Summary of the content on the page No. 1
Use & Care Guide
Manual de Uso y Cuidado
English / Español
Model/Modelo: 146.16142210
Item / Artículo: 640-03982839-7
Kenmore®
Liquid Propane Gas Grill
Parilla a gas de propane liquido
P/N 40900319
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
www.kmart.com
™
Summary of the content on the page No. 2
Installation Safety Precautions • Please read this User’s Manual in its entirety before using DANGER the grill. • Failure to follow the provided instruction can result in If you smell gas: seriously bodily injury and/or property damage. • Some parts of this grill may have sharp edges. Please wear suitable protective gloves. 1. Shut off gas to the appliance. • Use grill, as purchased, only with LP (propane) gas and the 2. Extinguish any open flame. regulator/valve assembly supplied. •
Summary of the content on the page No. 3
TABLE OF CONTENTS WARRANTY KENMORE GRILL WARRANTY . . 2 For Your Safety . . . . . 2 Grill Service Center. . . One Year Full Warranty on Kenmore Grill . 2 Product Record Information . . . If this grill fails due to a defect in material or workmanship . . 2 Installation Safety Precautions . . . within one year from the date of purchase, call 1-800-4-MY ® HOME to arrange for free repair (or replacement if repair . . 2 Safety Symbols . . . proves impossible). . 3 Kenmore Grill Warranty . . . L
Summary of the content on the page No. 4
LP Cylinder USE AND CARE • The LP cylinder used with your grill must meet the following requirements: • Use LP cylinders only with these required measurements: 12" DANGER (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) Capacity maximum. • NEVER store a spare LP cylinder under or near the • LP cylinders must be constructed and marked in accordance appliance or in an enclosed area. with specifications for LP cylinders of the U.S. Department of Transportation (DOT) or for C
Summary of the content on the page No. 5
LP Tank Exchange Connecting Regulator To The LP Tank • Many retailers that sell grills offer you the option of replacing 1. LP tank must be properly secured onto grill. (Refer to your empty LP tank through an exchange service. Use only those assembly section.) reputable exchange companies that inspect, precision fill, test 2. Turn all control knobs to the OFF position. and certify their cylinders. E Exchange your tank only for an OPD 3. Turn LP tank OFF by turning OPD hand wheel clockwise
Summary of the content on the page No. 6
Leak Testing Valves, Hose and Regulator 1.T Turn all grill control knobs to OFF. 2.Be sure regulator is tightly connected to LP tank. 3.Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. C Correct before proceeding by calling Sears for replacement parts at ® 1-800-4-MY-HOME . Hold coupling nut and regulator 4.Brush soapy solution onto areas where bubbles are shown in as sho
Summary of the content on the page No. 7
Safety Tips Before opening LP cylinder valve, check the coupling nut for WARNING tightness. When grill is not in use, turn off all control knobs and LP cylinder For Safe Use of Your Grill and to Avoid Serious valve. Injury: Never move grill while in operation or still hot. • Do not let children operate or play near grill. Use long-handled barbecue utensils and oven mitts to avoid burns • Keep grill area clear and free from materials that and splatters. burn. Maximum load for side
Summary of the content on the page No. 8
Burner Flame Check • Remove cooking grates and heat diffusers. Light burners, turn WARNING knobs from HI to LO. You should see a smaller flame in LO position than seen on HI. Perform burner flame check Turn controls and gas source or tank OFF when not on sideburner, also. Always check flame prior to each use. If in use. only low flame is seen refer to "Sudden flame drop or low flame" in the Troubleshooting Section. HI HIGH CAUTION LO LOW If ignition does not occur in 5 seconds, turn the
Summary of the content on the page No. 9
Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burner CAUTION WARNING assembly or if you have trouble igniting grill. 1. Turn gas off at control knobs and LP cylinder. 2. Remove cooking grates and heat diffusers. SPIDER ALERT! SPIDER ALERT! 3. Remove cotter pin from rear of burners. SPIDER ALERT! 4. Carefully lift each burner up and away from valve openings. IMPORTANT: Always ensure that the venturi burner tubes . are clean. A venturi burner
Summary of the content on the page No. 10
