Summary of the content on the page No. 1
Stainless Steel GAS GRILL
With Side Burner
USE AND CARE GUIDE
MODEL NO.: 720-0133-LP
®
FOR OUTDOOR USE ONLY
PLEASE CONTACT 1-800-913-8999 FOR ASSISTANCE
DO NOT RETURN TO PLACE OF PURCHASE.
Summary of the content on the page No. 2
MESSAGE TO OUR CONSUMERS Thank you for selecting our stainless steel gas grill. Because this appliance contains features which may not found on other grills, we recommend that you read this entire booklet before your first use. Keep it in a handy place as it has answers to questions that may occur during future use. Read this booklet carefully and be sure your gas grill is properly assembled, installed and maintained. Failure to follow these instructions could result in serious bodily injur
Summary of the content on the page No. 3
PRECAUTIONS CALIFORNIA PROPOSITION 65- FOR YOUR SAFETY WARNING If you smell gas: The burning of gas fuel generates some by- 1. Shut off gas to the appliance. products, which are on the list of substances, 2. Extinguish any open flames. which are known by the State of California to 3. Open lid. cause cancer or reproductive harm. California 4. If odor continues, immediately call law requires businesses to warn customers of your gas supplier. potential exposure to such substances. To minim
Summary of the content on the page No. 4
PRECAUTIONS DO NOT STORE ITEMS OF INTEREST TO Moist or damp potholders on hot surfaces may CHILDREN AROUND OR BELOW THE cause burns from steam. Do not use a towel or GRILL OR IN THE CART. NEVER ALLOW bulky cloth in place of potholders. Do not let CHILDREN TO CRAWL INSIDE OF THE potholders touch hot portions of the grill rack. CART. Grease is flammable. Let hot grease cool before Never let clothing, pot holders or other attempting to handle it. Avoid letting excess flammable materials come i
Summary of the content on the page No. 5
PRECAUTION Do not use the grill for cooking excessively This stainless steel grill is designed for fatty meats or products which promote flare- optimum performance without the use of ups. Do not operate the grill under unprotected briquettes. Do not place briquettes on the combustible construction. Use only in well radiant as this will block off the area for the ventilated areas. Do not use in buildings, grill burners to vent. Adding briquettes can garages, sheds, breezeways or other such d
Summary of the content on the page No. 6
SIDE SHELF ASSEMBLY STEP 1: Use two screws and lock washers to fasten the condiment tray to the side shelf ,use two screws and lock washers to fasten the support brackets to the side shelf as illustrated. STEP 2: Use two screws and lock washers to fasten the control panel to the side shelf, do not tighten these screws until the valve stem protrudes through the control panel(step 8);use two screws and lock washes to fasten the support brackets to the side burner as illustrated. 4
Summary of the content on the page No. 7
ASSEMBLY INSTRUCTION STEP 3: The screws used to attach the side shelves are already screwed into the side panel ( see the figure A below of the grill ).Remove the screws and flat washers from the both panels, also remove the 2 screws on the sides of both shelf assemblies(figure B). Figure A Figure B 5
Summary of the content on the page No. 8
ASSEMBLY INSTRUCTION STEP 4:Allow the side shelves washers & screws (removed to step 3 figure A) with the holes in the side panels of the grill, tighten each side shelf assembly into place, also tighten the screws taken from the shelf assemblies (step 3 figure B) back into each side shelf from inside the lid of the grill’s cooking area. 6
Summary of the content on the page No. 9
ASSEMBLY INSTRUCTIONS Step 5: Insert valve assembly through side Step 6: Remove 4(four) screws & washers panel from the “U” brackets on the side burner (Side panel, right) Step 7: Insert valve stem assembly into burner Step 8: Insert valve stem assembly into venturi face-plate. 7
Summary of the content on the page No. 10
ASSEMBLY INSTRUCTIONS Step 9: Replace “U” brackets with 4(four) Step 10: Align & start knob bezel & valve Screws( DO NOT TIGHTEN) Screws as shown below (DO NOT and stem with 2(two) screws & washers TIGHTEN) . ( Step 11; Tighten all 4(four) screws on the “U” Step 12: Place knob on v
