Summary of the content on the page No. 1
VEC021APC
Jump-Start System
260 PSI AIR COMPRESSOR • 12 VOLT DC POWER SUPPLY
OWNER’S MANUAL
& WARRANTY INFORMATION
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USING, READ AND UNDERSTAND
ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS, PLUS YOUR VEHICLE’S
BATTERY MANUFACTURER GUIDELINES. FAILURE TO DO SO COULD RESULT IN INJURY AND/
OR PROPERTY DAMAGE.
4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312
TEL: 954-584-4446 •
Summary of the content on the page No. 2
CONTENTS 1. INTRODUCTION ....................................................................................... 5 2. USING VECTOR™ AS A JUMP-START SYSTEM ......................................... 5,6 2.1 Easy, Step-by-Step Jump-starting Instructions ................................... 7,8 3. CHARGING/RECHARGING ........................................................................ 9 3.1 110/120 Volt AC Charging ................................................................ 9 3.2 12 Volt DC
Summary of the content on the page No. 3
SAFETY INFORMATION WARNING: (Warning statements identify conditions or practices that may result in personal injury or loss of life) 1) When working with lead acid batteries, always make sure immediate assistance is available in case of accident or emergency. 2) Always use protective eyewear when using this product: contact with battery acid may cause blindness and/or severe burns, be aware of first aid procedures in case of accidental contact with battery acid. 3) There is a risk of explosive g
Summary of the content on the page No. 4
CAUTION: (Caution statements advise against certain conditions and practices that may result ® in damage to vehicles, appliances and/or The VECTOR Jump-starter) IMPORTANT: Although this unit is delivered in a partially charged state, you must fully charge it with the supplied 110/120 Volt AC charger for a full 24 hours before using it for the first time. You can not overcharge the unit using the AC charger method. 1) Use only the supplied cords/adapters for recharging this unit. Do not recharge
Summary of the content on the page No. 5
1. INTRODUCTION ® Congratulations on selecting the VECTOR JUMP-STARTER, AIR COMPRESSOR and 12 VOLT DC POWER SUPPLY. This compact jump-starter is unique in the amount of energy it can supply for its size. The internal battery is a high density sealed, lead-acid battery that stores and delivers energy comparable to full sized ordinary jump-starters. Please read this guide carefully before use to ensure optimum performance and avoid damage to the unit or items that you are using it with. A standard
Summary of the content on the page No. 6
1 3 12 2 10 13 9 16 4 5 6 11 15 8 7 14 FIGURE 1A (FRONT VIEW) FIGURE 1B (REAR VIEW) 1. Reverse connection indicator 2. Good connection indicator 3. 12 Volt DC Accessory Socket with 20 amp overload protection 4. Battery Level Push Button 5. LED Charging/Battery Level Indicators 6. Heavy-Duty Welding Quality Jumper Cables 7. Heavy-Duty 450 Amp Copper Clamps 8. Exclusive Quick-Release Clamp Holsters 9. 110/120 Volt UL approved AC/DC Charging Adapter 10. 12 Volt DC/DC Charging Adapter 11. Built-in E
Summary of the content on the page No. 7
® 2. USING THE VECTOR AS A JUMP-START SYSTEM WARNING: 1. Before using this system to jump-start any vehicle or boat, read and understand all instructions, safety tips, warnings, cautions and first aid information provided in this manual and on the product labeling. Additional important information may also be provided by the vehicle’s battery system manufacturer. 2. Be aware of first aid procedures before attempting jump-start procedure. 3. Always wear protective eyewear when working with a lead
Summary of the content on the page No. 8
2.1 EASY, STEP-BY-STEP JUMP-STARTING INSTRUCTIONS 1. Turn OFF vehicle ignition and all accessories (radio, A/C, lights, cell phone, etc.). Place vehicle in park and set the emergency brake. 2. Remove booster clamps from protective holster (Figure 2): simply squeeze the handles and pull down on the clamp. FIGURE 2 3. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (NEGATIVE BATTERY TERMINAL IS CONNECTED TO CHASSIS). 3a. Connect positive (+) red clamp to vehicle battery’s positive terminal.
Summary of the content on the page No. 9
FIRST AID: • SKIN: If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with soap and water. If redness, pain, or irritation occurs, seek immediate medical attention • EYES: If battery acid comes in contact with eyes, flush eyes immediately for a minimum of 15 minutes and SEEK IMMEDIATE MEDICAL ATTENTION 3. CHARGING/RECHARGING ® For maximum battery life, we recommend the VECTOR JUMP-STARTER system is kept fully charged at all time. If the battery is all
Summary of the content on the page No. 10
3.2 12 VOLT DC CHARGING 1. Insert one end of the DC/DC charging adapter into the 12 Volt DC accessory receptacle on the vehicle or boat. 2. Insert the plug at the other end of this charging adapter into the 12 Volt DC accessory socket receptacle on the front panel of the unit. 3. Charge the unit until the green FULL indicator lights when Charge Switch Indicator Button is pressed. DO NOT EXCEED 3-4 HOURS MAXIMUM. 4. When charging is completed, remove the power cord and store in a safe place. 3.3
Summary of the content on the page No. 11
6. AIR COMPRESSOR/TIRE INFLATOR IMPORTANT: Read Instructions Carefully To Avoid Possible Injury Or Property Damage. The built-in 12 Volt DC air compressor is the ultimate compressor for all vehicles, trailer tires and recreational inflatables. Three different sized nozzles are supplied. Each nozzle will clip on the end of the standard tire valve connector located at the free end of the compressor hose. The compressor nozzles are stored inside the hose hatch. The compressor hose with tire fitting
Summary of the content on the page No. 12
IMPORTANT: Always leave the thumb latch in the open position when storing unit. 6.3 INFLATING OTHER ARTICLES (WITHOUT VALVE STEM) Inflation of other items requires use of one of the adapters (nozzles). 1. Open the hatch and remove the nozzles noting their storage positions. 2. Insert appropriate adapter (e.g. needle) into connector (chuck) and close thumb latch. 3. Refer to Table III, Typical Inflation Times, for approximate filling pressure and time. Small items such as volleyballs, footballs,
Summary of the content on the page No. 13
7.1 BULB REPLACEMENT Tools needed - small Phillips screwdriver. 1. Unscrew (counterclockwise) and remove two Phillips screws. 2. Remove the lens cover. 3. Remove the burned-out bulb. 4. Replace with a new bulb (12 Volt 0.2 amp Krypton bulb). 5. Snap the lens cover back into place. 6. Replace (clockwise) the screws and carefully tighten. Do not over tighten! 7.2 BATTERY REPLACEMENT It is recommended that the unit be returned to Vector Customer Service for battery replacement: Contact (954)
Summary of the content on the page No. 14
TWO YEAR LIMITED WARRANTY PROGRAM This limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of Vector Manufacturing, Ltd., regarding this product. There is no other warranty, other than those described herein. This Vector Manufacturing, Ltd. product is warranted, to the original purchaser only, to be free of defects in materials and workmanship for two years from the date of purchase without additional charge. The warranty does not ex
Summary of the content on the page No. 15
15 Vec021APC manual 10/02 15 12/3/02, 10:57 AM
Summary of the content on the page No. 16
© 2002 VECTOR MANUFACTURING, Ltd. • FT. LAUDERDALE, FL 33312 MADE IN CHINA 16 Vec021APC manual 10/02 16 12/3/02, 10:57 AM
