Harbor Freight Tools 6"OFF ROAD LIGHT 95811 user manual

Summary of the content on the page No. 1

®
6” Off r Oad light
Model 95811
asseMbly and OperatiOn instructiOns
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
tO preVent seriOus injury, read and understand
all warnings and instructiOns befOre use.
© ®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reprodu

Summary of the content on the page No. 2

specificatiOns Steel housing with steel lens rings and steel, rubber supported mounting Materials bracket 7” high at the bracket (mounted/surface) Dimensions 8-1/2” overall height with bracket mounted 4-5/8” Deep Voltage 12 VDC Wire connectors 6” pigtail with split-loom and brass bullet connectors. (Not a fused system) Finish Chrome housing and hardware. Silver reflector with clear (round) glass lens Hardware Yellow-zinc plated Weight about 2 lb. Bulb H-3/55W Halogen (HT201) save this Manual Yo

Summary of the content on the page No. 3

5. do not cut or re-wire any part of the Off road light. 6. light for off road use exclusively. Make certain to follow all local DMV (Depart- ment of Motor Vehicles) laws regarding vehicles and lighting systems. 7. if it is necessary to drill any holes in your vehicle, be sure to read and adhere to the manual of the drill you are using. When drilling holes, beware of any hidden electrical lines or cables. Make sure you do not damage or weaken the structural integrity of the vehicle. 8.

Summary of the content on the page No. 4

1. 2. Installation requires a 1/2” hole through which to insert the wiring. If your vehicle has no hole of this size, then drilling a hole will be necessary. 3. Select a proper location to mount the Off Road Light and mark it. The Light may be either top or bottom mounted. If there is no hole for mounting your Light, you must drill one at the point you have selected. 4. Attach Positive wire (not included) to the proper terminal near the base of the Off Road Light before the Light is mounte

Summary of the content on the page No. 5

Figure 2 Required: Switch/Fuse (not included) rated at 15 amps or larger. Red Positive wire (not included) Fuse Switch Battery Black Ground Wire (6) 7. The red Positive wire (not included) from the Light is the “HOT” wire. Use a pin con- nector or in-line splice connector (both not included) to connect the Off Road Light to your vehicle’s electric wiring system. When using an in-line splice connector, it is not necessary to strip the wires. The wiring diagram in figure 2 will give you a

Summary of the content on the page No. 6

OperatiOn instructiOns Start the engine, turn on the Lights by the on/off switch you installed. inspectiOn, Maintenance, and cleaning 1. warning! Make sure the Power Switch of the Off Road Light is in its “OFF” position and that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 2. befOre each use, inspect the general condition of the tool. Check for loose screws, cracked or broken parts, damaged electrical wiring, and an

Summary of the content on the page No. 7

asseMbly diagraM 3 6 4 7 8 2 1 5 parts list part description Q’ty part description Q’ty 1 Clip 1 6 Black Ground Wire 1 2 Light Assembly 1 7 Rubber Mounting Pads 2 3 Lens Assembly 1 8 Nut/Washer 1 4 Holding Rings 2 9 Housing 1 5 Holding Ring Screws 2 warranty ® Limited 90 d y a arrantyw Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and