Summary of the content on the page No. 1
™
CS530
Wireless Headset System
User Guide
Summary of the content on the page No. 2
C Co ont nte ent nts s Welcome 3 What’s in the Box 4 Base and Headset Basics 5 Accessories 6 Customize Your Headset 7 Change the Eartip 7 Position Your Headset 7 Connect Your Desk Phone 9 Connect the Power 9 Charge the Headset 9 Connect and Configure Your Desk Phone 10 Desk Phone (standard) 10 Check Configuration and Make a Test Call 11 Desk Phone plus HL10 Lifter (sold separately) 12 Desk Phone plus EHS Cable 14 Position Your Base 15 Your Headset
Summary of the content on the page No. 3
Welcome Congratulations on purchasing your new Plantronics product. This guide contains instructions for setting up and using your CS530 Wireless Headset System. Please refer to the separate safety instructions for important product safety information prior to installation or use of the product. The enclosed DECT 6.0 wireless product uses restricted wireless radio frequencies which vary by country. DECT 6.0 devices are generally authorized for use in The Americas. Use of this DECT 6.0 pro
Summary of the content on the page No. 4
What’s in the Box Base Headset Eartips Power supply Telephone interface cable 4
Summary of the content on the page No. 5
Base and Headset Basics Base overview FRONT BACK 4 1 2 3 5 6 7 8 9 1 Call/mute LED 2 Power on/subscription LED BOTTOM 3 Charging LED 4 Subscription button 5 Narrowband/wideband audio switch 6 Power jack 7 Handset lifter/EHS cable jack 10 8 Telephone interface cable jack 9 Auto answer switch 10 Listening volume dial* 11 Speaking volume dial* 12 Configuration switch* 11 12 * For installation set up Headset overview 1 2 3 4 5 1 Volume up button 2 Volume down button 3 Call control
Summary of the content on the page No. 6
Accessories 1 2 1 Electronic Hookswitch Cable (EHS) Electronically takes your desk phone handset off hook. Enables remote call answer/end with your headset. 2 HL10™ Lifter Automatically lifts handset and returns it to the cradle. Enables remote call answer/end with your headset 6
Summary of the content on the page No. 7
Customize Your Headset Customize the headset by changing the eartip, wearing it on the right or left and optimizing the position of the microphone. Change the Eartip 1 The headset comes with a pre-installed eartip. To install a different eartip see the following: Remove the pre-installed eartip by pushing in and turning the eartip CLOCKwise, then pull firmly. 2 Choose the size and style of eartip that fits most comfortably. Align eartip tabs with notches in headset. Push in firmly and twist
Summary of the content on the page No. 8
2 Rotate the microphone boom until it is pointed toward your mouth. Left Ear Wearing 1 The headset can be converted for wearing on left ear as follows: 2 Turn microphone boom around. 3 Rotate microphone boom down. 8
Summary of the content on the page No. 9
Connect Your Desk Phone This section describes how to connect the base to your desk phone. Connect the Power Plug one end of the power supply into the power jack on the back of the base and the other end into a working power outlet. The Power On LED will be solid white. Charge the Headset Place the headset in the charge cradle. The charging LED on the base will flash green when charging and turn solid green when the headset is fully charged. Charge for at least 20 minutes prior to the first
Summary of the content on the page No. 10
Connect and Configure Your Desk Phone There are three setup options for connecting the CS530 to your desk phone. Select one of the following and continue. • Desk phone (standard) • Desk phone + HL10 lifter (sold separately) • Desk phone + EHS cable (sold separately) NOTE If you will be using a standard desk phone set up or a desk phone with an HL10 lifter, continue below. If you will be using the desk phone with an EHS cable, refer to Desk phone plus EHS cable section in this guide. For
Summary of the content on the page No. 11
Check Configuration and Make a Test Call 1 If your desk phone has a volume control set it to mid-range. 2 Look at the bottom panel of your base and make sure the default settings are correct. Set your desk phone’s volume also. listening volume dial ( ) = 2 and speaking volume dial ( ) = 2 configuration switch = A desk phone volume = mid-range 3 Remove the handset from desk phone cradle. 4 While wearing your headset, press the call control button on the headset. 5 If you do not hear a dial t
