Summary of the content on the page No. 1
Use & Care Guide
Model: 415.16151110
® ® ®
P/N G550-001-020801
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www,sears,com
Model 464220311 ° Sept02-10
Summary of the content on the page No. 2
CALIFORNIA PROPOSITION 65 If you smell gas: 1. Combustion by-products produced when using this |. Shut off gas to the appliance. product contain chemicals known to the State of 2. Extinguish any open flame. California to cause cancer, birth defects, and other reproductive harm. 3. Open lld. 2. This product contains chemicals, including lead 4. If odor continues, keep away from the appliance and lead compounds, known to the State of and immediately call your gas supplier or your California to cau
Summary of the content on the page No. 3
For Your Safety ...................................... 2 KENMORE GRILL WARRANTY Grill Information Center .............................. 2 ProductRecord Information...........................2 One Year Full Warranty on Kenmore Grill SafetySymbols ...................................... 2 If this grill fails due to a defect in material or workmanship within one year from the date of purchase, Installation Safety Precautions.........................2 call 1-800-4-MY-HOME ®to arrange for free repair
Summary of the content on the page No. 4
LP Tank * The LP Tank used with your grill must meet the following requirements: * Use LP Tanks only with these required measurements: 12" / x, II _/ (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. • NEVER store a spare LP cylinder under or near the * LP Tanks must be constructed and marked in accordance appliance or in an enclosed area. with specifications for LP Tanks of the U.S. Department of Transportation (DOT) or for Canada, CAN/CSA-B339, tanks, spheres and
Summary of the content on the page No. 5
LP Tank Exchange Connecting Regulator To The LP Tank * Many retailers that sell grills offer you the option of l. LP tank must be properly secured onto grill. (Refer to replacing your empty LP tank through an exchange service. assembly section.) Use only those reputable exchange companies that inspect, precision fill, test and certify their tanks. Exchange your 2. Turn all control knobs to the OFF position. tank only for an OPD safety feature-equlpped tank as 3. Turn LP tank OFF by turning OPD h
Summary of the content on the page No. 6
Leak Testing Valves, Hose and Regulator 1. Turn all grill control knobs to OFF. 2. Be sure regulator is tightly connected to LP tank. 3. Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding by calling Sears for replacement parts at 1-800-4-MY-HOME ®. Hold coupllng nut and regulator 4. Brush soapy solution onto areas where bubbles are shown in as shown for
Summary of the content on the page No. 7
Safety Tips A Before opening LP cylinder valve, check the coupling nut for tightness. A When grill is not in use, turn off all control knobs and LP cylinder valve. For Safe Use of Your Grill and to Avoid Serious A Never move grill while in operation or still hot. Injury: A Use long-handled barbecue utensils and oven mitts to • Do not let children operate or play near grill. avoid burns and splatters. A Maximum load for sideburner and side shelf is 10 Ibs. • Keep grill area clear and free from ma
Summary of the content on the page No. 8
Burner Flarne Check " Remove cooking grates and flame tamers. Light burners, rotate knobs from Hi to LOW. You should see a smaller flame in LOW position than seen on Hi. Perform burner Turn controls and gas source or tank OFF when not flame check on sideburner, also. Always check flame prior In use. to each use. If only low flame is seen refer to "Sudden drop or low flame" in the Troubleshooting Section. --Hi if ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes a
Summary of the content on the page No. 9
3. Remove carryover tubes and burners. 4. Detach electrode from burner. CAUTION NOTE: Removal/Detachment method will depend on the burner configuration. See different configurations in f illustrations below. SPIDER ALERT! 5. Carefully lift each burner up and away from valve openings. We suggest three ways to clean the burner tubes. Use the one easiest for you. (A) Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run the hook through each burner tube several times. (g)
Summary of the content on the page No. 10
