Summary of the content on the page No. 1
Use & Care Guide
Model: 90109
Kenmore®
Liquid Propane
Gas Grill
P/N 19000343A0 (1110)
Sears Canada Inc.
Toronto, ON., M5B 2C3
www.sears.ca
™
Summary of the content on the page No. 2
Table of Contents Precautions Warranty------------------------------------------------2 ! WARNING Safety Precautions--------------------------------2~4 Failure to comply with these instructions could Package Content List-----------------------------5~6 result in a fire or explosion that could cause Hardware Contents----------------------------------7 serious bodily injury, death, or property damage. Preparation--------------------------------------------7 Parts Diagram -----------------------
Summary of the content on the page No. 3
Precautions • Have your LP gas tank filled by a reputable propane gas dealer and visually inspected and re- qualified at each filling. A tank of approximately 12 inches in diameter by 18-1/2 • Do not store a spare LP gas tank under or inches high is the maximum size LP gas tank to use. • near this appliance. • Never fill the tank beyond 80 percent full . If this You must use an OPD gas tank which offers an information is not followed exactly a fire causing Overfill Prevention Device. dea
Summary of the content on the page No. 4
Burner Flame Check WARNING ! A strong gas smell, or the hissing sound of gas indicates a serious problem with your gas grill or the LP gas tank. Failure to immediately follow the steps listed below could result in a fire or explosion that could cause serious bodily injury, death, or property damage. • Shut off gas supply to the gas grill. • Turn the control knobs to OFF position. • Put out any flame with a proper fire extinguisher. • Open Grill Lid. • Get away from the LP gas tank. Visually
Summary of the content on the page No. 5
200 300 10 5 400 250500 600 15000 50 350 7 00 FC PACKAGE CONTENTS LIST A. Firebox--------1pc. B. Bottom panel----1pc. C. Tank Tray Bolt---1pc. D. Swivel Caster with Brake---1pc. E. Swivel Caster---------1pc. F. Caster----------2pcs. G. Side Panel, Left-----1pc. H. Side Panel, Right-----1pc. I. Back panel----1pc. J. Gas Tank Barrier Bar---1pc. K. Door handle-----2pcs. L. Door, Left------1pc. M. Door Right-----1pc. N. Side Burner bowl assembly frame O. Left side shelf with side with Side burner
Summary of the content on the page No. 6
T. Bezel---------------------------1 pc U.. Control Knob-------------1 pc V.1.5 Volt “AA” Size Alkaline Battery----------1pc. W. Grease Tray -----1pc. X. Grease Cup----------------1pc Y. Manual Lighting Stick-----1pc. 6
Summary of the content on the page No. 7
Hardware Pack Contents Item Description Specification Quantity Phillips Head Screw AA 1/4 x 15mm 16 pcs Phillips Head Screw BB 1/4 x 10mm 14 pcs Phillips Head Screw CC 5/32 x 8mm 15pcs Flat Head Screw DD 5/32 x 8mm 8 pcs Flat Washer EE 1/4 4pcs Lock Washer FF 1/4 26pcs Lock Washer GG 5/32 11 pcs Hex Wrench HH 5/64 1pc Preparation Before beginning assembly, make sure all parts are present. Compare parts with package contents list and diagram above. If any part is missing or damaged, do not atte
Summary of the content on the page No. 8
Model 90109 Parts diagram 0 2 0 1 0 3 0 4 0 5 5 7 0 6 0 2 5 6 0 7 0 6 0 6 5 3 5 5 5 2 5 1 5 4 0 8 5 0 0 6 4 9 1 0 1 1 4 8 1 6 1 7 4 6 1 8 12 0 9 1 3 1 4 4 5 1 5 3 7 5 8 4 7 1 9 4 4 4 3 2 0 4 1 4 2 4 0 2 3 3 9 3 8 2 1 2 6 2 5 2 8 2 2 3 0 2 9 2 4 3 1 2 7 2 7 3 3 3 0 3 0 3 6 3 5 3 3 3 4 3 2 3 0 8
Summary of the content on the page No. 9
Model 90109 Parts List QUANTIT KEY# PARTS DESCRIPTION QUANTITY KEY# PARTS DESCRIPTION Y 1 0773-001 Main Lid 1 30 0773-030 Door Hinge 4 2 0773-002 Main Lid Screw 2 31 0773-031 Front Door, Left 1 3 0773-003 Temperature Gauge Housing 1 32 0773-032 Front Door, Right 1 4 0773-004 Temperature Gauge 1 33 0773-033 Door Handle 2 5 0773-005 Logo 1 34 0773-034 Lighting Rod 1 6 0773-006 Hood Buffer 4 35 0773-035 Lighting Rod Cover 1 7 0773-007 Main Lid Handle 1 36 0773-036 Gas Tank Barrier Bar 1 8 0773-00
Summary of the content on the page No. 10
Fig. 1 Assembly Instructions D B CAUTION: While it is possible for one person to assemble this grill, obtain assistance from another E person when handling some of the larger, heavier F pieces. Note: Be sure to slide grease tray out of back of grill head and remove all packaging from tray. F 1. Use the parts list to check that all parts have been included. 2. Inspect the grill for damage as you assemble it. Do not Fig. 2 assemble or operate the grill if it appears damaged. If there are da
Summary of the content on the page No. 11
C 400 100200 53000150 250530050 600700 50F 400 50 0 200 30015 0 250350 6 00 5100F0 50 700 C (e) Attach door handle (K) to left door (L) using (2) 5/32 x Fig. 5 8mm Phillips head screws (CC) and (2) 5/32 lock washers (GG). Repeat to assemble the other door handle to right door (M). (Fig.5) (f) Attach two doors (L & M) to side panels (G & H) using (8) 5/32 x 8mm flat head screws (DD). (Fig. 6) 2. Firebox Assembly L M K (a) Be sure grill cart doors are closed to stabilize cart. Remove grill h
