Summary of the content on the page No. 1
Use & Care Guide
Manual de Uso y Cuidado
English / Espafiol
Models/Modelos: 146.16132110/146.16133110
I(enmore
@ @ @
??ril
g _ prop_ I°
P/N 40200104
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
Summary of the content on the page No. 2
Installation Safety Precautions • Please read this User's Manual in its entirety before using the grill. • Failure to follow the provided instruction can result in If you smell gas: seriously bodily injury and/or property damage. • Some parts of this grill may have sharp edges. Please wear suitable protective gloves. 1. Shut off gas to the appliance. • Use grill, as purchased, only with LP (propane) gas and the 2. Extinguish any open flame. regulator/valve assembly supplied. • Grill installation
Summary of the content on the page No. 3
2 For Your Safety ... KENMORE GRILL WARRANTY 2 Grill Service Center... One Year Full Warranty on Kenmore Grill 2 Product Record Information ... 2 Installation Safety Precautions ... If this grill fails due to a defect in materiai or workmanship within one year from the date of purchase, catI 1-800-4-MY 2 Safety Symbols ... HOME @ to arrange for free repair (or replacement if repair 3 proves impossible). Kenmore Grill Warranty... •.. 4-10 Use and Care. Limited Warranty on Burners ...11 Parts List
Summary of the content on the page No. 4
LP Cylinder • The LPcylinder used with your grill must meet the following requirements: • Use LPcylinders only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7 cm) (tail) with 20 lb. (9 kg.) Capacity maximum. ° NEVER store a spare LP cylinder under or near the • LPcylinders must be constructed and marked in accordance appliance or in an enclosed area. with specifications for LPcylinders of the U.S. Department of Transportation (DOT) or for Canada, CAN/CSA-B339, cylinders, sp
Summary of the content on the page No. 5
LP Tank Exchange Connecting Regulator To The LP Tank • Many retailers that seii griiis offer you the option of replacing 1. LPtank must be properly secured onto grill. (Refer to your empty LPtank through an exchange service. Use only those assembly section.) reputable exchange companies that inspect, precision fill, test 2. Turn aII control knobs to the OFF position. and certify their cylinders. Exchange your tank only for an OPD 3. Turn LPtank OFF by turning OPD hand wheel clockwise to a safety
Summary of the content on the page No. 6
Leak Testing Valves, Hose and Regulator 1.Turnall grill control knobsto OFF. 2.Be sure regulator is tightly connected to LPtank. 3.Compieteiy open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major Ieak at the connection. Correct before proceeding by calling Sears for replacement parts at 1-800-4-MY-HOME _. Hold coupling nut and regulator 4.Brush soapy solution onto areas where bubbles are shown in as shown for proper
Summary of the content on the page No. 7
Safety Tips • Before opening LPcylinder valve, check the coupling nut for tightness. • When grill is not in use,turn off all control knobs and LP cylinder For Safe Use of Your Grill and to Avoid Serious valve. Injury. • Never move grill while in operation or stili hot. • Do not let children operate or play near grill. • Use long-handled barbecue utensils and oven mitts to avoid burns • Keep grill area clear and free from materials that and splatters. burn. • Maximum load for sideburner and side
Summary of the content on the page No. 8
Burner Flame Check • Removecooking grates and flame tamers. Lightburners,rotate knobsfrom HIGH to LOW. You shouldsee a smaller flame in LOW position than seen on HIGH. Performburner flame check Turn controls and gas source or tank OFF when not on sideburner,also.Always check flame prior to each use.If in use. only tow flame is seen refer to "Suddendrop or Iow flame" in the Troubleshooting_Section. HIGH CAUTION LOW If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minu
Summary of the content on the page No. 9
Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burner assembiy or if you have froubie igniting griii. 1. Turn gas off at control knobs and LPcylinder 2. Remove cooking grates and heat diffusers. SPIDER ALERT! 3. Remove screws and carryover tubes from rear of burners. 4. Remove screw and washers to disengage burner from IMPORTANT: Always ensure that the venturi burner tubes b.rackef on firebox. are clean. A venturi burner tube has a narrow area in 5. Remov
Summary of the content on the page No. 10
