Summary of the content on the page No. 1
®
ViewSonic
N2060w
LCD TV
-
- 使 用 手 冊
- User Guide
Model No. : VS11287-1G
Summary of the content on the page No. 2
CONTENTS Important Safety Instructions --------------------------------------------------1 Copyright Information ------------------------------------------------------------ 2 Antenna Installation Instructions---------------------------------------------- 3 Cleaning the LCD TV ------------------------------------------------------------3 CONNECT PERIPHERAL EQUIPMENT Front Panel Control Knobs ---------------------------------------------------- 4 Preparation --------------------------------------
Summary of the content on the page No. 3
Important Safety Instructions 1. Read these instructions completely before using the equipment. 2. Keep these instructions in a safe place. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this equipment near water. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the LCD TV” in this guide for further instructions. 7. Do not block any
Summary of the content on the page No. 4
Copyright Information ® Copyright © ViewSonic Corporation, 2006. All rights reserved. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. Disclaimer:ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product. In the interest of continuing product improveme
Summary of the content on the page No. 5
Antenna Installation Instructions 1. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges, Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, connection to grounding
Summary of the content on the page No. 6
CONNECT PERIPHERAL EQUIPMENT FRONT PANEL CONTROL KNOBS Source(信号源)①: Press to select your input source. Volume（音 量）②③: Press to confirm your function selection (when the OSD main menu displayed) or adjust volume (without OSD main menu) Channel（ 频道） ④⑤: Select the intended function by pressing the two keys (when the OSD main menu displayed), or switch the channels in the TV mode (without OSD main menu) Menu( )⑥: Press to show the OSD menu and exit OSD m
Summary of the content on the page No. 7
There is a wide range of video and audio equipment that can be connected to your TV. The following connection diagrams show you how to connect them. PREPARATION Lay the LCD TV with the screen down on a table, as it will be easier to connect your peripheral equipment. Please take precaution on page8 not to damage the screen. 1. VGA audio input 2. VGA input 3. AC power input terminal 4. Headphone outlet 5. AV signal input 6. Left audio track input (AV/S-Video) 7. Right audio trac
Summary of the content on the page No. 8
OPERATING INSTRUCTIONS USE OF THE REMOTE CONTROL POWER (电源) Mute(静音) Press to turn on/off the Temporarily interrupt the TV. The TV is never sound or restore it. completely powered off unless it is physically Status(状态) unplugged. (1) Display the channel number when input TV Channel (频道) RF Press or to browse (2) Display input source through the TV when input the other channels。 sources. Volume (音量) Pr
Summary of the content on the page No. 9
3. Remote control: Remove the cover of the battery compartment. Insert the 2 batteries supplied (Type AAA 1.5V). CAUTION Only use the specified AAA batteries. Do not mix new and old batteries. This may result in cracking or leakage, which may pose a fire risk or lead to personal injury. Insert batteries according to the (+) and (-) markings. Inserting the batteries incorrectly may result in cracking or leakage, which may pose a fire risk or lead to per-sonal injury. Dispose o
Summary of the content on the page No. 10
PREPARATION 1. Assembly Take out TV and base from carton, assembled by three pieces screws, which you could find from the accessory box. Shown in the figures below: Place the base on a solid surface Note: Lock the screw middle first, then the others, to avoid holes aiming incorrectly ViewSonic 8 N2060w
Summary of the content on the page No. 11
2. Place the TV on a solid surface. Ensure that the TV is placed in a position to allow free flow of air. Do not cover the ventilation openings on the back cover. To prevent any unsafe situations, no naked flame sources, such as lighted candles, should be placed on or in the vicinity. Avoid heat, direct sunlight and exposure to rain or water. The equipment shall not be exposed to dripping or splashing. Insert the aerial plug firmly int
