Summary of the content on the page No. 1
Distributed by
Any reference to Raytheon or
RTN in this manual should be
interpreted as Raymarine.
The names Raytheon and RTN
are owned by the
Raytheon Company.
Summary of the content on the page No. 2
Raystar 112LP GPS Transducer Installation Guide Covers: E32001 SeaTalk Version E32002 NMEA Version
Summary of the content on the page No. 3
Raystar 112LP GPS Transducer Installation IMPORTANT NOTICE This device is only an aid to navigation. Its accuracy can be affected by many factors, including equipment failure or defects, environmen- tal conditions and improper handling or use. It is the user’s responsibility to exercise common prudence and navigational judgement, and this device should not be relied upon as a substitute for such prudence and judgement. Package Contents Checking your Raystar 112LP Package The Raystar 112LP packa
Summary of the content on the page No. 4
Raystar 112LP GPS Transducer Installation Summary of Features Receiver type: 12 Parallel channels Frequency: 1575.42 MHz +/- 1 MHz (C/A code), L1 Sensitivity: -130dBm Signal acquisition: Automatic Time to first fix: 15 minutes maximum, typically 2 minutes Position accuracy: 15m RMS. (L1, C/A code HDOP <2.5 without SA) Speed accuracy: 0.5m/s RMS. (L1, C/A code HDOP <2.5 without SA) Geodetic Datum: WGS-84 (190 alternatives programmable) Cable length: 10m (33ft) 0 0 Operating Temp.: -10 to 70 C (
Summary of the content on the page No. 5
Raystar 112LP GPS Transducer Installation This page left intentionally blank
Summary of the content on the page No. 6
Raystar 112LP GPS Transducer Installation Raytheon Raystar 112LP GPS Receiver This booklet covers two models of the Raystar 112LP SeaTalk Version Part No. E32001 NMEA Version Part No. E32002 Before commencing installation ensure you have the correct unit for your application. Raytheon Marine cannot be responsible for incorrect operation due to incorrect unit specification. Always state which model you have when making any communication with Raytheon or a registered service agent. GPS Transducer
Summary of the content on the page No. 7
Raystar 112LP GPS Transducer Installation Surface Mounting 1. Select a suitable area which allows access to the underside of the mounting surface for fixing and, using the template supplied in this document, carefully drill the two 6mm (0.25in) fixing holes marked. 2. If the cable is to pass through the mounting surface drill the 6mm (0.25in) or 19mm (0.75”) centre hole depending on whether the plug has to pass through the surface or not. If the cable is to exit from the side of the GPS above th
Summary of the content on the page No. 8
Raystar 112LP GPS Transducer Installation Pole/Rail Mounting 1. Screw the pole mount base to a suitable pole or rail mount bracket which has an industry standard 1” 14TPI thread until secure. 2. Pass the cable through the centre hole of the pole mount base (A) or through the cable exit hole alongside the centre hole (B) or insert the cable into the side exit channel (C). 3. Check the cable is positioned correctly and secure the receiver to the pole base using the two screws provided. Note: An o
Summary of the content on the page No. 9
Raystar 112LP GPS Transducer Installation Connections NMEA Version Connection is made via a 10m (33ft) cable terminated with a moulded 6 pin connector. 3 Screen (0V/ground) 2 Screen 4 Yellow (0V/ground) (NMEA out)) 1 Red 5 Green (Power ) (NMEA in) 6 Brown (RTCM in) D4192-1 SeaTalk Version Connection is made via the 10m (33ft) cable with bare ends suitable for connection to an existing SeaTalk bus. Red (12V) Yellow (SeaTalk input/output) Brown (RTCM in) Green (not connected) Screen (0V/ground) D4
Summary of the content on the page No. 10
Raystar 112LP GPS Transducer Installation Raytheon Raystar 112LP GPS Receiver Mounting Template 36mm (1.4in) 19mm (0.75") dia. for NMEA plug 18mm (0.7in) 6mm (0.25") dia. 6mm (0.25") dia. 2 positions for cable only Cable Exit Channel D4194-1 Note: Access to the underside of the mounting surface must be available to allow for secure fixing. 36mm (1.4in) 18mm (0.7in)
Summary of the content on the page No. 11
Raystar 112LP GPS Transducer Installation This page left intentionally blank
Summary of the content on the page No. 12
Raystar 112LP GPS Transducer Installation EMC Installation & Service Guidelines All Raytheon equipment and accessories are designed to the best industry standards for use in the leisure marine environment. Their design and manufacture conforms to the appropriate Electro- magnetic Compatibility (EMC) standards, but good installation is required to ensure that performance is not compromised. Although every effort has been taken to ensure that they will perform under all conditions, it is important
Summary of the content on the page No. 13
Document Number: 81144-1 Raytheon Marine Company 676 Island Pond Road Manchester, NH 03109-5420 USA TEL (603) 647-7530 FAX (603) 634-4756 http://www.raymarine.com Raytheon Marine Europe Ltd. Anchorage Park, Portsmouth Hampshire, PO3 5TD England TEL +44 (0) 1705 693611 FAX +44 (0) 1705 694642 Printed in England