Summary of the content on the page No. 11
ASSEMBLY INSTRUCTION STEP 13: The screws used to attach the push bar are already screwed into the sides of the push bar. Remove the screws from the push bar, align with the holes in the side shelf, and then re-screw into the holes on the push bar tightening it into place. Press the cap against the ends of the push bar, and gently tap them into place. 9
Summary of the content on the page No. 12
ASSEMBLY INSTRUCTION STEP 14: Place flame tamers, cooking grids, warming rack and grease tray as shown below. 10
Summary of the content on the page No. 13
ASSEMBLY INSTRUCTION STEP 15: The screws for rotisserie mount are already screwed into the rotisserie kit. Remove the screws and install. Assemble the rotisserie skewer as shown in the figure below. STEP 16: Install the battery in the battery casing , by unscrewing the battery cap located on the far left side of the control panel ,insert the battery (positive and pointing out) and replace the cap. 11
Summary of the content on the page No. 14
GAS HOOK-UP NEVER CONNECT AN UNREGULATED QCC1 in the standard for compressed gas GAS SUPPLY LINE TO THE APPLIANCE. cylinder valve outlet and inlet connection USE THE REGULATOR/HOSE ASSEMBLY ANSI/CGA-V-1. SUPPLIED. Manifold pressure: (operating): 10” water This is a liquid propane configured grill. Do column (W.C.), (non-operating): 11.2” water not attempt to use a natural gas supply unless column (W.C.). the grill has been reconfigured for natural gas L.P. GAS HOOK-UP use. Ensure that the b
Summary of the content on the page No. 15
CLOSE PROPANE TANK ASSEMBLE g Attach propane gas tank to regulator inlet fitting by turning the regulator clockwise as shown in figure below. LP gas cylinder must be fitted with a listed overfill prevention device (OPD) 13 OPEN
Summary of the content on the page No. 16
GAS HOOK-UP valve, hand tighten the nut clockwise to a To disconnect L.P. gas cylinder: complete stop. Do not use a wrench to 1. Turn the burner valves off. tighten. Use of a wrench may damage the quick coupling nut and result in a hazardous 2. Turn the tank valve off fully (turn condition. clockwise to stop). 6. Open the tank valve fully 3. Detach the regulator assembly from the (counterclockwise). Use a soapy water tank valve by turning the quick coupling solution to check all connections
Summary of the content on the page No. 17
LEAK TESTING GAS FLOW CHECK Check all gas supply fittings for leaks before each use. It is handy to keep a spray bottle of Each grill burner is tested and adjusted at the soapy water near the shut-off valve of the factory prior to shipment; however, variations gas supply line. Spray all the fittings. in the local gas supply may make it necessary Bubbles indicate leaks. to adjust the burners. The flames of the burners should be visually checked. Disconnected L.P. cylinders must have Flam
Summary of the content on the page No. 18
VISUAL CHECKING BURNER FLAME Approximate 1 1/2 “ Flame Height 16
Summary of the content on the page No. 19
OPERATING INSTRUCTIONS GENERAL USE OF THE GRILL the heat to a lower setting after the initial browning. This cooks the food through without Each main burner is rated at 12,000 Btu/hr. burning the outside. Foods cooked for a long The main grill burners encompass the entire time or foods basted with a sugary marinade cooking area and are side ported to minimize may need a lower heat setting near the end of blockage from falling grease and debris. the cooking time. Above the burners are st
Summary of the content on the page No. 20
GRILL LIGHTING INSTRUCTIONS FLAME CHARACTERISTICS and hands as far away from the grill as possible. Insert a lit match attached to tight lighting rod Check for proper burner flame characteristics. or lighter through the cooking Each burner is adjusted prior to shipment; however, variations in the local gas supply grids to the burner.(see next page) Press the may take minor adjustments necessary. control knob and rotate left to the HI setting, continue to press the knob until the burner Bu
