Summary of the content on the page No. 1
DVD TELEVISION
DS21G5
DW21G5
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
FULL FLAT SCREEN
DVD / VIDEO-CD / CD / MP3
ON-SCREEN MENUS
TELETEXT FUNCTION (depending on the model)
ENG
Summary of the content on the page No. 2
Safety Instructions ENG Do not install the television in a confined space such as a book case or similar unit. Place on a stable stand or table. Do not expose the television to extreme temperature conditions or to extreme humidity conditions. Adequate ventilation is essential to prevent failure of electrical components. Do not expose the television to direct sunlight and other sources of heat. Do not expose the television to any liquids. During a storm conditions (especially when the
Summary of the content on the page No. 3
Contents Foreword ENG Safety Instructions................................................................................................................2 Caution ................................................................................................................................2 Viewing of the Television......................................................................................................4 Infrared Remote Control ............................................
Summary of the content on the page No. 4
Viewing of the Television ENG MENU DISPLAY CHANNEL SELECTION VOLUME ADJUSTMENT AUDIO INPUT CONNECTORS VIDEO INPUT CONNECTOR HEADPHONE JACK TELEVISION ON/OFF STAND-BY SKIP/SEARCH STOP INDICATOR (TITLE/CHAPTER/TRACK) REMOTE CONTROL SENSOR PLAY/PAUSE OPEN/CLOSE Rear of the TV 75Ω COAXIAL CONNECTOR FOR AERIAL/CABLE NETWORK RCA AUDIO/VIDEO INPUT/OUTPUT CONNECTORS OPTION DIGITAL AUDIO OUTPUTS 4
Summary of the content on the page No. 5
Infrared Remote Control (depending on the model) ENG TV DVD POWER TELEVISION STANDBY TV/DVD SELECTION Press this button during the play ➢ of DVD. The DVD will stop playing and then the mode is switched to the TV mode. Press this button during the view of TV and the mode is switched to NUMERIC BUTTONS the DVD play mode. PRE-CH SELECT A CHANNEL STORED AT PROGRAMME SWITCH REPEATEDLY BETWEEN THE LAST POSITION TEN OR HIGHER TWO CHANNELS DISPLAYED P NEXT CHANNEL/ VOLUME INCREASE TELETEXT NEXT PAGE MUT
Summary of the content on the page No. 6
Connecting the Aerial or Cable Television Network ENG To view television channels correctly, a signal must be received by the set from one of the following sources: Rear of the TV An outdoor aerial A cable television network Connect the aerial or network input cable to the 75Ω coaxial socket on the rear of the television. option or Cable Television Network Connecting a Decoder In order to descramble a coded transmission signal, you must connect a decoder to the TV set. Rear of the TV If you
Summary of the content on the page No. 7
Connecting to the Audio/Video Input/Outputs ENG The A/V connectors are used for equipment with an RGB output, such as VCRs, video game devices, ➢ video disc players, and camcorders. Rear of the TV VCR Video game device Camcorder Video disc player or Connecting to the RCA Input The RCA connectors are used for equipment, such as VCRs, camcorders, video disc players, and video ➢ game devices. Side of the TV VCR Video game device Camcorder Video disc player Connecting to the Audio Output (depending
Summary of the content on the page No. 8
Connecting Headphones ENG You can connect a set of headphones to your television if you wish to watch a television programme without disturbing the other people in the room. Side of the TV 1 Plug a set of headphones into the 3.5 mm mini-jack socket on the television panel. Result: The sound is heard through the headphones. 2 When you wish to hear the sound through the speakers again, simply disconnect the headphones. Prolonged use of headphones at a high volume may ➢ damage your hearing. Inserti
Summary of the content on the page No. 9
Switching Your Television On and Off ENG The mains lead is attached to the rear of your television. 1 Plug the mains lead into an appropriate socket. 2 Press the ON/OFF button ( ) on the front of the television. Result: The Standby indicator lights up on the front panel. 3 Press the POWER button ( ) on the remote control to switch the television on. Result: The programme that you were watching last is re- selected automatically. 4 To switch your television off, press the ON/OFF button ( ) again.
Summary of the content on the page No. 10
Becoming Familiar with the Remote Control ENG The remote control is used mainly to: Change channels and adjust the volume TV DVD POWER Set up the television using the on-screen menu system The following table presents the most frequently used buttons and their functions. Button Viewing Function P Used to display the next stored channel. PRE-CH P Used to display the previous stored channel. P to Used to display the corresponding channels. MUTE INPUT PRE-CH Used to switch repeatedly between t
Summary of the content on the page No. 11
Displaying Information on the Screen ENG You can display various types of information on the screen to help you use your television. Press the DISPLAY button to display the information. To remove the information from the screen, press the DISPLAY button again. OPEN RETURN /CLOSE Choosing Y our Language When you start using your television for the first time, you must select the language which will be used for displaying menus and MENU indications. PICTURE SOUND CHANNEL 1 Press the MENU button.
