Summary of the content on the page No. 1
COLOR DGPS/PLOTTER
COLOR GPS/PLOTTER
GP-1850WD, GP-1850W FURUNO/NAVIONICS
GP-1850WD, GP-1850W FURUNO/C-MAP NT
Summary of the content on the page No. 2
Your Local Agent/Dealer Your Local Agent/Dealer 9-52 Ashihara-cho, 9-52 Ashihara-cho, Nishinomi Nishinomiy ya, Ja a, Jap pan an Tele Telep phone : hone : 0798-65-2111 0798-65-2111 Telefax : Telefax : 0798-65-4200 0798-65-4200 FIRST EDITION : FIRST EDITION : A AUG. UG. 2002 2002 A All ri ll rig ghts reserved. hts reserved. Printed in Japan Printed in Japan B : B : A AUG. UG. 28,2002 28,2002 PUB.No. PUB.No. OME-44250 OME-44250 *00080936500* *00080936500* *00080936500* *0008093650
Summary of the content on the page No. 3
SAFETY INSTRUCTIONS W WARNING ARNING CAUTION Do not use the equipment for other than Do not open the equipment. its intended purpose. Hazardous voltage which can cause No one navigation device should ever be electrical shock, burn or serious injury solely replied upon for the navigation of exists inside the equipment. Only qualified personnel should work inside the equipment. a vessel. Do not disassemble or modify the Always confirm position against all available equipment. aids to
Summary of the content on the page No. 4
TABLE OF CONTENTS 4.4 Erasing Marks...............................4-3 FOREWORD .................................. iv 4.5 Displaying Track and Mark Points............................................ 4-4 SYSTEM CONFIGURATION ......... v 4.6 Target Mark...................................4-4 WHAT IS WAAS?........................... vi 5. WAYPOINTS 5.1 Entering Waypoints.......................5-1 1. OPERATIONAL OVERVIEW 5.2 Erasing Individual Waypoints.........5-4 1.1 Display Unit Contro
Summary of the content on the page No. 5
TABLE OF CONTENTS 10. CUSTOMIZING YOUR UNIT 10.1 CHART SETUP OPTIONS menu 10-1 10.2 DISPLAY OPTIONS menu...........10-3 10.3 GPS/DGPS/TD OPTIONS menu ...........................................10-4 10.4 CONFIGURATION menu.............10-8 11. USING C-MAP NT MODEL 11.1 Inserting Chart Card ................... 11-1 11.2 Cursor and Data Display ............ 11-2 11.3 Tidal Information..........................11-3 11.4 Navigation to Ports, Port Services...........................
Summary of the content on the page No. 6
FOREWORD Navigation information is displayed on a A Word to GP-1850WD/1850W bright 6.5-inch color TFT LCD. On-screen Owners information shown are position, range and Congratulations on your choice of the bearing to cursor position, range, bearing, FURUNO GP-1850WD COLOR ETA and TTG to waypoint, etc. DGPS/PLOTTER, GP-1850W COLOR A high sensitivity receiver tracks up to twelve GPS/PLOTTER. We are confident you will (WAAS: thirteen) satellites simultaneously. see why the FURUNO name ha
Summary of the content on the page No. 7
SYSTEM CONFIGURATION GPA-017 GPA-019 (GP-1850W) (GP-1850WD) ANTENNA UNIT Receives signal from GPS satellite and beacon reference station. (GP-1850WD only) DISPLAY UNIT External equipment (Autopilot, etc.) DGPS beacon receiver (GP-1850W only) Rectifier PR-62 Ship's mains Ship's mains 100/110/115/220/230 VAC 12-24 VDC 1 , 50/60 Hz v
Summary of the content on the page No. 8
WHAT IS WAAS? WAAS, available in North America, is a provider in the worldwide SBAS (Satellite Based Augmentation System) navigation system. An SBAS provider furnishes GPS signal corrections to SBAS users. Two more SBAS providers are also currently under development, MSAS (Multi-Functional Satellite Augmentation System) for Japan and EGNOS (Euro Geostationary Navigation Overlay Service) for Europe. All providers will be compatible with one another, thus providing “seamless” position fixe
Summary of the content on the page No. 9
1. OPERATIONAL OVERVIEW This chapter acquaints you with the basics of your unit - from turning on the power to the soft key menu operation. 1.1 Display Unit Controls • Registers own ship's positions. • Marks man overboard position, event position. Cursor pad Registers items • Shifts cursor and display. on menus. • Selects items on menus. SAVE MOB ENTER ABC DEF GHI 1 2 3 Enter alphanumeric data. JKL MNO PQR Soft key's functions change 5 4 6 depending on the display. STU VWX YZ& 7 8 9 _'# CL
Summary of the content on the page No. 10
1. OPERATIONAL OVERVIEW 1.2 Remote Controller Inscribes waypoints. MOB Inscribes MOB mark. Displays alarm SAVE ALARM menu. SW 1 ABC 1 DEF 2 GHI 3 Enter, cancel, clear SW 2 JKL 4 MNO 5 PQR 6 alphanumeric data. Soft keys SW 3 STU 7 VWX 8 YZ 9 SW 4 _'#0 ENTER MENU SW 5 CLEAR ZOOM IN/OUT Expand, shrink Shows/hides soft chart. SHOW key menu. CANCEL HIDE Adjust brilliance. Functions same BRILL CENTER as cursor pad. Adjust tone. Displays the waypoint & WPT PLOT route menu. TONE XTE/ RTE HIWAY Not
Summary of the content on the page No. 11
