Summary of the content on the page No. 1
Cintiq20WSX_Manual.fm Page -1 Monday, January 15, 2007 9:23 AM
Installation Guide & Hardware Manual
for Cintiq 20WSX (DTZ-2000W)
Summary of the content on the page No. 2
Cintiq20WSX_Manual.fm Page 0 Monday, January 15, 2007 9:23 AM ® Wacom Cintiq 20WSX Installation Guide & Hardware Manual for Cintiq 20WSX (DTZ-2000W) English version 1.0, January 15, 2007 Copyright Wacom Company, Limited, 2007 All rights reserved. No part of this manual may be reproduced except for your express personal use. Wacom reserves the right to revise this publication without obligation to provide notification of such changes. Wacom does its best to provide current and acc
Summary of the content on the page No. 3
Cintiq20WSX_Manual.fm Page 1 Monday, January 15, 2007 9:23 AM INTRODUCTION AND OVERVIEW ® ® The Wacom Cintiq 20WSX pen display combines the benefits of an LCD monitor with the control, comfort, and productivity of Wacom’s cordless, battery-free pen technology. This gives you a direct ® pen-on-screen interface that can be used with a Personal Computer (PC) or Macintosh computer. Cintiq’s basic components include a Wacom pen tablet internally mounted behind a 20.1" w
Summary of the content on the page No. 4
Cintiq20WSX_Manual.fm Page 2 Monday, January 15, 2007 9:23 AM PRECAUTIONS ON USE AND HANDLING Be sure to follow all instructions, cautions, and warnings found within this manual. Failure to do so could cause the loss of data or damage to your computer. Failure to do so could also void your warranty, in which case Wacom shall have no responsibility to repair or replace the product. Physical location Do not use the Cintiq pen display in a facility c
Summary of the content on the page No. 5
Cintiq20WSX_Manual.fm Page 3 Monday, January 15, 2007 9:23 AM Handling WARNING High Voltage. Do not open or disassemble the Cintiq pen display. There is a risk of electrical shock when the casing is open. This will also void your warranty and Wacom shall have no responsibility to repair or replace the product. WARNING Do not operate the display stand incline adjustment levers when Cintiq is not mounted on the stand, and do not lift the stand
Summary of the content on the page No. 6
Cintiq20WSX_Manual.fm Page 4 Monday, January 15, 2007 9:23 AM CAUTION Do not put heavy articles on the pen display or push against it with a strong force; this may damage the display screen or break the Cintiq stand locking mechanism. Do not place heavy articles on the Cintiq cabling, repeatedly bend the cables sharply, CAUTION or apply heavy stress to the cable connectors; this may damage the unit or cabling. CAUTION Do not store the pen display tablet on a sur
Summary of the content on the page No. 7
Cintiq20WSX_Manual.fm Page 5 Monday, January 15, 2007 9:23 AM CONTENTS Introduction and overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Precautions on use and handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Physical location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Usage . . . . . . . . . .
Summary of the content on the page No. 8
Cintiq20WSX_Manual.fm Page 6 Monday, January 15, 2007 9:23 AM Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Caring for Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Optional display configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Using an alternate mount or stand . . . . . . . . . . . . . . . . . . . . . . . . . 57 Pen and digital ink capabilities in Windows Vista
Summary of the content on the page No. 9
Cintiq20WSX_Manual.fm Page 7 Monday, January 15, 2007 9:23 AM UNPACKING YOUR CINTIQ Package contents You will find parts and accessories packed together in the accessories box. To avoid damaging your product, please review the instructions on the following pages before setting up or using Cintiq or the Cintiq stand. Your product came with the following items: Cintiq stand (MST-A103) *Patented Cintiq 20WSX (model DTZ-2000W) pen display, main unit with attached cable Parts and
Summary of the content on the page No. 10
Cintiq20WSX_Manual.fm Page 8 Monday, January 15, 2007 9:23 AM Setting up the Cintiq stand Place the stand on your desktop or work surface, making sure the stand is stable and will not tip or fall when the pen display is mounted on it. Then familiarize yourself with the stand components. WARNING Do not operate the incline adjustment levers when Cintiq is not mounted on the stand, and do not lift the stand by the adjustment levers; the stand is spring-loaded and may cause injury or da
Summary of the content on the page No. 11
Cintiq20WSX_Manual.fm Page 9 Monday, January 15, 2007 9:23 AM Unpacking and mounting the Cintiq pen display Remove any packing materials from the back of the display unit and cabling. To mount Cintiq on the stand: • Make sure the stand is stable on your desktop or other work surface and will not tip or fall when Cintiq is mounted on it. • Securely grasp Cintiq with both hands so that the display faces toward you, with the power switch and LEDs located at the top. • Align Cin
