No. 9
120/230 VOLTAGE SELECTOR SWITCH 4. Route the wires and cables through the center of the Esprit mount. Reinstall the transformer module into the base. The transformer module can be positioned in the mount base in only one orientation. 5. ES30PC-5/ES31PC-5 Models Only – Set the 120/230 voltage selector switch on the transformer to the appropriate voltage. 6. Connect wires and cables. a. Connect to power. Use the two supplied clamp connectors to connect the AC line and neutral. 120/230
Summary of the content on the page No. 10
AUX2 Schematic Drawing USER ESPRIT ACCESSORY K1 OMRON G5V-1-DC12 V1 D1 32 VDC 1N4005 AUX 2 AUX 2 ORANGE WIRE AUX 2 COM AUX 2 COM BLUE WIRE NOTE: CURRENT MUST NOT EXCEED 40 mA. 7. Install mount; refer to the installation manual supplied with the mount for instructions. 8. Turn on the power. If the red LED lights, turn off the power and proceed to the next step. If the red LED does not light, refer to the Troubleshooting section. 9. Plug the male Esprit system connector, located on the bo
Summary of the content on the page No. 11
c. Replace the plug. 11. Refer to the Operation and Programming sections for instructions on how to use your ES30PC/ES31PC Series Esprit integrated positioning system. C311M-N (6/06) 11
Summary of the content on the page No. 12
TXB Series Translator Board Installation (Optional) Pelco’s TXB Series allows controllers from other companies to communicate with the Esprit system. To install a TXB Series board, remove the left cover of the pan and tilt. Once the cover is removed, refer to the manual supplied with the translator board to complete the installation. HOW TO REMOVE THE PAN AND TILT COVER 1. Unscrew the Phillips head screw located on the left cover of the pan and tilt. 2. Remove cover and place to the
Summary of the content on the page No. 13
TOP GASKET FRONT RAIN GUARD C311M-N (6/06) 13
Summary of the content on the page No. 14
Operation POWER-UP DISPLAY When the system is powered up, the selected protocol, revision number, and other information is displayed on the monitor. For example, the screen might show the following information: ESPRIT 16X IOC 2.00 The information displayed depends on the selected protocol (C, D, or P) and the menu selection CONFIGURE DONE for power-up mode. (Refer to the Power-up Mode in the Programming section). D Address 1 P Address 2 The information remains
Summary of the content on the page No. 15
PRESSURIZED INTEGRATED OPTICS CARTRIDGE The pressurized IOC houses an auto focus camera, lens, heater, and sensors in a self-contained, sealed unit. Dry nitrogen pressurized to 10 psig controls the environment inside the cartridge, eliminating internal condensation and corrosion. Sensors strategically placed inside the pressurized IOC continually monitor pressure, temperature, and relative humidity. If internal conditions reach unacceptable levels, an alert label appears on the scree
Summary of the content on the page No. 16
CURRENT READING MENU IOC Internal Reading Temperature 37 C 98 F Dewpoint 08 C 46 F Pressure 10.30 psig 0.71 bar Refresh Exit The Current Reading menu displays the existing status of temperature, pressure, and dewpoint inside the integrated optics cartridge. An asterisk displayed to the left of a menu item denotes that an alert condition exists. Due to the heat emitted from the electronics of the camera, normal temperature operating range is approximately 95°F. PAN AND TI
Summary of the content on the page No. 17
ZONES A zone is a programmed pan area with set boundaries and identifying label. The Esprit system has a maximum of eight zones, each with a 20-character label. Zones can be programmed to blank video when the camera pans into the zone area. If a zone is blanked, the system displays the message, VIDEO BLANK. (Refer to Zone Blank in the Programming section for instructions.) PATTERNS The Esprit system can do either one full pattern (1.5, 3, or 6 minutes long)
Summary of the content on the page No. 18
Programming – ES30PC16/ES31PC16 1. Access main menu (preset 95). Gain/AGC Menu 2. Make main menu selections. Gain Limit 27 Joystick: Move up or down to position cursor or Exit to toggle between selections. Iris Open: Enter. Camera Menu Iris Close: Cancel. Backlight comp Off Zoom limit x- - Reset camera MAIN MENU Auto Iris Menu Next Exit Auto-iris mode Auto Auto-iris level 66 * Auto-iris peak 8 Line Sync Menu Exit
Summary of the content on the page No. 19
Programming – ES30PC22/ES31PC22 1. Access main menu (preset 95). Gain/AGC Menu 2. Make main menu selections. Gain Limit 7 Joystick: Move up or down to position cursor or Exit to toggle between selections. Iris Open: Enter. Camera Menu Iris Close: Cancel. Backlight comp Off Zoom limit x- - Reset camera MAIN MENU Auto Iris Menu Next Exit Auto-iris mode Auto Auto-iris level 66 * Auto-iris peak 16 Line Sync Menu Exit
Summary of the content on the page No. 20
Programming – ES30PCBW24/ES31PCBW24 1. Access main menu (preset 95). Gain/AGC Menu 2. Make main menu selections. Gain Limit 28 Joystick: Move up or down to position cursor or Exit to toggle between selections. Iris Open: Enter. Camera Menu IR Filter Menu Iris Close: Cancel. Backlight comp Off IR Filter mode Auto Zoom limit x72 Auto IR Level Dusk Reset camera Exit MAIN MENU Auto Iris Menu Next Exit Auto-iris mode Auto Auto-iris level
