Edelbrock 1802 user manual

User manual for the device Edelbrock 1802

Device: Edelbrock 1802
Category: Automobile Parts
Manufacturer: Edelbrock
Size: 0.37 MB
Added : 6/20/2014
Number of pages: 6
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Edelbrock 1802. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Edelbrock 1802.

For your convenience

If looking through the Edelbrock 1802 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Edelbrock 1802 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Edelbrock 1802 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Edelbrock 1802 User manual - Online PDF
Advertisement
« Page 1 of 6 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Edelbrock 1802 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Edelbrock 1802. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

EDELBROCK THUNDER SERIES AVS CARBURETORS
Part #1801, 1802, 1803, 1804, 1805,
1806, 1812, 1813, 1825, 1826
INSTALLATION INSTRUCTIONS
PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation,
it is recommended to have the installation completed by a qualified mechanic.

Summary of the content on the page No. 2

RECOMMENDED TOOLS ❑ Sockets/wrenches/tubing wrenches ❑ #20 Torx Driver (for electric choke models) ❑ Pliers ❑ Wire crimpers (for electric choke models) ❑ Screwdrivers ❑ Test Meter or Test Light (for electric choke models) ❑ Hacksaw and/or tubing cutter PARTS RECOMMENDED FOR INSTALLATION ❑ New Fuel Filter (Edelbrock #8135 or equivalent) or Fuel Line/Filter ❑ Electrical connectors (electric choke carburetors) kit such as Chrome Steel Fuel Line Kit #8134, Dual Feed Line ❑ Carburetor adapter, for ot

Summary of the content on the page No. 3

BEFORE REMOVING OLD CARBURETOR 3. Always use a new fuel filter. Failure to do so will void the 1. Determine if the distributor vacuum port is timed (no warranty. vacuum at idle) or full (vacuum present at idle). With the engine fully warmed up and idling, pull the vacuum hose off of the 4. Edelbrock Adapter #2696 or Adapter/Fuel Line Kit #2697 must be carb and "feel" for vacuum by putting your finger on the vacuum used when installing a Thunder Series Carburetor on a General port (See Fig. 2). I

Summary of the content on the page No. 4

CARBURETOR REMOVAL CARBURETOR PREPARATION 1. Prior to removal make sure that the engine is cool. 1. Compare throttle arm of your new carburetor with the old one to be sure that all required linkages will hook up. Install proper throttle 2. Disconnect negative battery cable from battery. and transmission linkage for your particular application. Throttle stud is removable and must be installed in the proper location. 3. Remove air cleaner. Be sure to carefully disconnect any hoses from Chrysler ve

Summary of the content on the page No. 5

CARBURETOR INSTALLATION Manual choke cable and 1. Remove rag from intake manifold and install new studs, mounting fuel line connection gasket and adapters (where applicable). NOTE: Do not use any cement, glue, or RTV sealant on gasket. 2. Carefully place new carburetor on gasket. 3. Replace all mounting nuts and washers. EnduraShine™ finish carburetors should use the supplied 5/16” flat washers under any other washers used. Hand tighten with a short box end wrench, alternating between diagonally

Summary of the content on the page No. 6

10. Mark air cleaner stud for proper length, remove from carburetor and ADJUSTING THE AIR VALVE SECONDARY cut with hack saw. Deburr stud and re-install in carburetor (See 1. With Torx drive (T15) and flat blade screw driver in place, loosen Fig. 11). Torx screw, make sure flat blade is secure to prevent loss of spring pressure (See Fig 12). 2. If you lose spring pressure, turn flat blade screw counter-clockwise until the air valve reaches closed position plus 1-1/2 turns to achieve the factory s


Alternative user manuals
# User manual Category Download
1 Edelbrock 1109 User manual Automobile Parts 5
2 Edelbrock 1107 User manual Automobile Parts 2
3 Edelbrock 1208 User manual Automobile Parts 0
4 Edelbrock 1221* User manual Automobile Parts 1
5 Edelbrock 1222* User manual Automobile Parts 0
6 Edelbrock 1209 User manual Automobile Parts 1
7 Edelbrock 1400 User manual Automobile Parts 2
8 Edelbrock 1477 User manual Automobile Parts 8
9 Edelbrock 1483 User manual Automobile Parts 0
10 Edelbrock 15004 User manual Automobile Parts 0
11 Edelbrock 15010 User manual Automobile Parts 0
12 Edelbrock 15017 User manual Automobile Parts 0
13 Edelbrock 15016 User manual Automobile Parts 0
14 Edelbrock 15042 User manual Automobile Parts 0
15 Edelbrock 15521 User manual Automobile Parts 0
16 Sony BP-GL95 User manual Automobile Parts 25
17 Sony BP-GL65 User manual Automobile Parts 2
18 Philips Epic 50PF9966 User manual Automobile Parts 3
19 Philips HTS3011 User manual Automobile Parts 2
20 Philips SDJ6040W User manual Automobile Parts 1