Summary of the content on the page No. 12
Cintiq20WSX_Manual.fm Page 10 Monday, January 15, 2007 9:23 AM WARNING When operating the incline adjustment levers, Cintiq must be mounted on the stand with the stand feet resting on a – B – stable, flat surface. The stand is spring-loaded and can snap back quickly, causing injury or damage if not operated properly. After the display unit has been mounted on the stand, remove the foam blocks that lock the adjustment levers in place. Save these blocks with the other packaging
Summary of the content on the page No. 13
Cintiq20WSX_Manual.fm Page 11 Monday, January 15, 2007 9:23 AM Adjusting rotation The pen display can be rotated on the display stand when the incline is less than or equal to 25 degrees. To adjust rotation, grasp Cintiq by the main body and rotate the unit to the desired position; it will move on the bearing hub. You can only rotate the display unit 180 degrees in either direction. If you do not plan to rotate the Cintiq, use the rotation lock screws to fasten the display to th
Summary of the content on the page No. 14
Cintiq20WSX_Manual.fm Page 12 Monday, January 15, 2007 9:23 AM Removing Cintiq from the display stand To remove Cintiq from the display stand: • If the rotation lock screws are attached, remove them from the back of Cintiq. • Position the pen display to landscape orientation before removing it from the display stand. The stand will not release unless Cintiq is in landscape orientation. • Next, raise the stand incline to the highest position. See Adjusting the display incline on page 10 fo
Summary of the content on the page No. 15
Cintiq20WSX_Manual.fm Page 13 Monday, January 15, 2007 9:23 AM CINTIQ PEN DISPLAY COMPONENTS After the Cintiq pen display is safely mounted on the Cintiq stand, take some time to familiarize yourself with its features and components. The LCD monitor and tablet sensor function as an integrated input and output device. The LCD monitor supports resolutions up to 1680 x 1050 pixels at 16.7 million colors. The tablet sensor reports pen coordinates, pressure, tilt, switch, eraser, and other in
Summary of the content on the page No. 16
Cintiq20WSX_Manual.fm Page 14 Monday, January 15, 2007 9:23 AM Rear view On Screen Display (OSD) controls These controls enable you to adjust a variety of display settings. See Adjusting the LCD monitor on page 36 for more information. Integrated pen holder and alternate cable exit The pen can be stored here. If you are not using Digital/Analog (DVI/VGA) switch the Cintiq stand supplied with the unit, you can Set this switch for the video route the cable to exit from this location. See
Summary of the content on the page No. 17
Cintiq20WSX_Manual.fm Page 15 Monday, January 15, 2007 9:23 AM INSTALLATION System requirements Before installing Cintiq, make sure your computer meets the following minimum system requirements: • PC. Windows Vista™, Vista x64, XP, XP x64, or 2000. DVI or VGA video connector, available USB port, and CD-ROM drive. • Macintosh. OS X, v10.3.9 or greater. DVI or VGA video connector, available USB port, and CD-ROM drive. ADC connectors require an ADC to DVI-I adapter, not included. (ADC t
Summary of the content on the page No. 18
Cintiq20WSX_Manual.fm Page 16 Monday, January 15, 2007 9:23 AM Step 1: LCD monitor installation In the first stage of the installation process, Cintiq is installed as a monitor on your system. As you work through the first stage of the installation process, please refer to the LCD monitor cabling diagram on page 18 when making cable connections. Important: Do not connect the USB data cable until instructed to do so. • Turn off your computer. Caution: Never connect or disconnect the video or
Summary of the content on the page No. 19
Cintiq20WSX_Manual.fm Page 17 Monday, January 15, 2007 9:23 AM If you are connecting to an Apple computer with one of the following video ports, you will need to use an adapter: If you are connecting to an ADC connector, you will need to obtain an ADC to DVI-I adapter. Plug the Cintiq video cable into the ADC to DVI-I adapter. Then plug the ADC adapter end into the ADC connector Apple ADC on your video card. connector If you are connecting to an Apple mini-VGA connector, you will need
Summary of the content on the page No. 20
Cintiq20WSX_Manual.fm Page 18 Monday, January 15, 2007 9:23 AM LCD monitor cabling diagram DIGITAL/ANALOG (DVI/VGA) switch – A – CAUTION Make sure your video card has a DVI or VGA connector, and that you correctly set the Cintiq Digital/Analog (DVI/VGA) switch for the video connector you are using. Do not attach the USB data cable until instructed to do so. Cintiq, rear view Video card DVI or VGA – B – – C – DC INput DVI-I connector To connect to a DVI-D connector, use the
