Summary of the content on the page No. 1
34942G
Gas hob
GB
Operating Instructions
Summary of the content on the page No. 2
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350 350 Installation This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. Remove all packaging before using the hob. Ensure that the gas and electrical supply complie
Summary of the content on the page No. 3
When using the hob for a long period of time, the ventilation should be improved, by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstabl
Summary of the content on the page No. 4
Contents Important Safety Information .................................................................... 2 Instructions for the User .............................................................................. 6 Description of the Hob........................................................................................... 6 Operation ................................................................................................................... 7 Maintenance and Cleaning ...............
Summary of the content on the page No. 5
Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instructions for an operation Hints and Tips Keep this instruction book for future reference and ensure it is passed on to any new owner. These instructions are only valid for countries whose identification symbols are shown on the inside cover of this instruction booklet and on the appliance itself. This appliance is manufactured according to
Summary of the content on the page No. 6
Description of the Hob 3 1 2 3 4 6 7 5 8 1. Hob Top 9 2. Rapid Burner 10 3. Semi-rapid Burners 4. Triple-crown Burner 5. Auxiliary Burner 6. Control knob for back left burner (semi-rapid) 7. Control knob for back right burner (semi-rapid) 8. Control knob for front right burner (auxiliary) 9. Control knob for central burner (triple-crown) 10.Control knob for front right burner (rapid) INSTALLATION Any gas installation must be carried out by a registered CORGI installer, and in accordance with exi
Summary of the content on the page No. 7
Operation Hob burners control knobs The symbols on the knobs mean that : there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. To light a burner, turn the relevant knob anticlockwise to maximum position ( ), then push it down to ignite the burner. Upon ignition, adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. When swi
Summary of the content on the page No. 8
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for n
Summary of the content on the page No. 9
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM SOLUTION There is no spark when lighting Check that the unit is plugged in the gas and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e.g. after cleaning. The gas ring burns unevenly Check the mai
Summary of the content on the page No. 10
Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk When you contact the Service Centre, they will need the following information: 1. Your name, address and post code. 2. Your telephone number 3. Clear an
Summary of the content on the page No. 11
Guarantee Conditions Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG- Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workman- ship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating p
Summary of the content on the page No. 12
Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: 860 mm Depth: 500 mm Height: 88 mm Weight: 16 Kg CUT OUT DIMENSIONS Width: 830 mm Depth: 470 mm Thickness: 30 mm SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V 50 Hz, 220 V 60 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. HEAT INPUT Rear Left Burner (semi rapid) 2.0 kW (6824 BTU/HR) Front Left Burner (rapid) 3.0 kW Natural
Summary of the content on the page No. 13
Instructions for the Installer BURNER RAPID SEMI-RAPID AUXILIARY TRIPLE (large) (medium) (small) CROWN TYPE OF GAS POSITION MAX MIN MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER (kW) 3.0 0.65 2.0 0.45 1.0 0.33 4.0 1.2 NATURAL GAS 20 mbar NOMINAL FLOW 3 VALUE = RATE (m /h) 0.286 0.057 0.190 0.038 0.095 0.028 0.381 0.114 3 37.78 MJ/m NOZZLE 3 Ws - 50.7 MJ/ m REFERENCE 119 Adjust. 96 Adjust. 70 Adjust. 146 Adjust. (1/100 mm) LPG GAS NOMINAL THERMAL 28-30/37 mbar POWER (kW) 2.8 0.65 2.0 0.45 1.0 0.3
Summary of the content on the page No. 14
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a 3 volume of less than 20 m . If it is installed in a room of volume 3 2 less than 5 m an ai
Summary of the content on the page No. 15
50 mm 100 mm 50 mm 100 mm 50 mm 50 mm Installation CLEARANCES REQUIRED CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE WITH A COOKER HOOD ABOVE 700 mm 700 mm 650 mm 420 mm 420 mm 420 mm 420 mm FO 2028* FO 2027* Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a CORGI registered installer. The manufacturer will not accept liability, should the a
Summary of the content on the page No. 16
Installation FO 0814 FO 0264 A) End of shaft with nut B) Washer C) Elbow On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). When the fi
Summary of the content on the page No. 17
860 830 Building in Cut Out Size The dimensions of the cut-out are given in the diagram. FO 2407 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2 (see next page). 17 500 470 55 min.
Summary of the content on the page No. 18
Building in ON/OFF SWITCH ON/OFF SWITCH 12 FLEX OUTLET FLEX OUTLET FO 0764 FO 0763 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture 3 unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is a 60 shown in diagram 3. The panel fitted under the hob b ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("
Summary of the content on the page No. 19
Building in Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. Seal 1) Place the sealing a gasket all around the edge of the cut out. 2) Place the hob into the cut out and secure it by means of FO 0199 the relevant fixing clamps and screws, as shown in the diagram. 3) Re
Summary of the content on the page No. 20
Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V 50 Hz, 220 V 60 Hz electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate.
