Summary of the content on the page No. 1
Summary of the content on the page No. 2
TABLE OF CONTENTS SECTION ONE SECTION FIVE Safety Instructions…………………………. 1-5 Exploded View……………………….….. 19 Placement of the grill……………………….. 5 Parts List ………………………………… 20 SECTION TWO SECTION SIX Side Shelf Assembly……………………….. 6 Grilling Hints …………………………….. 21 Side Shelf Handle & Grease Tray Handle G
Summary of the content on the page No. 3
PRECAUTIONS SAFETY INSTRUCTIONS RECOGNIZED SAFETY SYMBOLS, WORDS AND LABELS WARNING WARNING Do not try lighting this ap pliance without first reading the “LIGHTING INSTRUCTIONS” section of this manual. WARNING – Hazards or unsafe practices which COULD result in severe personal injuray or death. DO NOT USE ALUMINUM FOIL TO LINE THE GRILL RACKS OR GRILL BOTTOM. This can severely upset combustion air flow or trap CAUTION excessive heat in th
Summary of the content on the page No. 4
PRECAUTIONS SAFETY INSTRUCTIONS WARNING: IMPORTANT! USING THE SIDE BURNER: Inspect the gas supply hose prior to turning the gas “ON”. If there is evidence of cuts, wear or abrasion, it must be replaced prior to use. Do not use the side burner if the odor of gas is present. WARNING: Always keep your face and body as far away from the burner as possible when lighting. WARNING: IMPORTANT! BEFORE LIGHTING… Inspect the gas supply hose prior to turning the gas “ON”. If there is e
Summary of the content on the page No. 5
SAFETY INSTRUCTIONS *** WARNING *** FOR YOUR SAFTY If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. Open lid 4. If odor continues, immediately call your gas supplier or your fire department. FOR YOUR SAFETY 1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appl
Summary of the content on the page No. 6
INSTALLATION OF SIDE SHELF SIDE SHELF ASSEMBLY • The screws used to attach the side shelf are already screwed into the right side panel (see the figure below). Remove the screws from the right side panel, align with the holes in the side shelf, and then re-screw into the holes on the right side panel of the grill. • Repeat the above step to install the left side shelf on left side panel. Please note: for the left side shelf, insert the top two screws from the inside of the grill a
Summary of the content on the page No. 7
PRECAUTIONS SAFETY INSTRUCTIONS When using the grill, do not touch the grill rack, burner grate or immediate surroundings as these Do not use the grill for cooking excessively fatty areas become extremely hot and could cause meats or products which promote flare-ups. Do not burns. Use only dry potholders. Moist or damp operate the grill under unprotected combustible potholders on hot surfaces may cause burns from construction. Use only in well ventilated areas. Do steam. Do not use a to
Summary of the content on the page No. 8
Summary of the content on the page No. 9
Summary of the content on the page No. 10
JENN-ALR NXRILL BATTERY & SPICE TRAY, INDIVIDUAL SHELF ASSEMBLY • In order to install the battery, remove the ignition button housing. Please keep the positive pole of the battery facing toward you. Insert the battery into the housing. Replace the ignition button housing after battery is installed. • The screws used to attach the spice tray are attached to the left door. Remove the two screws from the left door and align with the holes in spice tray and then re-screw into the holes on
Summary of the content on the page No. 11
CLOSE PROPANE TANK ASSEMBLY ● Attach propane gas tank to regulator inlet fitting by turning the regulator clockwise as shown in figure below. g 9 OPEN
Summary of the content on the page No. 12
GAS HOOK-UP Only the pressure regulator and hose assembly supplied with the grill should be used. Any LP Gas Cylinder must be fitted with Overfill replacement pressure regulator and hose assembly Protection Device (OPD). must be specified by the grill manufacturer. LP GAS HOOK-UP: This is a liquid propane configured grill. Ensure that the black plastic grommets on the LP cylinder valve are in place and that the hose does Do not attempt to use a natural gas supply unless not
Summary of the content on the page No. 13
LEAK TESTING GENERAL the burners. The flames of the burners should be Although all gas connections on the grill are leak visually checked. tested at the factory prior to shipment, a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment, or excessive pressure unknowingly being applied to the unit. Periodically check the whole system for leaks following the procedures listed below. If the smell of gas is detected at an
Summary of the content on the page No. 14
11 INSTALLER FINAL CHECK Specified clearance maintained 24” from Unit tested and free of leaks. combustibles. User informed of gas supply shut off valve All internal packaging removed. location. Knobs turn freely. Burners are tight and sitting properly on orifices. PLEASE RETAIN THESE INSTRUCTIONS FOR Pressure regulator connected and set for 11.2” FUTURE REFERENCE. W.C. LP gas. Gas connections to grill using hose & regulator assembly provided (pre-set for 11.0” w
Summary of the content on the page No. 15
OPERATING INSTRUCTION General use of the grill and rotisserie Each main burner is rated at 12,000 BTU/hr. The the stainless steel motor mount. The rotisserie main grill burners encompass the entire cooking motor must be electrically grounded in accordance area and are side ported to minimize blockage from with local codes or, in the absence of local codes, falling grease and debris. Above the burners are with the National Electrical Code, ANSI/NFPA 70- stainless steel radiant (flame tam
Summary of the content on the page No. 16
LIGHTING INSTRUCTIONS Burner flames should be blue and stable with no WARNING: IMPORTANT! yellow tips, excessive noise, or lifting. If any of these conditions exist call our customer service line. BEFORE LIGHTING… If the flame is yellow, it indicates insufficient air. If Inspect the gas supply hose prior to turning the gas the flame is noisy and tends to lift away from the “ON”. If there is evidence of cuts, wear, or abrasion, burner, it indicates too much air. it must be repl
Summary of the content on the page No. 17
TO MATCH LIGHT THE GRILL TO MATCH LIGHT THE GRILL: If the burner will not light after several attempts then the burner can be match lit. If you have already attempted to light the burner with the igniter, allow 5 minutes for any accumulated gas to dissipate. Keep your face and hands as far away from the grill as possible. Insert a lit extended match or lighter through the cooking grids to the burner. Press the control knob and rotate left to the HI setting, continue to press the knob
Summary of the content on the page No. 18
LIGHTING ILLUSTRATION Main & Side Burner Lighting Illustration Rotisserie Burner Lighting Illustration 1. Make sure the lid is in open position. 1. Push and turn the rotisserie knob to HI. 2. Push and turn one of main or side burner knob 2. Press the electric igniter 3 to 4 seconds to to HI position.
Summary of the content on the page No. 19
USING THE SIDE BURNER control knob counterclockwise to the “HI” position. If the burner does not light, turn the control knob to WARNING: IMPORTANT! “OFF”. If the smell of gas is detected and the igniter USING THE SIDE BURNER: is not functioning, immediately turn the control knob Inspect the gas supply hose prior to turning the gas “OFF”. Allow 5 minutes for any accumulated gas to “ON”. If there is evidence of cuts, wear or abrasion, dissipate. If the side burner igniter is not it
Summary of the content on the page No. 20
CARE & MAINTENANCE OF SIDE BURNER SIDE BURNER CLEANING: Clean the exterior of the burner with a wire brush. Clear any clogged burner ports with a straightened paper clip. Never enlarge the burner ports. Never use a wooden toothpick as it may break off and clog the port. STAINLESS STEEL: There are many different stainless steel cleaners available. Always use the mildest cleaning procedure first, scrubbing in the direction of the grain. Do not use steel wool, as it will scratch the s
