Summary of the content on the page No. 1
Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
Summary of the content on the page No. 2
IMPORTANT: PLEASE READ AND FOLLOW • Before beginning, please read these instructions EXCESSIVE WEIGHT HAZARD completely and carefully. Use two or more people to move and install this unit. • Do not remove permanently affixed labels, warnings, or Failure to follow this instruction can result in back or plates from product. This may void the warranty other injury. • Please observe all local and national codes and ordinances. • The installer should leave these instructions with the consumer who sho
Summary of the content on the page No. 3
BASIC SPECIFICATIONS T-SERIES GRILLS VG BQ30OT/O302T VGIQ300T VGBQ410T/VGIQ41 OT VGBQ412T Description Cutout Width 28 5/8" 28 5/8" 40 1/4" 40 1/4" (72.7 cm) (72.7 cm) (102.2cm) (102.2cm) 28" (71.1cm) Cutout Depth Cutout Height 101/4" (26.0cm) Overall Width 29 1/2" 29 1/2" 41 3/16" 41 3/16" (74.9cm) (74.9cm) (104.6cm) (104.6cm) 32 3/4" (83.2cm) Overall Depth Gas Natural: standard residential 1/2" (1.3 cm)ID gas service line. Requirements LP/Propane: equipped with high capacity hose/regulator asse
Summary of the content on the page No. 4
BASIC SPECIFICATIONS E-SERIES GRILLS VGBQ300E VGIQ300E VGBQ410ENGIQ410E VGBQ412E Description Cutout Width 28 5/8" 28 5/8" 40 1/4" 40 1/4" (72.7cm) (72.7cm) (102.2cm) (102.2cm) 28" (71.1cm) Cutout Depth 10 1/4" (26.0cm) Cutout Height Overall Width 29 1/2" 29 1/2" 41 3/16" 41 3/16" (74.9cm) (74.9cm) (104.6cm) (104.6cm) 32 3/4" (83.2cm) Overall Depth ,Sas Natural: standard residential 1/2" (1.3 cm) ID gas service line. Requirements LP/Propane: equipped with high capacity hose/regulator assembly for
Summary of the content on the page No. 5
GAS CONNECTION Verify the type of gas supply to be used, either natural or LP, and make sure the marking on the grill rating plate agrees with that of the supply. Never connect an unregulated gas line to the appliance. An installer supplied gas shut-off valve must be installed in an easily accessible location. All installer supplied parts must conform to local codes, or in the absence of local codes, with the National electrical Code, ANSI/NFPA 70 and the National Fuel Code, ANSI Z223.1. In Cana
Summary of the content on the page No. 6
NATURAL FIXED PIPING CONNECTION Connection: Standard Residential 1/2" ID gas service line - 1/2" NPT male with 7/8" (2.2 cm) flare adapter. 4.0" W.C.R Nat. Operating Pressure: Supply Pressure: 6" to 10" W.C.R Nat. If in excess of 10" W.C.R, a step-clown regulator is required. Check with your local gas utility company or with local codes for instructions on installing gas supply lines. Be sure to check on type and size of run and how deep to bury the lines. If the gas line is too small, the grill
Summary of the content on the page No. 7
LP/PROPANE FIXED PIPING CONNECTION Connection: Standard Residential 1/2" ID gas service line - 1/2" NPT male with 3/8" flare adapter. Operating Pressure: 10.0" W.C.R LP/Propane. Supply Pressure: 11" to 14" W.C.R Nat. If in excess of 14" W.C.R, a step-clown regulator is required. Check with your local gas utility company or with local codes for instructions on installing gas supply lines. Be sure to check on type and size of run and how deep to bury the lines. If the gas line is too small, the gr
Summary of the content on the page No. 8
LP/PROPAN E TAN K CON NECTION Outdoor grills orificed for use with LP/Propane gas come equipped with a high capacity hose/regulator assembly for connection to a standard 20 lb. LP/Propane cylinder equipped with a Type 1, QCC-1 connector. Hose assembly must comply with Elastomeric Composite Hose and Couplings for Conducting Propane and Natural Gas, CAN/CGA-8.1 standard or the Theromp/astic Hose and Hose Couplings for Conducting Propane and Natural Gas CAN 1-8.3 standard. (See LP/Propane tank requ
