Summary of the content on the page No. 1
TECHNICAL MANUAL (Ver.1.1A)
PLASMA DISPLAY : PDP-501MX/PDP-V501X
TABLE-TOP STAND: PDK-5001
SPEAKER SYSTEM: PDP-S02-LR
This manual provides precautions and information for installation, preparation, and handling of the plasma display and
its dedicated mounting hardware.
Before installation and preparation work, choose a safe and appropriate site after thorough consideration of construction,
materials used, strength, and surroundings. If the adequate safeguards are not in place, immediately halt t
Summary of the content on the page No. 2
Table of Contents FEATURES ................................................................................................................................................. 4 SPECIFICATIONS 2.1 Specifications .....................................................................................................................................................6 2.2 External dimensions ....................................................................................................................
Summary of the content on the page No. 3
Table of Contents 5.3.3 Settings in Menu Mode ...........................................................................................................................74 1) Setting the three-dimensional Y/C separator .......................................................................................74 2) ABL On/Off ..........................................................................................................................................74 3) MP mode On/Off ..................
Summary of the content on the page No. 4
Features Features and Functions of the PDP-501MX Plasma Display • High-definition XGA wide panel The Display uses a high-definition XGA wide panel, which provides 1280 x 768 resolution with more than 980.000 pixels. This resolution is more than 2.5 times higher than that of conventional panels, and enables multimedia information to be reproduced more vividly and accurately than ever before. • Clear, high-quality image Provides 8-bit RGB in 256 gradations/16.77 million colors. A new exclusive tec
Summary of the content on the page No. 5
Features 5
Summary of the content on the page No. 6
Specifications 2.1 Specifications (U.S. Model and Taiwanese Model) Light-emitting panel: ...... 50-inch plasma display panel Control Terminal RS-232C (for control using a PC) Aspect ratio: ........................................................... 16:9 Connector type: D-sub, 9-pin PEL: ................................. 1280 x 768 (XGA supported) Baud rate: 1200, 2400, 4800, 9600, 19200 bps PEL pitch: ................ 0.858 (H·RGB trio) x 0.808 (V) mm (NOTE 5) Gradation: ........................
Summary of the content on the page No. 7
Specifications NOTE 1 To prevent malfunctions and breakdowns, avoid Signals supported by INPUT 3/4 (video) —1 of 2 connecting the RCA jack and BNC terminal Vertical Horizontal Signal Remarks Frequency Frequency simultaneously, since they are electrically Format connected to each other inside the body. Fv (Hz) Fh (kHz) RGB (Note 9) 60 SDTV 480i 15.7 NOTE 2 If the RCA jack or the BNC terminal is connected Component at the same time as the S terminal, signals RGB SDTV 480p 31.5 received at the S te
Summary of the content on the page No. 8
Specifications 2.1 Specifications (EURO Model) Light-emitting panel: ...... 50-inch plasma display panel Control Terminal RS-232C (for control using a PC) Aspect ratio: ........................................................... 16:9 Connector type: D-sub, 9-pin PEL: ................................. 1280 x 768 (XGA supported) Baud rate: 1200, 2400, 4800, 9600, 19200 bps PEL pitch: ............... 0.858 (H)(RGB trio) x 0.808 (V) mm (NOTE 5) Gradation: ........................ 256/16.77 million f
Summary of the content on the page No. 9
Specifications NOTE 1 To prevent malfunctions and breakdowns, avoid Signals supported by INPUT 3/4 (video) —1 of 2 connecting the RCA jack and BNC terminal Vertical Horizontal Signal Remarks Frequency Frequency simultaneously, since they are electrically Format Fv (Hz) Fh (kHz) connected to each other inside the body. 50 15.6 RGB (Note 9) NOTE 2 If the RCA jack or the BNC terminal is connected Component at the same time as the S terminal, signals 31.3 RGB received at the S terminal receive prior
Summary of the content on the page No. 10
External Dimensions 2.2 External Dimensions Weight: 43.0 kg Material: Front: Resin; Rear: Resin Treatment: Front: Laser-satin gray paint; Rear: Laser-satin gray paint For packaging information, refer to 3.3.2 Unpacking : Center of gravity (Unit: mm) 31 98.5 609 1218 65.5 1108 Light sensor for the remote Rear View 1162 104 590 104 104 104 496 24-M8 (ø16 mm, with hole rivet) 10 714 628 150 150 357 250 250 660