Indirect Cooking Food Safety Poultry and large cuts of meat cook slowly to perfection on Food safety is a very important part of enjoying the the grill by indirect heat. Place food over unlit burner(s); the outdoor cooking experience. To keep food safe from heat from lit burners circulates gently throughout the grill, harmful bacteria, follow these four basic steps: cooking meat or poultry without the touch of a direct flame. Clean: Wash hands, utensils, and surfaces with hot soapy This method g
Summary of the content on the page No. 11
I I Key Qty Description Part# Key Qty Description Part# 1 1 LEFT LEG ASSEMBLY G550-1300-W1 37 1 CLIP F/ SIDEBURNER G405-OO19-W1 2 1 MATCH HOLDER G401-OO79-W1 38 1 SIDEBURNER GRID G430-0053-W1 3 1 RIGHT LEG ASSEMBLY G550-1400-W1 39 1 SHIELD, HEAT, FIREBOX G550-5104-W1 4 1 BOTTOM SHELF G550-0800-W1 40 4 HEAT DIFFUSER G550-OOO6-W1 5 1 FRONT PANEL G550-O900-W2 41 3 COOKING GRATE G550-0012-W1 6 2 TANK EXCLUSION WIRE G550-0004-W1 42 1 SWING AWAY GRATE G550-0011-W1 7 1 AXLE ROD G550-0009-W1 43 1 BUTTON
Summary of the content on the page No. 12
® _ii ¸_i!i_!i © 12 o 464220311
Summary of the content on the page No. 13
CAUTION: When unpacking grill components, two people should raise grill head from the shipping box. Bottom Shelf to Legs [] Place bottom shelf end with cut out hole for LP cylinder between leg assembly with axle holes. E1 Attach to right and left leg assemblies with (4) 1/4-20x1-1/2" screws and (4) 1/4-20 flange nuts. [] Tighten securely. 1/4-20 Flange nuts Qty. 4 Match Holder 1/4-20x1-1/2" Screws Qty. 4 Left Leg Assembly Right Leg Assembly Bottom Shelt NOTE: One side panel image has been remove
Summary of the content on the page No. 14
[] Attach front panel to grill cart with (6) #8-32x3/8" sheet metal screws. Make sure metal tabs for B Front Panel tank exclusion wires are toward the bottom of cart. #8-32x3/8" sheet metal screws Qty. 6 Tank Exclusion Wire [] Hang tank exclusion wire onto front panel brackets; attach other ends to bottom shelf with (2) #8-32x3/8" sheet metal screws. #8-32x3/8" sheet metal screws Qty. 2 14 o 464220311
Summary of the content on the page No. 15
Wheels and Leg Extenders to Cart [] Turn cart assembly upside down. [] Insert axle rod through wheel, wheel spacer, legs and other wheel. Be sure to face "cone" side of wheel against leg. Attach with (t) axle washer and hitch pin. [] Hammer leg extenders into right legs. Leg Extenders Wheel Spacer Hitch Pin Qty. 1 Axle Washer Qty. 1 Qty. 1 Wheel Axle Rod Axle Washer / Wheel Spacer \ Hitch Pin "Cone" side of wheel against leg 464220311 " 15
Summary of the content on the page No. 16
Grill Head to Cart [] Stand cart upright. [] This step requires two people to lift and position grill head onto cart. [] Carefully lower the grill head onto the cart. Make sure the regulator hose is hanging outside the cart. Attach head to cart with (4) 1/4-20xl/2" screws. 1/4-20xl/2" screws Qty. 4 Grill Head Y 16 - 464220311
Summary of the content on the page No. 17
Right Side Shelf [] Attach towel bar to right side shelf with (2) A Towel Bar #10-24x3/8" screws, 5mm lock washers and / 5ram flat washers (A). [] Hook side walt of shelf over support brackets on side of firebox (B). [] Insert (4) 7ram fiber washers and (4) t/4-20xl/2" screws through inside front of firebox and through outside back of firebox as shown (C). [] Attach shelf with (4) 1/4-20 flange nuts (D). Support Bracket #10-24x3/8" Rig;Side Shelf screwSQty. 2 1/4-20xl/2" 7mm 1/4-20 5mm screws Fi
Summary of the content on the page No. 18
Side Burner Shelf [] Hook side wall of side burner shelf over support brackets on side of firebox (A). [] Inside firebox insert (4) fiber washers and (4) 1/4-20xl/2" screws as shown (B). [] Attach shelf using (4) 1/4-20 flange nuts (C). 1/4-20xl/2" screws Qty. 4 Lid removed for clarity Side Burner Shelf / 7mm Fiber Washers Qty. 4 1/4-20 Flange Nuts Qty. 4 Left Fascia [] Attach fascia to firebox with (3) #8-32x3/8" sheet metal screws. CAUTION: Fascia must be securely tightened to firebox to safel
Summary of the content on the page No. 19
Sideburner Valve, $ideburner Sideburner Bezel, Ignitor Wire, Control Knob [] Position valve behind fascia and line up holes (A). [] Insert (1) of the #8-32x3/8" stainless steel screws, but do not fully tighten. [] Slip bezel under inserted screw and position as shown (A). [] Line up other hole and insert (1) #8-32x3/8" stainless steel screw through bezel and into valve. [] Tighten both securely. [] Place sideburner into shelf (B). Make sure to insert valve into sideburner tube. Attach sideburner
Summary of the content on the page No. 20
[] Attach heat shield over burners inside front of grill with (2) #8-32x3/8" sheet metal screws. Heat Shield Heat Shield #8-32x3/8" / sheet metal screws Qty. 2 Lid removed for clarity ;ril! Front 20 o 464220311
