Westinghouse MT80A TILT user manual

Summary of the content on the page No. 1

Installation and Assembly:
Universal Tilt Wall Mount for 15" - 37" Screens
Model: MT80A TILT
This product is intended for use with UL
Features: Listed products and must be installed by a


qualified professional installer.
• Fits 15" to 37" flat panel screens
• One-touch tilt for effortless positioning and adjustment of the screen Max UL Load Capacity: 80 lb (36.3 kg)
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer care call 1-866-287-5555.
ISSUED: 01-17-06 SHEET #:

Summary of the content on the page No. 2

Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Westinghouse product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call customer care at 1-866-287-5555. • This product should only be installed by a qualified professional. • Make sure that the wall will safely support the combined load of the

Summary of the content on the page No. 3

Parts List Description Qty Part # A adapter plate 1 095-4346 B tilt assembly 1 095-0360 Alligator® anchor 2 590-0097 C D M4 x 10 mm phillips screw 4 504-9012 E M4 x 20 mm phillips screw 4 504-9020 F retaining spacer 4 590-5005 G #14 x 2-1/2" hex head wood screw 2 5S1-015-C03 H M5 x 6 mm screw 1 520-1023 A B C D E F G H ISSUED: 01-17-06 SHEET #: 202-9091-1 3 of 8

Summary of the content on the page No. 4

Installation to Single Wood Stud Wall WARNING • Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components. Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based 1 on its edges, draw a vertical line down the stud’s center. Place tilt assembly (B) on wall as a template, making sure that the two mounting holes are over the stud centerline. Level tilt assembly, and mark the cent

Summary of the content on the page No. 5

SOLID CINDER BLOCK CONCRETE Installation to Solid Concrete or Cinder Block WARNING • When installing Westinghouse wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual con- crete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica- tions. It is suggested that a standard electric drill on slow s

Summary of the content on the page No. 6

Attaching Adapter Plate to Flat Panel Screen WARNING • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail. ® FOR VESA 75 MOUNTING PATTERN: FOR VESA 100 MOUNTING PATTERN: 2 Choose hole pattern as shown below. Attach adapter Choose hole pattern as shown below. Attach adapter plate (A) to back of screen using four M4 x 10 mm plate (A) to back of screen using four M4 x 10 mm s

Summary of the content on the page No. 7

Installing and Removing Flat Panel Screen Attach screen to tilt assembly (B). Tighten M5 x 6 SCREEN 3 mm screw (H) to lock screen to tilt assemby. Note: For security models, use security driver (I) to tighten M5 x 6 mm screws (H). H To remove screen from mount, loosen screw (H) and A lift screen off of mount. WARNING • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen. • Failure to lock adapter plate (A)

Summary of the content on the page No. 8

Limited Five-Year Warranty Westinghouse Digital Electronics warrants to original end-users of this Westinghouse display mounting product (the “Product”) that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5) years from the date of purchase by the original end-user, subject to the following terms and conditions: REPAIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, Westinghouse Digital Electronics wil