Summary of the content on the page No. 11
External Dimensions < Main Switch > < Main Unit Operation Panel > < Light Sensor for the Remote > 11
Summary of the content on the page No. 12
Controls and Connectors 2.3 Controls and Connectors < Operation Panel > STANDBY /ON 3 8 INPUT 4 MENU 5 ADJUST 6 1 2 SET 7 POWER 9 0 - = ~ ! @ # $ < Connectors > (at the rear of the main unit) YCB/PB CR/PR 75Ω 2.2kΩ INPUT 4 OUTPUT GB R HD VD (INPUT 4) (ON SYNC) INPUT 3 (H/V SYNC) % ^ & * ( ) _ + Á
ª
S - VIDEO VIDEO OUTPUT Y CB/PB CR/PR IN OUT IN OUT ë
RS - 232C C. VIDEO INPUT 1 (INPUT 1) INPUT 2 CONBINATION CONTROL < Main Power Switch Section > < Connectors > 1 STANDBY/ON indicator 9 AC INLET
Summary of the content on the page No. 13
Controls and Connectors INPUT 4 Input INPUT 2 Input # INPUT 4 input terminal Component video input terminals composed of three RCA Mini D-Sub 15-pin terminal for connection of RGB jacks ( to _. signals This terminal also supports component signals (settings ( Y Input: 75Ω required in the menu screen). ) CB and PB Input: 75Ω This terminal supports Microsoft Plug & Play (VESA _ CR and PR Input: 75Ω DDC 1/2B). (VESA is a registered trademark of the Video Electronics Control Standards Association.)
Summary of the content on the page No. 14
Remote Control Unit 2.4 Remote Control Unit STANDBY/ON Power switch INPUT1 INPUT2 INPUT3 INPUT4 Used to turn the system on or off Input switches VIDEO C.VIDEO RGB RGB (standby) S-VIDEO ( RCA ) ( BNC ) ( D-sub ) Used to select inputs Full Auto-Zoom button FULL AUTOSCREEN DISPLAY ZOOM SIZE Used to turn full auto-zoom on or off Screen Size switch MENU Used to select screen size Display button Used to view status of inputs or SET Adjustment buttons settings Used to move the cursor in the menu screen
Summary of the content on the page No. 15
Remote Control Unit 15
Summary of the content on the page No. 16
Installation Site Requirements 3.1 Installation Site Requirements If the site requires modifications or special preparations for installation of the plasma display or its mounting hardware, obtain permission in advance from the building owner or building authorities. To ensure installation safety, it is also important to determine the strength of the installation site with the help of the original building contractor. Safety Precautions 1) Structure of the installation site Make sure you thor
Summary of the content on the page No. 17
Installation Site Requirements 9) Temperature and humidity conditions • The installation site should meet the following conditions: • Operating temperatures: 0 to 40 °C (largely depending on installation conditions) • Operating humidity: 20 to 80% • Storage temperature: –10 to +45 °C • Storage humidity: 20 to 90% • Operating atmospheric pressure: 0.9 to 1.1 atm • Storage atmospheric pressure: 0.6 to 1.5 atm • We recommend against installing electronic products such as this unit in locations sub
Summary of the content on the page No. 18
Installation Conditions 3.2 Installation Conditions 3.2.1 Heat dissipation This unit has openings for effective ventilation at locations marked by arrows in the illustration below. To allow proper dissipation of heat from the unit, avoid blocking or covering any of these openings. 75 96.5 35 Ø 5 10 Fan (4 in number) 345 70 54 85 45 215 255 Air flow through the openings: All four fans exhaust hot air from the unit. All openings not assisted by fans serve as air inlets. If the unit is hung from or
Summary of the content on the page No. 19
Installation Conditions 3.2.2 Calculating heat quantity . For power consumption, allow for 600 VA ( = .600 W) per unit. Since most of the power consumed is transformed into heat, power consumption may be regarded as roughly equal to generated heat. 1 Conversion to calories [W] x 0.86 = [kcal/h] Heat generated per display: 600 W x 0.86 = 516 kcal/h 2 Conversion to British Thermal Units (BTU) [W] x 3.41 = [BTU/h] Heat generated per unit: 600 W x 3.41 = 2046 BTU/h 3.2.3 Product mounting holes W
Summary of the content on the page No. 20
Installation Conditions This unit is designed to be mounted using four bolt holes. For additional safety, we recommend securing it at six to eight points on opposite sides of the horizontal and vertical center lines, as shown in the illustration below. Do not secure the unit at four points arranged in a single row, as shown below. Methods for securing — Unfavorable examples Methods for securing — Favorable examples B. Secured at six points A. Secured at eight points C. Secured at four points (wi
