Summary of the content on the page No. 1
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Limited Consumer Warranty For a period of one calendar year from the date of purchase of this device, Directed Electronics, Inc. promises to the ORIGINAL PURCHASER to repair or replace (with a comparable reconditioned model), free of cost, any electronic control module which proves to be defective in workmanship or material under normal use, SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLE
Summary of the content on the page No. 4
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUD- ED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COM- MERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLU- SION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WAR- RANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF NON-INFRINGEMENT OF PATENTS, IN THE UNITED STATES OF AMERICA AND/OR ABROAD. NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREW
Summary of the content on the page No. 5
Table of Contents Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 What is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 System Maintenance. . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 6
Standard Configuration controls the Lock/Panic ON/Panic OFF function. controls the Disarm function. controls Silent Mode™and an Auxiliary Output. controls Remote Start. + controls Timer mode. + controls Turbo/Short Run. + controls Channel 4 output. 2 2004 Directed Electronics, Inc. ©
Summary of the content on the page No. 7
What is Included ■ The control module ■ An receiver/antenna ■ Two four-button transmitters ■ The status LED indicator light ® ■ A push-button Valet switch ■ Your warranty registration ■ A shut-down toggle switch Important Information Congratulations on the purchase of your remote start keyless entry system. Due to the complexity of this system, it must be installed by an authorized dealer only. Installation of this product by any- one other than an authorized dealer voids the warranty. All dea
Summary of the content on the page No. 8
System Maintenance The system requires no specific maintenance. Your remote is powered by a small, lightweight 3-volt lithium battery that will last approx- imately one year under normal use. When the battery begins to weaken, operating range will be reduced and the LED on the remote will dim. Your Warranty Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned. M
Summary of the content on the page No. 9
Transmitter Functions The receiver uses a computer-based learn routine to learn the transmitter buttons. This makes it possible to assign any specific transmitter button, or combination of buttons, to any receiver function. The transmitter initially comes programmed with the Standard Configuration, but may also be customized by an autho- rized dealer. The transmitter buttons indicated in all of the instructions in this manual correspond to a Standard Configuration transmitter. Standard Configura
Summary of the content on the page No. 10
Button The remote start function of your system is controlled by pressing this button twice within 3 seconds. and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these but- tons simultaneously. The auxiliary output controls __________________________. Using Your System Warning! Safety First The following safety warnings must be observed at all times: ■ Due to the complexity of this system, installation of this produ
Summary of the content on the page No. 11
must be disabled using the installed toggle switch. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED. These pr
Summary of the content on the page No. 12
has not been properly installed. The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear. All installations must be performed by an authorized Directed Electronics dealer. OPERATION OF THE REMOTE START MOD- ULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMME
Summary of the content on the page No. 13
® The system can also be programmed to arm the optional Failsafe Starter Kill automatically (called Passive Mode). If the system has ® been programmed for Passive Mode, the Failsafe Starter Kill will automatically activate 30 seconds after the ignition has been turned off. After the ignition has been turned off, the status LED will flash rapidly to indicate that the system is in Passive Mode. If Passive Mode has been programmed on, then it is also possible to program the system for Passive Locki
Summary of the content on the page No. 14
Disabling the Starter Kill Without a Transmitter If your remote transmitter is lost or damaged, you can manually override the starter kill. To do this, you must have the vehicle's ® ignition key and know where the Valet switch is located. Be sure ® to check with the installer for the location of the Valet switch. To override the starter kill, turn the ignition on and press the ® Valet switch within 10 seconds. DRW-35 The status LED will stop flashing and the vehicle should start. If it does not
Summary of the content on the page No. 15
® To enter or exit Valet Mode: 1. Turn the ignition on. 2. Turn the ignition off. ® 3. Press and release the Valet DRW-35 switch within 10 seconds. ® The status LED will light steadily if you are entering Valet Mode ® and will turn off if you are exiting Valet Mode. Panic Mode If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transmitter. Just press for 1.5 seconds to enter Panic Mode. In Panic Mode, the horn will honk and the
Summary of the content on the page No. 16
Remote Start This feature allows you to remotely start and run your vehicle for a programmable period of time. This makes it possible to warm up the engine, as well as adjust the interior temperature of the vehi- cle with the climate control system. If interior heating or cooling is desired, the climate controls must be preset, and the fan blower must be set to the desired level prior to remote starting the vehicle. IMPORTANT! (1) Never remotely start the vehicle with the vehicle in gear, and (
Summary of the content on the page No. 17
When you are ready to drive the vehicle: 1. Insert the ignition key and turn it to the ON (not the START) position. 2. Press the brake pedal. NOTE: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. While the vehicle is running during remote start operation, the system will monitor the vehicle and will automatically shut down the engine if the system receives any of the following shut-down inputs: ■ The brake pedal is pressed. ■ The hood is opened. ■ T
Summary of the content on the page No. 18
® Valet Take-Over ® The Valet Take-Over feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate controls on. ® To perform Valet Take-Over: 1. Before turning off the engine, press and release on the transmitter twice in 3 seconds (or press and release the optional momentary switch). 2. Turn the
Summary of the content on the page No. 19
2. Remove your foot from the brake pedal and leave the engine running. 3. Press and release the and buttons at the same time. 4. The lights will flash to indicate the remote start has entered short run turbo mode. 5. Turn off the key, the engine will keep running. 6. Exit and secure the vehicle. 7. The engine will turn off after the programmed run time. Timer Mode By pressing the remote and buttons the parking lights will flash 4 times and then start the vehicle and run for the set duration. T
Summary of the content on the page No. 20
5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires. important!! Timer Mode should be used only in open areas. Never start and run the vehicle in an enclosed space such as a garage or carport. To exit timer mode, turn the ignition switch on any time the engine is running. The parking lights will flash 4 times, indicating timer mode has been exited. 6. The system will start every 3 hours until canceled by the brake, hood, or neutral safety s