Summary of the content on the page No. 12
Storing the Channels Automatically ENG You can scan for the frequency ranges available to you, (availability depends on your country). Automatically allocated MENU programme numbers may not correspond to actual or desired PICTURE programme numbers. However you can sort numbers manually SOUND CHANNEL and clear any channels you do not wish to watch. FUNCTION 1 Press the MENU button. Result: The main menu is displayed. ADJUST SELECT EXIT 2 Press the UP/DOWN button until the CHANNEL is selected.
Summary of the content on the page No. 13
Storing the Channels Manually (depending on the model) ENG You can store up to 100 television channels, including those received via cable networks. MENU PICTURE When storing channels manually, you can choose: SOUND CHANNEL Whether or not to store each of the channels found FUNCTION The programme number by which you wish to identify each stored channel To entry the frequency of the channel to be stored directly, if you know it ADJUST SELECT EXIT 1 Press the MENU button. CHANNEL MANUAL
Summary of the content on the page No. 14
Storing the Channels Manually (depending on the model) ENG 6 If you... Then... CURRENT PR. : P01 NEW PR. : P08 Know the frequency Press the UP/DOWN button to SEARCH : of the channel select the FREQUENCY option. FREQUENCY : 192.00 MHz AFT : ON to be stored Enter the required frequency by SYSTEM : AUTO pressing the numeric buttons or S.SYSTEM : B/G the LEFT/RIGHT button. Go to Step 7. : : STORE X CLEAR EXIT 0 9 ADJUST SELECT Do not know the Press the UP/DOWN button t
Summary of the content on the page No. 15
Sorting the Stored Channels ENG The Sort operation allows you to change the programme numbers to previously stored channels or to clear channels that you will CHANNEL never watch. This operation may be necessary after you have MANUAL TUNE stored the channels automatically. You can delete those channels AUTO TUNE you do not want to keep. 1 Press the MENU button. Result: The main menu is displayed. ADJUST SELECT EXIT 2 Press the UP/DOWN button until the CHANNEL is selected. Press the LEFT/RIGH
Summary of the content on the page No. 16
Assigning Names to Channels (depending on the model) ENG Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing CHANNEL you to assign new names. MANUAL TUNE AUTO TUNE 1 Press the MENU button. Result: The main menu is displayed. 2 Press the UP/DOWN button until the CHANNEL is selected. Press the LEFT/RIGHT button. ADJUST SELECT EXIT Result: The options available in the CHANNEL menu are displayed with the MANUAL TUNE is selected
Summary of the content on the page No. 17
Adjusting the Picture (depending on the model) ENG You can select the type of picture which best corresponds to your viewing requirements. MENU PICTURE SOUND 1 Press the MENU button. CHANNEL Result: The main menu is displayed with the PICTURE is FUNCTION selected. 2 Press the LEFT/RIGHT button. Result: The options available in the PICTURE menu are ADJUST SELECT EXIT displayed. 3 Press the LEFT/RIGHT button to select the type of picture. PICTURE : CUSTOM The following picture effects are
Summary of the content on the page No. 18
Adjusting the Picture (depending on the model) ENG depending on the model. ☛ PICTURE : CUSTOM When the Wide signal is received from the broadcasting station, ADJUST COLOR TONE : NORMAL you can watch TV in the Wide mode. Otherwise, you can watch AUTO WIDE : OFF TV in the PANORAMA mode. SIZE : WIDE NR : OFF TILT : 0 8 Press the UP/DOWN button to select the AUTO WIDE option. To activate this feature, set the AUTO WIDE option to ON by pressing the LEFT/RIGHT button. ADJUST SELECT EXIT Whe
Summary of the content on the page No. 19
Adjusting the Sound ENG You can select the type of special sound effect to be used when watching a given broadcast. MENU PICTURE SOUND CHANNEL 1 Press the MENU button. FUNCTION Result: The main menu is displayed. 2 Press the UP/DOWN button until the SOUND is selected. Press the LEFT/RIGHT button. ADJUST SELECT EXIT Result: The options available in the SOUND menu are displayed. 3 Press the LEFT/RIGHT button to select the type of sound. The following sound effects are available: CUSTOM, STANDA
Summary of the content on the page No. 20
Selecting the Sound Mode (depending on the model) ENG The “AUDIO I-II” button displays/controls the processing and output of the audio signal. When power is switched ON, the mode P is automatically preset to either “Dual-I” or “Stereo”, depending MUTE INPUT on the current transmission. S.STD P.STD AUDIO TV/TEXT Type of broadcast On-screen indication Regular broadcast Mono (Normal use) (Standard audio) Regular + Mono ↔ Mono NICAM Mono Nicam (Normal) NICAM Stereo Stereo ↔ Mono NICAM Stereo Nicam