Indirect Cooking Food Safety Poultry and large cuts of meat cook slowly to perfection on the grill Food safety is a very important part of enjoying the outdoor by indirect heat. Place food over unlit burner(s); the heat from tit cooking experience. To keep food safe from harmful bacteria, burners circulates gently throughout the grill, cooking meat or foilow these four basic steps: poultry without the touch of a direct flame. This method greatly Clean: Wash hands, utensils, and surfaces with hot
Summary of the content on the page No. 11
Key Qty Part Number 1 Sideburner Lid 1 40200044 36 Mater Holder Bracket 1 40800129 2 Rotate Rod, Sideburner Lid 2 40800118 37 Back Panel 1 40200052 3 Sideburner Grid 1 40800119 38 Door Bracket 1 40200055 4 Sideburner 1 40800120 39 Right Door PinBracket 1 40200057 5 1 40800121 40 Left Door Pin Bracket 1 40200056 Ignitor Wire, Sideburner 6 Sideburner Base 1 40800063 41 Top Door Magnet 1 40200094 7 1 40200035 42 Back Rail 1 40200053 Right Side Shelf 8 1 40200039 Fascia, RightSide Shelf 43 Grease Cu
Summary of the content on the page No. 12
___ .................................................................................. / \ \ \ 12 _ 1613_.4200104
Summary of the content on the page No. 13
READ AND FOLLOW THE INSTRUCTIONS BELOW TO CORRECTLY UNPACK GRILL PARTS FROM SHIPPING BOX. Step 1: Once you open the top of the shipping box, slice down its four edges with a box cutter. Take out the Hardware Pack, two grill side panels, back panel and bottom shelf. Next remove the door bracket, back rail and warming rack. Take the left and right doors out of protective styrofoam, but leave grill head in styrofoam until Step 2. Remove all parts from plastic bags. 16132-40200104 * 13
Summary of the content on the page No. 14
Step 2. With the aid of an assistant, turn grill head over on its side as shown in the first figure below, and remove the top styrofoam piece. Lay the styrofoam piece flat on the floor. With the aid of an assistant, lift the grill head out of the bottom styrofoam piece. Place the grill upright on the other styrofoam piece as shown in the second figure below. CAUTION. DO NOT place the grill head directly on the floor or the grease tray could become bent. 14 * 16132-40200104
Summary of the content on the page No. 15
Step 3. Open grill lid, and take out the small boxes packed within the grill head. Remove all packing materials, and remove all parts from boxes as shown in the figures below. if!if: _ t / 16132-40200104 * 15
Summary of the content on the page No. 16
CAREFULLY READ AND PERFORM ALL ASSEMBLY iNSTRUCTiONS ON THE FOLLOWING PAGES. Tools Required: • Adjustable wrench (not provided) • Screwdriver (not provided) • 7/16" Combination wrench (not provided) • The following hardware is provided in a blister pack for convenient use. M4XIO screw Qty: 20 pcs M5XIO screw M5 flat washer M5 lock washer Qty: 4 pcs Qty: 4 pcs Qty: 4 pcs M6X13 screw M6X15 screw M6 flat washer(Dia 16) Qty: 16pcs Qty: 16pcs Qty: 8 pcs @ M6 lock washer M6 flat washer(Dia 12) M6 comp
Summary of the content on the page No. 17
MBX15 screw QW: i6 pcs M6 lock washer M4XIO screw Qt¥:2 pcs 16132-4020010
Summary of the content on the page No. 18
Cart [] To attach side panels, align side panel leg holes with leg holes on each side of bottom shelf. Left side panel has match holder attachment. [] Attach left and right side panels to sides of bottom shelf with (4) M6x13 screws, M6 lock washers and M6 flat washers (Dia 16). (A) [] Attach back panel to bottom shelf and two side panels with (6) M4xl0 screws. (B) [] Attach tank baffle bar to back panel and bottom shelf with (2) M4xl0 screws. (C) [] Align door bracket holes with holes on side pa
Summary of the content on the page No. 19
Front Doors [] Remove the (4) M4xlO screws pre-assembled to the door handle ends, and use them to attach handles to doors. [] Insert the lower door pin into the hole on the bottom shelf. Pushdown the upper door pin, align it beneath hole in door pin bracket, and release pin so that it inserts in hole. [] Repeat this for the other door. [] Note: If the doors do not line up when closed or cannot close freely, loosen the screws on the door pin bracket. Adjust the door pin bracket as necessary, and
Summary of the content on the page No. 20
Grill Head to Cart This step requires two people to lift and position grill head onto cart. Remove the tie wraps securing regulator hose to underside of grill head. Pull hose and igniter wires out to side of grill head. [] Carefully lower the grill head onto the cart. Make sure the regulator hose and igniter wires are hanging outside the cart. Open lid and attach head to cart with (4) M6x13 screws and M6 compression washers. M6X13 screw Qty: 4 pcs M6 compression washer Qty: 4 pcs @ @ @ @ @ 20 •
