Chamberlain ML5500 user manual

Summary of the content on the page No. 1

™
™
Instructions – Garage Door Operator
Model MotorLift 5500
Thank you for purchasing this Chamberlain product.
GB For Service: 0800 317847
IRL For Service: (0044) (0) 1935 848 525
114A2421D

Summary of the content on the page No. 2

GARAGE DOOR OPENER WARRANTY Chamberlain GmbH warrants to the first retail purchaser of this product that the product shall be free from any defect in materials and/or workmanship for a period of 60 full months (5 years) from the date of purchase. Upon receipt of the product, the first retail pur- chaser is under obligation to check the product for any visible defects. Conditions: The warranty is strictly limited to the reparation or replacement of the parts of this product which are found to be

Summary of the content on the page No. 3

START BY READING THESE IMPORTANT SAFETY RULES These safety alert symbols mean Caution – a personal safety or property damage instruction. Read these instructions carefully. This garage door opener is designed and tested to offer reasonable safe service provided it is installed and operated in strict accordance with the following safety rules. Failure to comply with the following instructions may result in serious personal injury or property damage. Caution: If your garage has no service entrance

Summary of the content on the page No. 4

8 ATTACH THE RAIL BRACKETS BEFORE YOU BEGIN: Align rail brackets (1) with end of rail assembly. Insert two hex screws (2) 1. Look at the wall or ceiling above the garage door. The door/header and lock nuts (3). Tighten securely. bracket must be securely fastened to structural supports. ASSEMBLY OF YOUR OPENER IS NOW COMPLETE. 2. Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware (not supplied) may be required. 3. Depending on your door's c

Summary of the content on the page No. 5

13 16 HANG THE OPENER INSTALL THE LIGHT AND LENS The opener must be securely fastened to a structural support of the Install a 40 watt maximum (230V/E27) light bulb (1) in the socket as garage. Attach the hanging brackets toward the front of the opener as shown. The light will turn on and remain lit for 4-1/2 minutes when power is shown (1). connected. After 4-1/2 minutes it will turn off. Three representative installations are shown. Yours may be different. Replace burned out bulbs with roug

Summary of the content on the page No. 6

19 21 PROGRAM YOUR OPENER & REMOTE FORCE ADJUSTMENT Activate the opener only when door is in full view, free of obstruction The force, as measured on the closing edge of the door, should not and properly adjusted. No one should enter or leave garage while exceed 150 N (15kg). If the closing force is adjusted to more than door is in motion. Do not allow children to operate push button(s) or 150 N, the Protector System must be installed. remote(s). Do not allow children to play near the door. D

Summary of the content on the page No. 7

MAINTENANCE OF YOUR OPENER OPERATION OF YOUR OPENER Once a Month: Your opener can be activated by any of the following devices: • Repeat safety reverse test. Make any necessary adjustments. • The Lighted Door Control Button. Hold the button down until door • Manually operate door. If it is unbalanced or binding, call for professional starts to move. garage door service. • The Outside Keylock or Keyless Entry System (if you have installed • Check to be sure door opens and closes fully. Adjust Li

Summary of the content on the page No. 8

HAVING A PROBLEM? (Continued) 25 ACCESSORIES 7. Opener noise is disturbing in living quarters of home: (1) Model 4330EML Single-Function Remote Control If operational noise is a problem because of proximity of the opener to the (2) Model 4333EML 3-Function Remote Control living quarters, Vibration Isolator Kit 41A3263 can be installed. This kit was designed to eliminate the "sounding board effect" and is easy to install. (3) Model 4335EML 3-Function Mini Remote Control 8. The garage door opens