Summary of the content on the page No. 1
BN68-00966A-00Cover.qxd 10/4/05 3:05 PM Page 1
LCD TV
LE26R52BD
LE32R52BD
-
AFTER SALES SERVICE
-
Do not hesitate to contact your retailer or service agent if a
change in the performance of your product indicates that a
faulty condition may be present.
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other Europ
Summary of the content on the page No. 2
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 2 Precautions When Displaying a Still Image A still image may cause permanent damage to the TV screen. WARNINGS: Image retention, commonly known as screen burn-in, can occur on most types of television if the same image is displayed continuously. The most common causes of image retention are logos that remain stationary on the TV screen. These logos are common on many programmes received via a Setop Box. To reduce this risk, avoid displaying still
Summary of the content on the page No. 3
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 3 Note : If there are borders around the displayed picture (top or sides), then extended viewing could result in the border leaving a trace image on the screen. Do not leave the screen in pause mode for extended periods of time as you may experience temporary or permanent image burn. Note : If the borders at the left, right and the center of the screen remain fixed for an extended period of time, the amount of light transmission will also remain v
Summary of the content on the page No. 4
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 2 Contents CONNECTING AND PREPARING YOUR TV Viewing the Control Panel ............................................................................................................................... 4 Viewing the Connection Panel......................................................................................................................... 5 - Connecting an Aerial or Cable Television Network .................................................
Summary of the content on the page No. 5
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 3 Contents SETTING THE OTHERS Activating the Child Lock ........................................................................................................................ 45 Setting the Blue Screen Mode................................................................................................................ 46 Selecting the Melody ...........................................................................................................
Summary of the content on the page No. 6
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 4 Viewing the Control Panel SOURCE (Power) Press to turn the TV on and off. Displays a menu of all of the available input sources (TV, DTV, Ext.1, Ext.2, AV, S-Video, Power Indicator Component, PC, HDMI). In the on-screen menu, use this button as you Blinks and turns off when the power is on and use the ENTER button on the remote control. lights up in stand-by mode. MENU Light Detecting Sensor Press to see an on-screen menu of Adjusts brightness o
Summary of the content on the page No. 7
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 5 Viewing the Connection Panel Power Input Whenever you connect an audio or video system to your set, ensure that all elements are switched off. When connecting an external device, match the color of the connection terminal to the cable. English-5
Summary of the content on the page No. 8
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 6 Viewing the Connection Panel Connecting an Aerial or Cable Television Network To view television channels correctly, a signal must be received by the set from one of the following sources: - An outdoor aerial - A cable television network - A satellite network Connecting Component Devices (DVD) - Connect component video cables to component connectors (“PR”, “PB”, “Y”) on the rear of your set and the other ends to corresponding component video out
Summary of the content on the page No. 9
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 7 Viewing the Connection Panel Connecting HDMI/DVI - Supports connections between HDMI-connection-enabled AV devices (set top boxes, DVD players and AV receivers). - No additional sound connection is needed for a HDMI to HDMI link What is HDMI? - HDMI, or high-definition multimedia interface, is a next-generation interface that enables the transmission of digital audio and video signals using a single cable without compression. - “Multimedia inte
Summary of the content on the page No. 10
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 8 Viewing the Connection Panel TV Rear Panel CI Card Please insert the card as shown Connecting CI (Common Interface) Card - When not inserting “CI Card” in some channels, “Scramble Signal” is displayed on the screen. - The pairing information containing a telephone number, CI CARD ID, Host ID, and other information will be displayed in about 2~3 minutes. If an error message is displayed, please contact your service provider. - When the channel
Summary of the content on the page No. 11
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 9 Viewing the Remote Control (All Functions Except Teletext) Television Standby button DTV MHEG menu display (Refer to page 12) Selects the DTV mode directly Selects the TV mode directly DTV Channel list display Number buttons for direct channel access Electronic Program Guide (EPG) display Previous channel Available source selection Temporary sound switch-off (Refer to page 48) (Refer to page 36) -Next channel -Volume increase -Previous channel -
Summary of the content on the page No. 12
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 10 Viewing the Remote Control (Teletext Functions) Teletext display/Mix both teletext information and he normal broadcast Teletext hold P : Teletext next page P : Teletext previous page Teletext mode selection LIST/FASTEXT Teletext reveal Teletext index Teletext size selection Teletext sub page Teletext cancel Teletext store Teletext Function : Refer to pages 78-80 for details English-10
Summary of the content on the page No. 13
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 11 Installing Batteries in the Remote Control 1 Remove the cover on the rear of the remote control by pressing the symbol ( ) downwards and then pulling firmly to remove it. 2 Install two AAA size batteries. Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment. 3 Replace the cover. Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time. The remo
Summary of the content on the page No. 14
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 12 Switching On and Off The mains lead is attached to the rear of your set. 1 Plug the mains lead into an appropriate socket. Result: The standby indicator lights up on the front panel. The main voltage is indicated on the rear of your set and the frequency is 50 or 60Hz. 2 Press the POWER button on the front of the panel. Result: The programme that you were watching last is reselected automatically. 3 Press the numeric button (0~9) or channel up/
Summary of the content on the page No. 15
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 13 Becoming Familiar with the Remote Control The remote control is used mainly to: Change channels and adjust the volume. Set up your set using the on-screen menu system. The following table presents the most frequently used buttons and their functions. Button Viewing Function Menu Function Used to display the - next stored channel. Used to display the - previous stored channel. to Used to display the corresponding channels. For double digit chan
Summary of the content on the page No. 16
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 14 Plug and Play When the set is initially powered ON, several basic customer settings proceed automatically and subsequently. The following settings are available. 1 If the set is in standby mode, press the POWER button on the remote control. Result: The message Démarrer Plug & Play is displayed. It appears for a little while, and then the Language menu is automatically displayed. 2 Select the appropriate language by pressing the or button. The av
Summary of the content on the page No. 17
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 15 Plug and Play If you want to reset this feature... In the case of DTV mode, Plug&Play can not be selected. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the or button to select Setup. Press the ENTER button. Result: The options available in the Setup group are displayed. 3 The Plug & Play is selected. 4 Press the ENTER button. Result: The message Start Plug & Play is displayed. 5 For further details on how to set, refer t
Summary of the content on the page No. 18
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 16 Storing Channels Automatically You can scan for the frequency ranges available to you (and availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However, you can sort numbers manually and clear any channels you do not wish to watch. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the or button to select Channel. Result: The options availabl
Summary of the content on the page No. 19
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 17 Storing Channels Manually You can store up to 100 channels, including those received via cable networks. When storing channels manually, you can choose: Whether or not to store each of the channels found. The programme number of each stored channel which you wish to identify. 1 Press the MENU button. Result: The main menu is displayed. 2 Press the or button to select Channel. Result: The options available in the Channel group are displayed. 3 P
Summary of the content on the page No. 20
01 BN68-00966A-00Eng.qxd 10/4/05 3:06 PM Page 18 Storing Channels Manually 9 If you know the number of the channel to be stored, Press the or button to select Channel and then press the ENTER button. Select C (Air channel) or S (Cable channel) by pressing the or button. Press the button to select channel. Select the required number by pressing the or button and then press the ENTER button. If there is an abnormal sound or no sound, re-select the sound system required. You can also set a cha
