Summary of the content on the page No. 1
Plasma Display
ELECT
with Media Station
PS42P2SB
PS50P2HB
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
REMOTE CONTROL
ON-SCREEN MENUS
PICTURE IN PICTURE
TELETEXT
ENG
Summary of the content on the page No. 2
Safety Instructions ENG Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall. Do not expose the PDP to extreme temperature conditions or to extreme humidity conditions. Do not expose the PDP to direct sunlight and other sources of heat. Do not expose the PDP to any liquids. Never put objects of any kind into the television, and do not place a water-containing vessel on the PDP. During a storm conditions (especially when there is lightnin
Summary of the content on the page No. 3
Caution ENG CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ! CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE REAR COVER, NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash and arrow head The main voltage is indicated on the ☛ within the triangle is a warning sign rear of the PDP and the frequency is alerting you of “dangerous voltage” 50 or 60Hz. inside the product. The exclamation point within the WARNING: TO PREVENT DAMAGE WHICH MAY triangle i
Summary of the content on the page No. 4
ENG Contents (continued) FOREWORD Safety Instructions............................................................................................... 2 User Instructions ................................................................................................. 2 Caution................................................................................................................ 3 Checking Parts.....................................................................................
Summary of the content on the page No. 5
ENG Contents USING YOUR DISPLAY Setting the Dolby Surround................................................................................. 33 Adjusting the Dolby Pro Logic Preferences......................................................... 35 Adjusting the Headphone Preferences ............................................................... 36 Hearing the Melody Sound.................................................................................. 37 Setting the Current Time .....
Summary of the content on the page No. 6
Viewing the Plasma Display The actual configuration on your PDP may be different, depending ➢ ENG on your model. Front Panel Speaker Speaker POWER Remote Control Signal Receiver Press to turn the PDP on Aim the remote control towards this spot and off. on the PDP. SOURCE External input selection. MENU Menu display. - + Volume adjustment. C/P. Channel selection MUTE Temporary sound switch off. Rear Panel DISPLAY SIGNAL IN POWER IN Connect the video cable between the PDP Plug the mains lead in
Summary of the content on the page No. 7
Viewing the Media Station ENG Front Panel Channel selection Headphone connector S-Video input Power On/Off Stand by /Power On indicator On-Screen display Audio inputs Temporary sound switch off External input selection Video input Menu display Volume adjustment Rear Panel For further details about connection, refer to pages 48~51. ➢ e f g d a m l i c b k h j a) VHF/UHF (75Ω ) f) AUDIO OUT (L/R) 75Ω Coaxial connector for Aerial/Cable Network. Audio outputs for an audio system. b) MONITOR OUT / AV
Summary of the content on the page No. 8
Remote Control Buttons ENG AUTOMATIC SWITCH-OFF PIP FUNCTIONS; VCR/DVD FUNCTIONS; - PIP ACTIVATING OR DEACTIVATING - STOP (Stop) (PIP ON) - REWIND (Rew) - SWAPPING THE MAIN AND THE SUB - PLAY/PAUSE (Play/Pause) PICTURE (Swap) - FAST FORWARD (FF) - SELECTING THE LOCATION OF SUB PICTURE (Locate) - SELECTING THE CHANNEL OF SUB PICTURE (P/) Power - SETTING THE SIZE OF SUB PICTURE (Size) - SELECTING THE INPUT SOURCE (Source) POWER ON/OFF - SCANNING THE CHANNEL OF SUB PICTURE (Scan) MAKE THE REMOTE
Summary of the content on the page No. 9
Inserting the Batteries in the Remote Control ENG You must insert or replace the batteries in the remote control when you: Purchase the PDP Find that the remote control is no longer operating correctly 1 Remove the cover on the rear of the remote control by pressing the symbol downwards and then pulling firmly to remove it. 2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking care to respect the polarities: - on the battery against - on the remote control + on the battery aga
Summary of the content on the page No. 10
Installing the Display on the Wall Attachment Panel Wall attachment panel is sold separately. Check with your dealer ➢ ENG 1 Check for the stability of the wall where the PDP is to be installed. If the wall is not enough strong to support the PDP, strengthen the wall before installation. 2 Fix the wall attachment panel on the wall using bolts as shown in the figure: Fixing bolts must protrude from the wall appox. 1.5 cm. 3 Using the wall attachment panel, you may adjust the angle of the display
Summary of the content on the page No. 11