Summary of the content on the page No. 12
TO USE THE MENUS 1. Press the MENU button to display or close main menu. 2. Use the cursor up/down to select a menu item. 3. Use the cursor left/right to enter a submenu or enable/disable the function. 4. Press the MENU button to exit the menu. MAIN MENU Press the MENU button to enter the main OSD (On Screen Display). Adjust items including Sound Setup, Picture Setup, Function Setup and TV setup. When the input source is PC, YPbPr, AV or S-VIDEO mode, only the Sound Setu
Summary of the content on the page No. 13
Sound Setup (Same for all modes) 1. The range of adjusting volume, bass and treble is from 0~100. 2. Select “ON” or “OFF” in Audio selection to control the sound output. 3. The range of adjusting Balance is -50~+50; when adjusting from 0 to -50, the sound from the right track fades until silence; when adjusting from 0 to +50, the sound from the left track fades until silence. 4. AVL: you can set it “ON” or “OFF”. The function is to adjust the input sound automatically. You may enable t
Summary of the content on the page No. 14
Picture Setup When the input source is in PC mode, shown in the figure below: 1. Brightness and Contrast: The range can be adjusted from 0~100. 2. Position: There are two options, Horizontal and Vertical, which can be adjusted from -50 to +50. 3. Video noise: There are two options, Phase and Clock, which can be adjusted from -50 to +50. 4. Sharpness: Select from six options Softest, Soft, Normal, Sharp, Sharpest and Auto. You may adjust the above options according to your
Summary of the content on the page No. 15
When the input source is TV, YPbPr, AV or S-VIDEO mode, shown in the figure below: 1. Brightness and Contrast: The range can be adjusted from 0~100; use Brightness and Contrast options to adjust the brightness of picture. 2. Color: The range can be adjusted from 0~100; use this option to adjust the color saturation of picture. 3. Sharpness: Select from six options: Softest, Soft, Auto, Sharp, sharpest and Auto. You can adjust the sharpness of picture using any option above. 4.
Summary of the content on the page No. 16
Function Setup, shown in the figure below: 1. OSD time out: could set OSD display time from 10 seconds to 60 2. Language: could set OSD language to English, simplfied Chinese or traditional Chinese 3. Sleep timer: set the time after which the product will enter standby status automatically 4. Reset to default: It is used to reset the OSD settings. 1. Sleep timer：Start to count down after the sleep timer set, could choose from 5 min. to 120 min. Count down shown on the s
Summary of the content on the page No. 17
TV setup The following menu appears only in the TV mode. o 1. Program no. : Shows the current channel number 2. Color system: shows the current picture input system（shows auto after auto search） 3. Sound system: shows the current sound input system（shows auto after auto search） 4. Auto search: Used to auto search and storage program 5. Frequency: Shows the frequency of current channel. Could adjust frequency slightly by the right and left button to get the result what you want
Summary of the content on the page No. 18
HEADPHONE 1. The headphone jack is located at the right side of the TV. 2. The MUTE key on the remote control works on both internal speaker and the headphone. 3. Use volume key to adjust the volume. TIPS Care of the screen Do not rub or strike the screen with anything hard as this may scratch, mar, or damage the screen permanently. Unplug the power socket before cleaning the screen. Dust the TV by wiping the screen and the cabinet with a soft, clean cloth. If the scr
Summary of the content on the page No. 19
Appendix Specifications Panel Type 20” TFT-LCD Active Matrix wide-XGA, 1360x 768 Color Anti-glare coating Viewing angles 160° H/ 160° V Input signal Video Fh: 32-48KHz, Fv: 50-60Hz VGA input*1
Summary of the content on the page No. 20
Storage Temperature -25℃ to 60℃ conditions Humidity 10% to 85%(no condensation) Dimension Physical 521.84mm(W) x 419.52mm(H) x 180.83mm(D) 20.55”(W) x 16.52”(H) x 7.12”(D) Package 595mm(W) x 512mm(H) x 226mm(D) 23.4”(W) x 20.2”(H) x 8.9”(D) Weigh