Summary of the content on the page No. 9
LEAK TESTING Although all gas connections on the grill are leak tested at the factory prior to shipment, a complete gas tightness check must be performed at the installation clue to possible mishandling in shipment or excessive pressure unknowingly being applied to the unit. Periodically check the whole system for leaks, or immediately check if the smell of gas is detected. 1. Do not smoke while leak testing. Extinguish all flames. 2. Never leak test with an open flame. 3. Make a soap solution o
Summary of the content on the page No. 10
INSTALLATION PROCEDURES FOR BUILT-IN INSTALLATION 1. A minimum of 6" (15.2 cm) from the sides, or a minimum of 8" (20.3 cm) from the right side if there is a rotisserie motor, and a minimum of 24" (61.0 cm) from the back must be maintained from the grill above the cookin9 surface to adjacent vertical combustible construction. The grill is not to be located under overhead unprotected combustible construction. 2. A minimum of 3" (7.6 cm) clearance from the back of the grill with a canopy and a min
Summary of the content on the page No. 11
,, ._ A ,. (15.2 cm) - 5 3/8" (13.7 cm) _ 8" (20.3 cm)* n 0 0 _° / o /, / o°@@0 / / / *Minimum / / / / clearance / / / needed for / removal and replacement of Rotisserie Motor. MODEL Dim. A VGBQ300T/0302T 29 1/2" (74.9 cm) VGBQ300E VGIQ300T 29 1/2" (74.9 cm) VGIQ300E VGBQ410T/VGIQ410T 41 3/16" (104.6 cm) VGBQ410E/VGIQ410E VGBQ412T 41 3/16" (104.6 cm) VGBQ412E VGBQ530T/VGIQ530T 53 3/16" (135.1 cm) VGBQ530E/VGIQ530E VGBQ532T/VGIQ532T 53 3/16" (135.1 cm) VGBQ532TNGIQ532T 11
Summary of the content on the page No. 12
CUTOUT DIMENSIONS Model Dim. B VGBQ300T/0302T 28 518" (72.7 cm) VGBQ300E VGIQ300T 28 5/8" (72.7 cm) VGIQ300E VGBQ410T/VGIQ410T 40 1/4" (102.2 cm) VGBQ410E/VGIQ410E VGBQ412T 40 1/4" (102.2 cm) VG BQ412E VGBQ530TNGIQ530T 52 1/4" (132.7 cm) VGBQ530E/VGIQ530E VGBQ532TNGIQ532T 52 1/4" (132.7 cm) VGBQ532E/VGIQ532E 28" (71.1 cm) Electrical Connection for **Gas Inlet and power cord Rotisserie Motor supply opening can be (position unit sothat the located anywhere within 5" plug is always accessible) (12.
Summary of the content on the page No. 13
BURNER ADJUSTMENT Each burner is tested and adjusted at the factory prior to shipment; however, variations in the local gas supply may make it necessary to adjust the burners. The flames of the burners (except the rotisserie infrared burner) should be visually checked and compared with Fig. 1, Fig. 2, and Fig. 3. Flames should be blue and stable with no yellow tips, excessive noise or lifting. If any of these conditions exist, check if the air shutter or burner ports are blocked by dirt, debris,
Summary of the content on the page No. 14
Fig. 3 SIDE BURNERS (If applicable) -1_ Air Shutters / °O _[ ° o I Orifice Fig. 4 FLAME HEIGHT SIDE BURNERS (If applicable) 3/8" (.95 cm) Fig. 5 FLAME HEIGHT INFRARED BURNER 1/4" (.64 cm) .-_ Fig. 6 FLAME HEIGHT TruSear BURN ER 1/4" (.64 cm) 14
Summary of the content on the page No. 15
ROTISSERIE SYSTEM The rotisserie motor is attached to the mounting bracket located on the right side of the grill frame. The ELECTRICAL SHOCK HAZARD rotisserie motor must be electrically grounded in accordance This appliance is equipped with a with local codes The skewer for the rotisserie is assembled into grounding plug for your protection against the gear box assembly by placing the pointed end into the gear shock hazard and should be plugged directly into a properly grounded box, and resting
Summary of the content on the page No. 16
F20054H (PSO606VR)