Installing the Display on the Wall Attachment Panel ENG 4 Remove four large screws from the rear side of the display. Insert the bolts, dish-type washers, and insulation rubber into the four screw-holes as shown in the figure: Bolt Insulation rubber 5 Hang the protruding plastic part on the rear of the PDP up the groove on the top of the wall attachment panel. Then, lift down the PDP. (Do not lift down the PDP with too much force. The protruding plastic part might be Œ taken off.) ´ 11
Summary of the content on the page No. 12
Separating the Display from the Wall Attachment Panel ENG After lifting the PDP up, pull it forward and remove it from the wall attachment panel. Œ ´ 12
Summary of the content on the page No. 13
Connecting Speakers ENG Connecting PDP and Speakers Fix the bracket onto the guide pole located on the rear of Guide pole speaker and fasten the screws. After removing the three screws on the PDP, clamp the speaker and the PDP together and fasten the screws. Guide pole Connecting Stand and Speakers When moving your PDP, do NOT hold the ➢ speaker connected to your PDP. It may damage the bracket clamping the speaker and your PDP together and Guide pole result in a drop of your PDP and a risk of
Summary of the content on the page No. 14
Connecting to an Aerial (or Cable Television Network) ENG To view television channels correctly, a signal must be received by the set from one of the following sources: An outdoor aerial A cable television network A satellite network Rear of the Media Station 1 In the first three cases, connect the aerial or network input cable to the 75Ω coaxial socket on the rear of the Media Station. or 2 If you are using an indoor aerial, you may need to turn it when tuning your television until you ob
Summary of the content on the page No. 15
Switching On and Off ENG 1 Plug the mains lead of the PDP and Media Station into an appropriate socket. 2 Connect the video cable between the DISPLAY SIGNAL IN on the rear of the PDP and the DISPLAY SIGNAL OUT on the rear of the Media Station. 3 Press the POWER button on the front panel of the Media Station or remote control to switch the display on. Do not connect the power cord ☛ Rear of the PDP between PDP and Media Station. Otherwise, the EMI characteristic will become worse because power
Summary of the content on the page No. 16
Becoming Familiar with the Remote Control ENG The remote control is used mainly to: Change channels and adjust the volume Display the on-screen menu system The following table presents the most frequently used buttons and their functions. Button Viewing Function Menu Function Power Used to display the next - P stored channel. P Used to display the - previous stored channel. to Used to display the corresponding channels. For double digit channels, the second digit must be ➢ pushed immediately
Summary of the content on the page No. 17
Setting up your Remote Control ENG 1 Turn off your VCR, Cable box, or DVD. 2 Press the Select button repeatedly to activate another component (VCR, Cable, DVD). Example: If you want to program the remote control to operate your VCR, make sure that the VCR LED is illuminated. 3 Press the Power button on the remote control. The component you select should turn on. If it turns on, your remote control is now set correctly. 4 Once your remote control is set up, press the Select button any time you wa
Summary of the content on the page No. 18
Plug and Play ENG When the Media Station is initially powered ON, several basic customer settings proceed automatically and subsequently. The following settings are available. 1 If the Media Station is in Standby mode, press the Power button on the remote control. Result: The message Plug & Play is displayed. It flickers for a little while, and then the Language menu is automatically displayed. 2 Select the appropriate language by moving the joystick left or Plug & Play right. Press the MENU bu
Summary of the content on the page No. 19
Choosing Your Language ENG When you start using your PDP for the first time, you must select Function the language which will be used for displaying menus and Language English indications. Time Size Normal Image Lock 1 Press the MENU button. Melody On Result: The main menu is displayed. 2 Move the joystick up or down until the Function is selected. Move Select Menu Result: The options available in the Function group are displayed. 3 Press the joystick button. Result: The Language is selected. 4
Summary of the content on the page No. 20
Storing Channels Automatically ENG You can scan for the frequency ranges available to you, (availability Channel depends on your country). Automatically allocated programme Area ASIA / W.EUROPE numbers may not correspond to actual or desired programme Auto Store numbers. However you can sort numbers manually and clear any Manual Store Channel Sort channels you do not wish to watch. Channel Edit Fine Tune 1 Press the MENU button. Move Select Menu Result: The main menu is displayed. 2 Move the joy