1. OPERATIONAL OVERVIEW 1.3 Inserting Mini Chart 1.4 Turning the Power Card On/Off Insert appropriate mini chart card before Turning the power on turning on the power. Press the [POWER/BRILL] key at bottom left-hand side of the display unit to turn on Note: Static electricity can be passed the power. When the unit is turned on, it through your fingers to a memory card proceeds in the sequence shown in the and destroy the contents of the card. figure in below, after displaying the FU
Summary of the content on the page No. 12
1. OPERATIONAL OVERVIEW When the satellite signal is being received 1.5 Adjusting Tone and normally, the GP-1850WD/1850W displays Brilliance various abbreviations at the bottom left-hand 1. Press the [POWER/BRILL] key with a corner of the display which show DGPS/GPS touch-and-release action. The tone and receiver status. The table in below shows brilliance setting window appears. these abbreviations and their meanings. Functions Display abbreviations Indication Meaning TONE 2
Summary of the content on the page No. 13
1. OPERATIONAL OVERVIEW 1.6 Plotter Displays 1.7 Steering/Highway Displays Press the [PLOT] key. Each time this key is pressed, the display mode changes in the Press the [XTE/HIWAY] key. Each time this sequence shown below. For display mode, key is pressed, the display mode changes in refer to Chapter 2. the sequence shown below. For display NORTH mode, refer to Chapter 2. UP ZOOM IN ZOOM OUT CROSS COURSE TRACK QP<01> UP 230 240 250 260 WP-002 FISH BRG RNG 245.0 ° 27.2 nm BRIDGE
Summary of the content on the page No. 14
1. OPERATIONAL OVERVIEW 3. Select item with the cursor pad, and 1.8 Menu Operation, Soft press the EDIT soft key. For example, Keys select TIME DISPLAY. Most operations are carried out through the TIME DISPLAY menu which is opened and closed with the [MENU] key. Menus may be selected with 12 HOUR the five soft keys to the right of menus. 24 HOUR Options are selected with the cursor pad. Time display window 1. Press the [MENU] key to display the main menu. 4. Use the cursor
Summary of the content on the page No. 15
1. OPERATIONAL OVERVIEW EDIT soft key. Select how you want the 1.9 Demonstration Display courseline to be traced; by FIGURE 8 or The demonstration display provides DIR.(ection). For DIR., enter course. simulated operation of this unit. On the 10. Press the ENTER soft key or [ENTER] plotter display, own ship tracks, at the speed key. selected, a figure eight course or any course 11. Select DEMO START LAT, and press the you enter, starting from position entered. All EDIT soft key.
Summary of the content on the page No. 16
1. OPERATIONAL OVERVIEW This page is intentionally left blank. 1-8
Summary of the content on the page No. 17
2. PLOTTER DISPLAYS screen and points to north. A filled triangle 2.1 Presentation Modes marks own ship’s position. The plotter display mainly shows chart, ship’s track, waypoints, and navigation data. When destination is not set, the course is upward on the screen at the moment the Three types of display presentations are course-up mode is selected. provided for the normal plotter display: COURSE 34° 12.345' N CSE 245.8° north-up, course-up and auto course-up. To 16.3kt 135° 12.3
Summary of the content on the page No. 18
2. PLOTTER DISPLAYS 2.2 Cursor 2.3 Shifting the Display Turning on the cursor, shifting the The display can be shifted on the plotter cursor display. Press the cursor pad to turn the cursor on, 1. Press the cursor pad to display the and the cursor appears at the own ship’s cursor. position. Operate the cursor pad to shift the 2. Locate the cursor at a screen edge. The cursor. The cursor moves in the direction of screen shifts in the direction opposite of the arrow or diagonal pr
Summary of the content on the page No. 19
2. PLOTTER DISPLAYS 2.5 Selecting Chart 2.6 Mini Chart Cards Scale/Range The mini chart cards contain nautical charts. When you insert a suitable mini chart card in Chart scale (range) may be selected with the the slot and your boat is near land, a chart ZOOM IN or ZOOM OUT soft key. ZOOM IN appears. expands the chart; ZOOM OUT shrinks it. When a wrong card is inserted or a wrong chart scale is selected, the land will be hollow. Insert the proper card and select a sui
Summary of the content on the page No. 20
2. PLOTTER DISPLAYS FURUNO chart symbols Symbol Description Summit Wreck Lighthouse Lighted Buoy Buoy Sample chart (Japan and South Korea) Radio Station showing indices Position of Sounding Remarks on chart display Obstruction A chart will not be displayed in the following Fishing Reef conditions: • When the chart scale is too large or too Platform small. Anchorage When this happens, select proper chart scale. TM Comparison of FURUNO and Nav-Charts • When scrolling the