Indirect Cooking Food Safety Poultry and large cuts of meat cook slowly to perfection on the grill Food safety is a very important part of enjoying the outdoor by indirect heat. Place food over unlit burner(s); the heat from lit cooking experience. To keep food safe from harmful bacteria, burners circulates gently throughout the grill, cooking meat or follow these four basic steps: poultry without the touch of a direct flame. This method greatly Clean: Wash hands, utensils, and surfa
Summary of the content on the page No. 11
Key Description Qty Part Number Key Description Qty Part Number Key Description Qty Part Number Key Description Qty Part Number 1S Side Burner Lid 1 40200044 30 CCotter Pin 8 110050 1S Side Burner Lid 1 40200044 31 CCotter Pin 8 110050 2R Rotate Rod, Side Burner Lid 2 40800118 31 C Cart Support Angle Bar 2 40900060 2R Rotate Rod, Side Burner Lid 2 40800118 32 CCart Support Angle Bar 2 4090
Summary of the content on the page No. 12
S DIAGRAM 12 • 16142-40900319
Summary of the content on the page No. 13
BEFORE ASSEMBLY READ AND FOLLOW THE INSTRUCTIONS BELOW TO CORRECTLY UNPACK GRILL PARTS FROM SHIPPING BOX. Step 1: Open shipping box by slicing down its edges with a box cutter, take out hardware pack, manual, bottom shelf, two doors. Next remove the two side panels, warming rack, door bracket, back rail and back panel. Remove all parts from plastic bags. 16142-40900319 • 13
Summary of the content on the page No. 14
BEFORE ASSEMBLY Step 2: Remove the left and right Styrofoam from Grill Head. Open grill lid and take out the boxes, packaged grates and grease tray. Remove all packing material, and take all parts out of boxes. 14 • 16142-40900319
Summary of the content on the page No. 15
BEFORE ASSEMBLY 16142-40900319 • 15
Summary of the content on the page No. 16
ASSEMBLY CAREFULLY READ AND PERFORM ALL ASSEMBLY INSTRUCTIONS ON THE FOLLOWING PAGES. Tools Required: Adjustable wrench (not provided) Screwdriver (not provided) 7/16” Combination wrench (not provided) The following hardware is provided in blister pack for convenient use. M4X10 screw M4X10 countersunk head screw AAA Battery Qty: 28 pcs Qty: 8 pcs Qty: 1 pc M5X10 screw M5 flat washer Qty: 4 pcs Qty: 4 pcs M6X13 screw M6 compression washer Qty: 32 pcs Qty: 8 pcs 16 • 16142-40900
Summary of the content on the page No. 17
Bottom Shelf Turn bottom shelf upside down. Attach the casters to bottom shelf with ( (16) M6x13 screws. Note: Install each caster into the correct position as shown in the figure below. The standard 1 2 caster will only install in one direction. Turn bottom shelf right side up. Attach door magnets to bottom shelf with ( (2) M4x10 screws. M6X13 screw Qty: 16 pcs M4X10 screw Qty: 2 pcs Swivel Caster Standard Caster Key#: 28 Key#: 27 Part#: 40900213 Part#: 40900214 Swivel Caster w
Summary of the content on the page No. 18
Cart To attach side panels, align side panel leg holes with leg holes on each side of bottom shelf. Left side panel has match holder attachment. Attach left and right side panels to sides of bottom shelf with ( (4) M6x13 screws. (A) Attach back panel to bottom shelf and two side panels with ( (6) M4x10 screws. (B) Attach tank baffle bar to back panel and bottom shelf with ( (2) M4x10 screws. (C) Align door bracket holes with holes on side panels. Attach bracket to side panels with ( (4
Summary of the content on the page No. 19
Front Doors Remove the (4) M5x15 screws pre-assembled to the door handle ends, and use them to attach handles to doors. Place the door in front of cart, align door hinge holes with holes on side of door, and attach the door to the door hinges with (4) M4x10 countersunk head screws. Do not fully tighten at this time. Repeat this for the other door. Close the doors to adjust them to line up as necessary, and fully tighten screws. M4x10 countersunk head screws Qty: 4pcs 16142-40900319
Summary of the content on the page No. 20
Grill Head to Cart This step requires two people to lift and position grill head onto cart. Remove the tie wraps securing regulator hose to underside of grill head. Pull hose and igniter wires out to side of grill head. Carefully lower the grill head onto the cart. Make sure the regulator hose and igniter wires are hanging outside the cart. Open lid and attach head to cart with ( (4) M6x13 screws and M6 compression washers. Align back rail holes with holes on side panels and firebox. At