Summary of the content on the page No. 12
Desk Phone plus HL10 Lifter (sold separately) NOTE First follow the steps above for Desk Phone (Standard). 1 Firmly press the handset lifter power cord into the handset lifter jack. USE 2 While wearing your headset, slide the handset lifter arm under the handset until the lifter base touches the side of the phone. 3 Slide the lifter up to where it nearly touches the handset earpiece. 4 Press the call control button on your headset to activate the lifter. 5 If you hear a dial tone the lifter i
Summary of the content on the page No. 13
1 2 If You Do Not Hear a Dial Tone 1 If you do not hear a dial tone, raise the lifter height switch to the next highest position. 2 Repeat steps 2 through 5 above as necessary until you hear a dial tone. 3 When you hear a dial tone, secure the lifter as described in steps 6 though 8. Additional Parts (if required) Use extender arm when the handset lifter needs additional stability lifting and returning handset to cradle. Extender Arm 1 Slide extender arm onto lifter. 2 Stabilizers can be shif
Summary of the content on the page No. 14
For Nortel Phones Only Desk Phone plus EHS Cable 1 Connect the end of the EHS cable to the base and the other end to the desk phone as described in the EHS Adapter Getting Started guide. NOTE For further installation information refer to the EHS Getting Started guide that came with your EHS cable or at plantronics.com/accessories. 1414
Summary of the content on the page No. 15
Position Your Base The minimum recommended separation between your desk phone and the base is 6 inches. The minimum recommended separation between the base and computer is 12 inches. Incorrect position can cause noise and interference problems. 15
Summary of the content on the page No. 16
Your Headset Now that you’ve adjusted your headset and connected your desk phone, read this section to learn about the headset features, how to use the controls and more. Headset Controls 1 2 3 5 4 1 Volume up Increase the volume Press the volume button up + 2 Volume down/Mute button Decrease the volume Press the volume button down – Mute/unmute a call To mute/unmute the headset, press the volume button down – for 1.5 seconds 3 Call control button Place, answer, end a call Press the call c
Summary of the content on the page No. 17
Low Battery Warning If you are on a call and the headset battery is critically low, you will hear a repeated single low tone every 15 seconds indicating that the battery is low. You should recharge the headset immediately. If you are not on a call and press the call control button, you will hear three low tones if the battery is critically low. You should recharge the headset immediately. Muting Your Headset During a Call To mute/unmute the call, press the volume button down – for 1.5 seco
Summary of the content on the page No. 18
Your Base Base Phone Button and Switches 1 2 3 1 Subscription Button The headset and base that came in the box are subscribed (connected) to each other. However, if you wish to use a new headset or need to restore subscription to your current headset, the units can be subscribed to each other by the following two methods. Automatic Secure Subscription With your system idle, docking a headset will automatically subscribe it to the base, making it the primary headset. The Power On/Subscription
Summary of the content on the page No. 19
2 Wideband/Narrowband Audio Switch The CS530 has wideband audio, which allows speech to sound clearer and more natural. If your desk phone is capable of wideband audio, set the Wideband-Narrowband audio switch to yellow for wideband. NOTE: Talk time will be reduced when operating in wideband mode. Set the switch to black (narrowband) for longer headset battery life or to increase the number of systems that can work in a small area. 3 Auto Answer Switch Auto answer saves a button press to es
Summary of the content on the page No. 20
Daily Use Place an Outgoing Call 1 Wearing your headset, press the headset call control button. 2 Remove the handset from the cradle. You will hear a dial tone. NOTE This step will be automatic if you install a lifter or EHS cable accessory. For a complete list of accessories, visit plantronics.com/accessories. 3 Dial the number using your desk phone. 4 To end the call, press the headset call control button and hang up the handset. Answer an Incoming Call 1 Wearing your headset, press the he
