Summary of the content on the page No. 1
22-TON AIR/HYDRAULIC
BOTTLE JACK
Model 66242
SET Up AND OpERATINg INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MAN
Summary of the content on the page No. 2
NOTICE is used to SAVE THIS MANUAL Notice address practices Keep this manual for the safety not related to personal injury. warnings and precautions, assembly, CAUTION, without operating, inspection, maintenance and CAUTION the safety alert cleaning procedures. Write the product’s symbol, is used to address serial number in the back of the manual near practices not related to the assembly diagram (or month and year of personal injury. purchase if product has no number). Keep thi
Summary of the content on the page No. 3
b. Use safety equipment. Always adjustments, changing accessories, wear ANSI-approved safety impact or storing the tool. Such preventive goggles and heavy-duty work safety measures reduce the risk of gloves. Safety equipment such starting the tool accidentally. as non-skid safety shoes, hard d. Store idle tools out of the reach of hat, or hearing protection used for children and do not allow people appropriate conditions will reduce unfamiliar with the tool or these personal injuries
Summary of the content on the page No. 4
2. Use clean, dry, regulated, being lifted. Align the saddle of the compressed air at 90-145 pSI. Do jack stand directly under the vehicle’s not exceed the recommended seam or recommended lifting point. maximum air pressure. Do not use 14. When lifting the entire front end or oxygen, carbon dioxide, combustible rear end of a vehicle, make sure to gases, or any other bottled gas as a support the load immediately with power source for this tool. two jack stands. Align the saddles 3. D
Summary of the content on the page No. 5
21. The warnings, precautions, ASSEMBLY and instructions discussed in this instruction manual cannot 1. Assemble the Handle and its 6.x cover all possible conditions and series parts that come in Box B. (See situations that may occur. It must Assembly Drawing.) be understood by the operator that Adjustable Rod (6.3) common sense and caution are factors which cannot be built into this Adapters (12.1, 12.3, product, but must be supplied by the 12.4) operator. Spring Washers U-Bolts
Summary of the content on the page No. 6
Tool Set Up Completed Handle Set Screw (2.5) Fig. 2 4. Put the Handle Assembly into Handle Fig. 3 Socket and secure with Set Screw. 1. This Jack comes in two boxes and (See Fig. 2.) easily connects to an air compressor. For proper Jack/Air compressor con- OpERATINg INSTRUCTIONS nection, see Fig. 3. Read the ENTIRE IMpORTANT 2. Incorporate an in-line oiler, shut-off SAFETY INFORMATION section valve, regulator with pressure gauge, at the beginning of this manual and filter for best ser
Summary of the content on the page No. 7
IMpORTANT: Prior to use, check for Then chock the wheels that are not proper hydraulic oil level in the Bottle being lifted. Jack. (See page 9) 7. Check to make sure the Bottle Jack 4. Thoroughly test the Jack for proper is fully lowered. If not, turn the Knob operation prior to its actual use. If (6.11) counterclockwise to lower the the Jack appears not to be working Jack. Once the Jack’s ram is fully properly, it may be necessary to lowered, turn the Knob clockwise to purge its hyd
Summary of the content on the page No. 8
2. Turn on air compressor, and set its stand(s) causing personal injury and/ regulator to 90-145 pSI. Do not ex- or property damage. ceed 145 pSI. Allow the compressor 8. When the repair work to the vehicle to build up pressure and cycle off. is completed, and prior to lowering 3. Depress the Lever of the Air Valve the vehicle. Make sure to remove Assembly (5) until the Saddle of the all tools, old vehicle parts, etc. from Bottle Jack has nearly reached the under the vehicle. vehicle li
Summary of the content on the page No. 9
onto the ground. (See Assembly BLEEDINg INSTRUCTIONS: Diagram.) 3. Before each use or when the Bottle 3. Lower the Bottle Jack completely Jack lacks in performance, make (Be aware that it will take a good sure to check for excessive air and amount of effort to lower the ram proper hydraulic oil level in the Bottle down to be level with the reservoir). Jack. If the Jack appears not to be Do not hammer on the ram. Store working properly, it may be neces- the Jack in a clean, dry, safe l
Summary of the content on the page No. 10
of children and other unauthorized people. SKU 66242 For technical questions, please call 1-800-444-3353. Page 10
Summary of the content on the page No. 11
pLEASE READ THE FOLLOWINg CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS UALIFIED q TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACE
Summary of the content on the page No. 12
ASSEMBLY DIAgRAM SKU 66242 For technical questions, please call 1-800-444-3353. Page 12
Summary of the content on the page No. 13
pARTS LIST part Description part Description part Description 1.1 Cover 2.13 3.34 Steel Wire 1.2 Saddle 2.14 Screw 3.35 Connecting Block 1.3 Extension Screw 2.15 Washer 3.36 Fork Axle With Hole 1.3a Spring Pin 2.16 Bolt 3.37 Spring Pin 1.4 Spring Support 2.17 Washer 3.38 Spring Pin 1.5 Screw Bushing 3.39 Connecting Axle 1.6 Y-Shape Seal Ring 3.1 Screw 3.40 Spring Pin 1.7 Head Nut 3.2 Washer 1.8 O-Ring 3.3 Spring 4 Air Pump 1.9 Piston Rod 3.4 Steel Ball 4.1 Packing 1.10 Stop Ring 3.5 Valve Core 4
Summary of the content on the page No. 14
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installati
