Summary of the content on the page No. 1
RoyalTek
Data Log GPS Receiver
RGM-3800
User Manual
Version 1.0
Published on May 2007 by RoyalTek Company Ltd.
Design and specification are subject to change without notice.
Summary of the content on the page No. 2
Content 1. Product Introduction ................................................................3 1.1 Overview..........................................................................................................3 1.2 Main Features...................................................................................................3 1.3 Product Notification.........................................................................................3 1.4 Application...........................
Summary of the content on the page No. 3
1. Product Introduction 1.1 Overview RoyalTek Data log GPS receiver, RGM-3800, is the successor of well-known Data log GPS receiver in 2007. RGM-3800 can receive and record time, date, position and altitude information. It uses SIRF Star III extreme fast TTFF GPS engine and provide accurate position tracking solution. 1.2 Main Features SiRF Star III GPS chipset 20 parallel channels LED to show the status of GPS, Battery and Power. USB Interface. Memory storage could
Summary of the content on the page No. 4
2. Specification 2.1 Specification Specification GPS Chipset Sirf GSC3f/LP Frequency L1, 1,575.42 MHz Channel 20 parallel C/A Code 1,023 MHz Fix time Reacquisition: less than 1s (Open Hot start: less than 1s SKY,typical) Warm start: less than 35s Cold start: less than 42s Accuracy Position: within 10m for 90% Velocity: 0.1m/s Interface Protocol Output message: NMEA 0183 ver. 3.0,GGA, GSA, RMC and GSV every 1s, Baud rate 115200bps DGPS WAAS, EGNOS Trickle power Disable
Summary of the content on the page No. 5
(when used at *Operating time may differ depending on the situation or the 25ºC) environment condition. Mechanical Dimension Dimension: 70mm x 36.6mm x 24mm Weight <=50g (without battery) Location Log Log data UTC Time, Longitude, Latitude, Altitude, Velocity Log Interval 5secs ~ 60secs, user configurable (Default 15secs) Stored Data Type There are three types setting for intervals. (User configurable) For the data type, there are 3 options data logger format that can be used. Defa
Summary of the content on the page No. 6
2.2 Check the Package Content Before you start using RGM-3800, please check out if your package includes the following items. If any item is damaged or missed, please contact your reseller at once. ● RGM-3800 Data log GPS receiver ● CD (user manual, SW utility) ● USB Cable ● String (optional)
Summary of the content on the page No. 7
2.3 Hardware Overview Mini USB Connector Antenna Location LED for GPS Status, Battery Status And Memory Status Memory Clear Button Power Button
Summary of the content on the page No. 8
2.4 Detailed Hardware Function 2.4.1. Power Switch Power ON / Power OFF 2.4.2. USB Jack Using the supplied USB cable to connect with the GPS receiver ‘s USB connector for data transfer. USB Cable is without the charging function. 2.4.3. Memory Clear button While the power turn on, you can push the clear button for 3 seconds to erase the GPS log files from the recording memory if the GPS Receiver battery is ok. 2.4.4. Memory Status LED (Amber) Glowing Amber color indicat
Summary of the content on the page No. 9
lower than 1%), the Battery LED flashes more frequently and please replace the batteries. If Battery low, The RGM-3800 will stop to log GPS position data. 2.5. Usage Tip 2.5.1. Inserting the Battery Insert the batteries with the correct polarity +/- 2.5.2. Turn on Receiver and Wait for GPS Fix When user use the GPS Receiver, direct and hold the antenna side upward or outward Note: The receiver can’t receiver the gps signal when it is in the metallic bag, or when it is
Summary of the content on the page No. 10
Place new AAA battery into the room of RGM-3800. Be sure not to drop the battery. Battery duration can last Approx. over 10 hours in continuous operation mode (when used at 25ºC). Cautions: Remove the batteries when you do not use the RGM-3800 for a long time. Otherwise, it may result in leakage of the batteries.
Summary of the content on the page No. 11
3. Software Installation and Usage The Main Menu of Installation CD shows as above. Click the Install USB Driver to install the USB Driver, which is needed when you connect the RGM-3800 to your PC or Notebook. Click the PC Software to install the software application. Click the User Manual to open the user manual of RGM-3800. Click the View Royaltek Website to link our http://www.royaltek.com, please make sure your PC connects to Internet first. Click the Browse CD Con
Summary of the content on the page No. 12
3.1 Install USB Driver Install the USB Driver from CD. When screen shows the installation window as follows: Click “Next> to next page”, or click”
Summary of the content on the page No. 13
Summary of the content on the page No. 14
3.2 Install Data download Utility Click “Next> to next page”, or click”” to next page, or click”
Summary of the content on the page No. 15
Click “Install” to start installation. Or click”
Summary of the content on the page No. 16
Start installation. Please click “Finish” to finish the Installation.
Summary of the content on the page No. 17
Finally you will see the icon on Programs menu. 3.3 Install locr PC Client Utility To the License Agreement page: Click “Accept” to start installation, or click ”Don’t Accept” to give up installation. Then
Summary of the content on the page No. 18
Start installation. Click “Next> to next page”, or click”
Summary of the content on the page No. 19
Select Installation folder and Click “Next> to next page”, or click” to start installation”, or click”
Summary of the content on the page No. 20
locr PC Client is being installed Installation Complete