Summary of the content on the page No. 12
F 150 400 250500 600 C50 350 70 0 300 4 00 500 200 150 250 600 15000 C 50 350 700 200 300 15000 F 3. Side Burner & Side Shelf Assembly Fig.9 A (a) Loosen (2) preinstalled 1/4 x 10mm Phillips head screws and (2) ¼ lock washers from right side of grill head (A) as shown. Do not screw out fully; leave ¼ extended for shelf assembly. (Fig. 9) (b) Through side burner shelf keyholes, hang side burner shelf (N) on two loosened screws. (Fig. 10) (c) Using (2) 1/4 x 10mm Phillips head screws (BB) an
Summary of the content on the page No. 13
4. Side Burner Valve Assembly Fig. 12 N (a) Remove side burner grate from side burner shelf and set aside. Remove the two Phillips head screws attaching side burner (N) to shelf to make room to install side burner valve. See (Fig.12) (b) Remove two screws from side burner control valve face. Insert side burner valve control stem through hole in side burner control panel . Place side burner control knob bezel (T) over side burner valve control stem. Secure bezel to control panel and valve
Summary of the content on the page No. 14
400 5 200 35000 150 250 3000 6 00 51000F C 5 700 5. Grease Cup Assembly Fig.16 From the back, pull out grease tray (W), remove any packaging materials from it, then insert grease cup (X) into grease tray (W) as shown in (Fig.16). Push grease tray back into grill. 6. Installing Cooking Components (a) Place heat diffusers over burners as shown. Diffuser ends insert into channels on front and back of firebox. w X (Fig. 17) (b) Evenly space cooking grates (R) on the ledge above heat diffusers.
Summary of the content on the page No. 15
200153000400 250500 60 0 15F 00050 C 350 700 8. Connecting LP Gas Tank to LP Grill Fig.19 (a) From front of the cart, place foot ring of 20 lb tank into C the hole in bottom panel. Make sure the tank valve is in OFF position. Use the tank bolt to secure the tank in a fixed position (Fig.19). (b) Check the tank valve to ensure it has proper external mating threads to fit the hose and pressure regulator assembly provided. (c) Make sure all burner valves are in OFF position. (d) Inspect the v
Summary of the content on the page No. 16
3. Be sure all gas connections are securely Checking for LP gas leaks tightened. 4. Turn on gas supply. Never test for leaks with a flame. Prior to first use, at 5. Open the grill main lid. the beginning of each season, or every time your LP 6. Push and turn any main burner control knob to gas tank is changed, you must check for gas leaks. HI position. Push Electronic Ignition button for 3 to 5 seconds to light burner. 1. Make a 50/50 (soap/water) mild soap solution. 2. Turn the contro
Summary of the content on the page No. 17
! WARNING If Grill Still Fails To Light Never lean over the grill cooking area while 1. Check gas supply and connections for leaks. Check lighting your gas grill. Keep your face and body that all wire connections are secure. a safe distance (at least 18 inches) from the cooking grid surface when lighting your grill by 2. Repeat basic lighting procedure. If your grill still match. fails to operate, turn the gas off at source, turn the control knobs to OFF, then check the following: Manuall
Summary of the content on the page No. 18
Cleaning Exterior Stainless Steel Surfaces Cleaning and Maintenance Weathering and extreme heat can cause exterior stainless steel surfaces to turn tan in color. Machine oils used in manufacturing process of stainless steel can also To ensure a proper working unit the following proper cause this tanning color. Use a stainless steel cleaner to care and maintenance is suggested. polish stainless steel surfaces of your grill. Never use abrasive cleaners or scrubbers because they will scratch
Summary of the content on the page No. 19
! WARNING 2. Clean any clogged ports with a stiff wire, such as The location of the burner tube with respect to the an open paper clip. orifice is vital for safe operation. Check to ensure the 3. Inspect each burner for damage (cracks or holes) orifice is inside the burner tube before using the gas and if such damage is found, order and install a new grill. If the burner tube does not fit over the valve burner. After installation check to ensure that gas orifice, lighting the burner may
Summary of the content on the page No. 20
Cooking Instructions Indirect Cooking To cook indirectly, the food should be placed on the left or right side of your grill with the burner lit WARNING ! on the opposite side. Do not leave the grill unattended. Your grill will get very hot. Never lean over Flare-ups the cooking area while using your grill. Do not The fats and juices dripping from grilled food can touch cooking surfaces, grill housing. Grill Lid cause flare-ups. Since flare-ups impart a or any other grill parts while the
